2006 ARIEL ATOM 2 fuel pressure

3

SPECIFICATION OVERVIEW


Engine Type:
General Motors: GM Ecotec LSJ
Honda : K20A

Transmission:
General Motors: 5-speed synchromesh with limited slip differential
Honda: 6-speed synchromesh with limited slip differential

Vehicle Capacity: 2 people

Safety Harness Restrictions: Individuals must be over 88 lbs (40 kg) and over 4 ft . 11 in. (150 cm) tall

Curb Weight: 1350 lbs (612.36 kg)

Body: Fiberglass composite, or carbon fiber composite

Suspension Type: Multilink Independent with pushrod actuation

Wheel Size: Front: 15 x 7.0 in. + 35 mm offset, Rear: 16 x 7.0 in. + 38 mm offset

Tire Pressure: (recommended) 18 PSIG Front, 20 PSIG Rear

Fuel Type/Capacity: Premium fuel, 9.7 gallons (36.7 liters)

5

DASH LAYOUT



The LCD panel includes readings for the total mileage , the trip odometer, the water temperature and the fuel
gauge. The fuel gauge will flash when the tank is app roaching empty. The panel settings are pre-programmed.
If you wish to modify the default settings, please con tact Brammo Motorsports for programming instructions.

NOTE: If your vehicle is equipped with non-canceling tur n signals, they must be cancelled manually.
1. Tachometer
2. Immobilizer
3. Charge System Warning
4. Parking Brake Indicator
5. Left Turn Signal
6. High Beam Indicator Light
7. Right Turn Signal
8. Lighting Indicator
9. Oil Pressure W arning
10. Speedometer
11. Turn Signal Switch
12. Horn
13. Engine Start Button
14. Ignition Power Switch
15. Emergency Flashers Button
16. Fog/Rain/Light
17. Marker/Lighting Selector/High
Beams
18. LCD Panel
19. Dash Programming Button

26

GM DRIVETRAINS

The Ecotec 2.0L SC (Supercharged) is compact and lightw eight, and its Eaton M62 Supercharger adds 40
percent more power to the Ecotec 2.0L engine compared to a naturally aspirated version. The M62
supercharger utilizes a helical roots compressor and integr al pressure control, producing a maximum of 12-19
PSI of boost. The boosted intake flow exits into an all-new matched intake manifold with an integral air- to-
liquid heat exchange intake charge cooler system. A comp act single-track, six-rib belt supercharger drive
system utilizes a linear tensioning device to further st rengthen the already impressive system performance and
durability. A microprocessor manages the M62 supercharge r, fuel, direct spark delivery systems and the
engine’s 68-mm Electronic Throttle Control (ETC) system . ETC delivers outstanding throttle response,
improved reliability and better integration with cru ise control electronics for greater overall performance a nd
drivability.
The Ecotec 2.0L SC engine is built with a six-quart oi l sump and a crankshaft driven pump. A block-mounted
oil cooler, or optional remote cooler, is included to e nsure proper lubricant cooling that promotes long engi ne
life.
The 2.0L SC engine is built exclusively at the FGP (Fi at-GM Powertrain) engine facility in Kaiserslautern,
Germany. This plant uses a die-cast production techniqu e that yields a block that is well suited for high-stress
applications including turbocharging and supercharging.
Often referred to as the Global Four Cylinder, the starting point for the 2.0L SC is the Ecotec 2.2L (RPO L61).
This engine has leveraged GM Powertrain’s worldwide de sign and engineering capability by drawing on the
best practice of technical centers in North America and Eu rope. The Ecotec 2.2L created a template for
subsequent global powertrain development that laid th e groundwork for engines such as Powertrain’s new
Global 3.6: V6. Most important, the Ecotec 2.2L is a world-class gasoline engine with obvious benefits for the

54

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE I: GENERAL REFERENCE

Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Replace every 30,0 00 miles (48,000 km). Supercharger
Aftercooler Coolant Check before every track event. Replace every 30,0
00 miles (48,000 km). Air Filter Check before every track event. Clean and oil ever
y 5,000 miles (8,000 km). The Filtercharger®
element must be cleaned and serviced with K&N clean er and air filter oil per the prescribed routine
maintenance procedures as outlined in the product l iterature that accompanies the Filtercharger®. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event; change every 10,000 miles (16,000 km). Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Replace when thickness decreases to 19mm, when puls
ation is noted, or if cracking or other physical
damage is found during inspection. Refer to the br ake bedding procedures on page12. Brake Pads Inspect for pad damage, thickness issues or deterio
ration before every event. Replace brake pads
when brake rotors are replaced. Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System Use a wrench to inspect flange bolts for tightness
every 5,000 miles (8,000 km), check gaskets at
this time. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels Check wheel nut torque after the first 50 miles (80
km) of operation and before every track event
thereafter. Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check belt for cracking or abnormal wear every 3,00 0 miles (4,800 km). Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.

55

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE II: BEFORE EVERY TRACK EVENT
Component Service/Operation
Engine Oil
Check before every track event. Change as necessar y. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Supercharger
Aftercooler Coolant Check before every track event.
Air Filter
Check before every track event. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event. Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Refer to the Brake Bedding Procedures on page12. I
nspect and replace when thickness decreases
to 19mm, when pulsation is noted, or if cracking or other physical damage is found during inspection.

Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Refer to the brake bedding procedure s on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System
Visually inspect exhaust flange bolts for tightness and/or damage. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.