2006 AUDI A4 econ

Overview13
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
You can find information about the different drives starting on page 34.Anti-theft codingGeneral
Effective safety measures in conjunction with the PIN
prevent misuse of the equipment by unauthorized
parties.The electronic lock-up is operational, if:

the Navigation System is removed from the vehicle,


the Navigation System is disconnected from the vehicle current
supply,


the battery is disconnected or


the electric fuse for the Navigation System is blown.
I f t h e a n t i - t h e ft c o d i n g h as l o cke d up t h e N a v i g a t i o n S ys t e m fo r o n e
of the reasons given, the speller display for entering the PIN
page 14, fig.6 appears after the Navigation System is switched
on.
After that, the Navigation System can only be operated again only
by entering the correct PIN.
This PIN is attached to the equipment card along with the equip-
ment number.
The PIN can be used for your equipment alone and cannot be
changed.
Note
The “equipment card” should be removed and kept in a safe place -
under no circumstances should it be kept in the vehicle. This makes
the Audi Navigation System unusable by thieves.Applies to vehicles: with convenience codingUser-friendly radio codingAft e r t he P I N i s e n t e re d t h e fir s t t im e , t h e N a v i g a t i o n S ys t e m g e t s to
know its vehicle.
If the power supply was interrupted, the Navigation System checks
to see whether it is still its vehicle. If it is, the Navigation System is
ready for use again after a few seconds.
It is no longer necessary to manually disable the electronic lock!
However, if the Navigation System is installed in another vehicle,
the electronic lock must be cancelled by entering the PIN page 14.

General system operation19
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP If you would like to scroll in an active radio station list using the
Forward/Reverse button, it is not necessary to show the station list
in the Navigation System display.
If the radio memory list
page 61 is shown in the Navigation
System display, you can select a a station from the memory list by
pressing the Forward/Reverse button.
Main CD function is active
Pressing the button calls up the next CD track. If the button is
held down, fast forward is activated.
You can jump back to the previous track by pressing the button
within the first 10 seconds of play time for a track. After 10
s e c o n d s i t j um p s t o t h e s t a r t o f t h e t ra ck. I f t h e b ut to n is he l d d o w n ,
reverse is activated.
If you would like to scroll in an active CD track list using the
Forward/Reverse button or activate forward/reverse it is not neces-
sary to show the CD operating menu in the Navigation System
display.
Main MP3 function is active
Pressing the button c alls up the n e xt in the MP3 p layer. If the
button is held down, fast forward is activated.
You can jump back to the previous track by pressing the button
within the first 10 seconds of play time for a track. After 10
s e c o n d s i t j um p s t o t h e s t a r t o f t h e t ra ck. I f t h e b ut to n is he l d d o w n ,
reverse is activated.
If you would like to scroll in an active MP3 track list using the
Forward/Reverse button or activate forward/reverse it is not neces-
sary to show the MP3 operating menu in the Navigation System
display.
Adjusting volumeVolume can be adjusted by turning the ON/OFF button. The volume
setting will be stored automatically.
If the volume is too high when the radio is turned on, it will be
reduced automatically to a level set by the factory. If the volume is
too low when the radio is turned on, it will be increased automati-
cally to a level set by the factory.
Tips
Volume can also be adjusted using the buttons on the multi-func-
tion steering wheel*
page 21.

