2006 Acura RSX lock

Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.Refill the engine with the
recommended oil.
Engine oil change capacity
(including f ilter):
Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available from your
dealer) is required. Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten the drain bolt to:
Check the oil f ilter to make sure
its gasket did not stick to the
engine block. A stuck gasket could
cause an oil leak.
Install a new oil f ilter according to
the instructions that come with it.
4. 3.
2. (Type-S) (RSX and Premium models)
Type-S RSX and Premium models
5. 6.
7.
Changing the Oil and Filter
176
WASHER
OIL DRAIN BOLT OIL FILTER
33 lbf·ft (44 N·m , 4.5 kgf·m)
29 lbf·ft (39 N·m , 4.0 kgf·m)
5.0 US qt (4.7
)
4.4 US qt (4.2
)

If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap on
the reserve tank. Put the radiator cap on, and
tighten it fully. Pour the coolant slowly and
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment. The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
2. 1. 3.
4.
5.
Engine Coolant
178
RADIATOR CAP
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

Pour the f luid slowly and caref ully so
you do not spill any. Clean up any
spill immediately; it could damage
components in the engine
compartment.Always use Acura Precision Craf ted
Power Steering Fluid. You may use
another power steering f luid as an
emergency replacement, but have
the power steering system f lushed
and ref illed with Acura PSF as soon
as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
Check the level on the side of the
reservoir when the engine is cold.
The f luid should be between the
UPPER LEVEL and LOWER LEVEL.
If not, add power steering f luid to the
UPPER LEVEL mark.
Power Steering Fluid
Maint enance
183
UPPER LEVEL LOWER LEVEL
Do not spill the power steering f luid
over the body, auto-tensioner, drive
belt and pulleys.
If spilled accidentally, wipe of f any
f luid completely.
Turning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

Install the rubber seal and make
sure it is right side up; it is marked
‘‘TOP.’’
Pull the battery back to its original
position, then install the bolt in the
hold-down, and tighten it securely. Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place. Turn on the
headlights to test the new bulb.
Install the neck of the windshield
washer reservoir on the bracket.
Then remove the bolt f rom the
battery hold-down, and caref ully
push the battery toward the
windshield to obtain enough
working space.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb. Remove the rubber weather seal
by pulling on the tab. Remove the electrical connector
f rom the bulb by pulling the
connector straight back.Install the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
3.
4. 5.
6.
7.
8.
2.
Lights
Driver’s Side
Maint enance
185
HOLD DOWN
WIRE
BULB
WEATHER SEAL
CONNECTOR

To change a high beam headlight
bulb, remove the electrical
connector f rom the bulb by
pushing on the tab and pulling the
connector down.
Remove the bulb by turning it one-
quarter turn counterclockwise.Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
3.
4.
5.
2. 1. 2. 1.
Lights
Replacing a Front T urn Signal
BulbReplacing a High Beam HeadlightBulb
186

Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the parking lights and
check that the new bulb is
working.
The f ront parking light bulb is
above the high beam headlight
bulb.
3.
4.
1.2.
3.
4.
Lights
Replacing a Front Parking Light
Bulb
Maint enance
187

The f ront side marker light bulb is
above the low beam headlight bulb.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
2.
3.
1. 4.
Lights
Replacing a Front Side Marker
Light Bulb
188

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Test the lights to make sure the
new bulb is working.
Reinstall the high-mount brake
light cover.
Open the hatch.
Remove the high-mount brake
light cover by pivoting it toward
the back of the vehicle.
Remove the socket by turning it
one-quarter turn counterclockwise. Open the hatch. Remove the light
assembly cover by pulling on the
tabontheoutsideedge.
2.
3. 1. 4.
5.
6.
7.
1.
CONT INUED
Replacing Rear Bulbs
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance
189
COVER
COVER BULB