|
A2
|
A1

|
A2
|
A1
Fig. 14 Navigation
System ON/OFF knob -
adjusting volume

General system operation 24You can perform the following functions with this
multi-function steering wheel:
The menu thumbwheel functions apply to the equipment which is
active at the time.
If you roll the left menu thumbwheel past several detents in CD
operation, several tracks are jumped.Button
Function
description
Operating
mode
Application
Roll the left
menu thumb-
wheel
up/down
Radio
Select the previ-
ous/next station on the
radio station list
a).
CD or MP3
Select the previ-
ous/next track for the
audio source you are
listening to.
First press on
left menu
thumbwheel
Radio
Start station frequency
scan forward
Second press
on left menu
thumbwheel
Radio
Stop station fre-
quency scan
Pres s and h old
left menu
thumbwheel
CD or MP3
Fast forward
button not applicable.
AAAAAAAB
MODE
Talk Button ( ) not applicable.Roll right
menu thumb-
wheel up
or down
Radio, CD or
MP3
Increase or reduce vol-
ume
Press the right
thumbwheel
Radio, CD or
MP3
Repeat the last naviga-
tion* announcement
with active route guid-
ance
a)If the radio memory list is shown in the Navigation System display, a radio
station can be selected from the list using the left menu thumbwheel.Button
Function
description
Operating
mode
Application
AC

AD

AD

Drives43
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
CD changerApplies to vehicles: with Audi cd changerLoading your CDs into the CD changerLoading just one CD
– Press the button . As soon as the CD changer
is ready for you to load a CD, the red LEDs on the inside
sides of the CD tray (not shown in the illustration)
start to blink.
– Insert the CD (printed side up and straight) into the CD
tray . The CD automatically loads into the next free slot
in the CD changer. The LED in the button will stop
blinking.Loading all CDs
– Press and hold the button for longer than 2
seconds.
– Wait until the red LEDs on the inside sides of the CD tray
(not shown in the illustration) start to blink.
– Now insert your other CDs (printed side up and straight)
o n e a t a t i m e i n t o t h e C D t r a y . Th e L E D s i n e a ch b u t t o n
will stop blinking once a CD has been loaded into the
slot.
Loading the CD into a specific empty slot
– Press the button . The LED in the button of
any empty slot will start to blink.
– If you want to load a CD into a specific slot, you can also
p r e s s a b u t t o n , w h e r e t h e L E D i s not lit a n d i n s e r t y o u r
CD.
– Wait until the red LEDs on the inside sides of the CD tray
(not shown in the illustration) start to blink.
– Now insert your CDs (printed side up and straight) into
the CD tray .
Loading the CD into a specific slot
– Press the button . The LEDs in the buttons
for the slots that already have CDs loaded blink.
– If you press an illuminated button that is not blinking
then that CD will be ejected.
– Remove the ejected CD from the CD tray .
Fig. 42 Audi cd
changer: Loading CDs
LOA D
A2
A;
A;
A3
LOA D
A2
A1
A;
A3
LOA D
A2
A
A3
A1
A;LOA D
A2
A A3
A1

Drives 44
– Insert a CD that you want to load, label up, into the CD
tray .If you press the button again while you are loading all CDs,
the loading process will be interrupted.
Make sure you load your CDs label side up and straight page 43, fig.42.
The CDs should never be forced into the slot. The CD will be pulled
into the CD changer automatically.
Aft e r a C D h as b e e n l o a d e d in to t h e CD ch a n g e r, yo u s h o u ld w a i t fo r
a moment until the red L ED on the inside side o f the tray blinks. The
CD tray is then ready to be loaded with the next CD.
If you choose a slot which already has a CD loaded in it, the CD will
be ejected. Remove the CD, and insert the new CD you want to have
in this slot.
I f yo u w a i t l o n g e r t h a n 3 0 s e c o n d s w i th o u t r e mo v in g t h e CD, th e C D
will be pulled back into the CD changer automatically.Tips


The CD is played through the main CD/SD function
page 78.


If you have accidently ins er ted a CD upside down (with the label
side facing down), the Display will show a read-error-message.


Never force the CDs into the CD tray. The CD will be pulled into
the CD changer automatically.


Do not use any non circular CDs (for example, Shape CDs)
page 49.
Applies to vehicles: with Audi cd changerEjecting CDsEjecting a CD
– Press the CD EJECT button
fig.43.
– Press the button (LED on) to eject an individual CD, or
– Press the CD EJECT button again to eject the CD you
are playing.
Ejecting all CDs
– Hold down the button for more than two seconds. All
CDs that are currently in the CD changer will be ejected.
Note

Always keep your CDs in their original cases to protect them
from dirt, dust, scratches or other damage.
A1
LOAD
A1
Fig. 43 Audi cd
changer: Ejecting CDs
A1A2A2
A1

RADIO 64
–Press the Tu n i n g control button in the FM/AM radio
menu.
– Using “Manual station search”
page 62 or “Automatic
seek”
page 63, select the station (or frequency) that
you wish to save.
– By rotating and pressing the control knob, select STORE
(“Store station”)
page 63, fig.61.
– Select your desired memory location by rotating the
control knob.
– Press the control knob to save the station.Using the control wheel, you can also save manually set radio
stations
page 62.
When you save a new station, an empty memory location will be
offered automatically. You can also choose any other memory loca-
tion.
You can find additional information about radio stations starting on
page 61. In Setup radio you can delete saved radio stations from
the memory list
page 67.
Automatic station scan (SCAN)Fig. 63 Radio: SCAN function–Press the Tuning control button in the FM/AM radio
menu.
– By rotating the control knob, select SCAN
fig.63.
– Press the control knob to begin scan. The receivable
stations are played for a few seconds.To s e l e c t t h e s t a t io n t h a t i s c urre n t l y b e i n g p l a y e d , p re s s t h e c o n t ro l
knob again.

RADIO73
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Applies to vehicles: with Satellite Digital Audio Radio ServiceDelete stored stationsDelete individual stations
– Press the function button in the satellite radio
menu.
–Select Delete stored stations
page 71, fig.72.
–Select Delete individually.
– Rotate and press the control knob to delete individual
stations from the memory list.
Delete all stations
– Press the function button in the satellite radio
menu.
–Select Delete stored stations.
–Select Delete all. All entries on the memory list are
deleted.Applies to vehicles: with Satellite Digital Audio Radio ServiceSystem informationThe following system messages can be displayed:XM Satellite Radio
Sirius Satellite Radio
SETUPSETUP
System mes-
sages
Meaning
ANTENNA
No antenna is connected to the tuner, or
there are loose plug contacts on the
antenna cable.
UPDATING
Your system is being updating.
NO SIGNAL
The tuner is presently not receiving any
satellite signal.
LOADING
Yo u r p ro v i d e r i s s e n d i n g i n fo r ma t i o n w h ich
the system is currently storing.
OFF AIR
The station selected has shut down its pro-
gram (e.g. children's channel at night)
INVALID
The channel is invalid or not used.
System mes-
sages
Meaning
LINKING
The tuner is presently not receiving any
satellite signal.
CALL 888-539-SIRIUS
TO SUBSCRIBE
First possibility: the tuner has not been
enabled yet. Second possibility: the station
selected is not enabled, for example
because the station requires a subscrip-
tion.

CD/SD81
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
CD Random play
CD tracks can also be played in random order.Fig. 81 CD: Random–Press the CD control button in the CD menu.
– By rotating the control knob, select MIX (“Random”)

fig.81.
– Press the control knob.The possibilities for Random play depend on the different settings
available for Repeat in the Setup CD menu
page 82.
I f y o u h a v e s w i t ch e d t he Repeat function off in Setup CD, the CDs in
a CD changer* are played one after the other in random order. The
tracks on the current CD are first played in random order. After all
the tracks have been played, the next CD is loaded.I f y o u s e t Repeat in Setup CD for only a single CD, only the tracks on
the current CD will be played in random order.
I f y o u h a v e s e t Repeat fo r a s i n g l e Tra c k in Setup CD, you cannot use
random play. The Scan function also cannot be used
page 81.
Scan CD tracksFig. 82 CD: Scanning a track–Press the CD control button in the CD menu.
– By rotating and pressing the control knob, select SCAN

fig.82.Pressing the control knob activates automatic track scan. Each track
on the CD will be played for a few seconds.