2006 Acura RSX buttons

Playing a T ape
110
FF BUTTON
PLAY BUTTON
PROG BUTTON REW BUTTON
POWER/VOLUME
KNOB
DOLBY INDICATOR
TAPE DIRECTION INDICATOR
AM BUTTON
REPEAT BUTTON TAPE EJECT BUTTON
Type-S model
TAPE SLOT
REPEAT INDICATOR
CD BUTTONDOLBY BUTTON
SKIP BUTTONS
TAPE BUTTON
FM BUTTON

Playing a Disc
Features
113
LOAD BUTTONSKIP BUTTONS
REPEAT BUTTON
CD BUTTON
FM BUTTON
AM BUTTON
RANDOM BUTTON POWER/VOLUME
KNOB CD SLOT
REPEAT INDICATOR
RANDOM INDICATOR
CD EJECT BUTTON
Type-S model

µ
µ
Ó
Ó
ÓÓ
´ µ
´µ
With the ignition in the
ACCESSORY (I) or ON (II) position,
insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way and begin to play it. You
operate the CD player with the same
controls used f or the radio. The
number of the track playing is shown
in the display. The system will
continuously play a CD until you
change modes. Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the CD will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f . Press the AM/FM button to switch
to the radio while a CD is playing.
Press the CD button to play the CD.
For inf ormation on how to handle
and protect discs, see page .
Each time you press and release
, the player skips f orward to
the beginning of the next track.
Press and release to skip
backward to the beginning of the
previous track.
To move rapidly within a track, press
and hold the or . You will
see CUE or REW in the display.
This f eature plays the
tracks in random order. To activate
random play, press and release the
RDM button. You will see RDM in
the display. This continues until you
press the RDM button again. Pressing either of the SKIP buttons
also turns of f the repeat f eature. To continuously replay
a track, press and release the RPT
button. You will see RPT in the
display. Press the RPT button again
to turn it off.
121
CD Player
T o Stop Playing a CD
To Change Tracks (SKIP)
Protecting Discs
RANDOM REPEAT
Playing a Disc
114
Do not use CDs with adhesive labels.
The label can curl up and cause the CD
to jam in the unit.

µ
To load a single CD:
Press and release the load button.
When the CD number f or an
empty position starts to blink and
the green CD loaded indicator
comeson,youwillseeLOAdin
the display. Insert the CD into the
CD slot. Insert it only about
half way, the drive will pull it in the
rest of the way.
The system will load the CD and
begin playing it. You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD loaded indicator is of f ), and press
the preset button for that position (1
to 6). The system will stop playing
the current CD and start the loading
sequence. It will then play the CD
just loaded. Select the CD changer by pressing
the CD button. You will see ‘‘Cd’’ in
the display. The system will begin
playing the last selected CD in the
CD changer. You will see the CD and
track numbers displayed.
When that CD ends, the next CD in
the CD changer is loaded and played.
Af ter the last CD f inishes, the
system returns to CD 1.
To select a dif f erent CD, press the
appropriate Preset button (1 6). If
youselectanemptypositioninthe
CD changer, the system will go into
the loading sequence (see page ).
You can use the SKIP buttons while
a CD is playing to select passages
and change tracks.
If you press the load button while a
CD is playing, the system will stop
playing that CD and start the loading
sequence. It will then play the CD
just loaded.
1.
2.
3.
115
Operat ion
Disc Changer
116

Ó
ÓÓÓ µ
µ´
µ ´µ
To move rapidly within a track, press
and hold the appropriate SKIP
button. You will hear a beep and the
system will continue to move. Press
the button to move forward, or
the button to move backward.
Release the button when the system
reaches the point you want.
Each time you press the button
and release it, the system skips
f orward to the beginning of the next
track. Press and release the
buttontoskipbackwardtothe
beginning of the current track. Press
and release it again to skip to the
beginning of the previous track. To activate the repeat
f eature, press and release the RPT
button. You will see RPT in the
display as a reminder. The system
continuously replays the current
track. Press the RPT button again to
turn it off. Pressing either of the
SKIP buttons also turns off the
repeat feature.
This feature,
when activated, plays the tracks
within a CD in random order, rather
than in the order they are recorded
on the CD. To activate random play,
press the RDM button. You will see
RDM in the display. The system will
then select and play tracks randomly.
This continues until you deactivate
randomplaybypressingtheRDM
button again, or you select a
dif f erent CD with a preset button. To take the system out of CD mode,
press the AM or FM button, or insert
a tape in the player. If a tape is
already in the tape player, press the
TAPE button. When you return to
CD mode by pressing the CD button,
play will continue at the same point
that it lef t of f .
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
CONT INUED
REPEAT
RANDOM PLAY
Disc Changer
Features
117

If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code. If you are
unsuccessf ul in 10 attempts, you
must then leave the system on for 1
hour bef ore trying again.
If thecodecardislost,yourdealer
can access your code with your
radio’s serial number. To access the
serial number, turn the radio on. Itmust display ‘‘COdE’’, then turn the
radio of f . Push the preset 1, preset 6,
and power buttons at the same time,
then quickly release.
You will have to store your favorite
stations in the preset buttons after
the system begins working. Your
original settings were lost when the
power was disconnected.
Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code in the
preset buttons. Because there are
hundreds of number combinations
possible f rom f ive-digits, making the
system work without knowing the
exact code is nearly impossible.
Youshouldhavereceivedacardthat
lists your audio system’s code
number and serial number. It is best
tostorethiscardinasafeplaceat
home. In addition, you should write
the audio system’s serial number in
this owner’s manual. If you lose the
card, you must obtain the code
number f rom your dealer. To do this,
you will need the system’s serial
number. If your vehicle’s battery is
disconnected or goes dead, or the
radio f use is removed, the audio
system will disable itself . If this
happens, you will see ‘‘COdE’’ in the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons to enter the five-digit code.
The code is located on the radio code
card included in your owner’s
manual kit. When it is entered
correctly, the radio will start playing.
Theft Protection
Radio T hef t Protection
Features
125

µ
Check the condition of the battery
monthlybylookingatthetest
indicator window. The label on the
battery explains the test indicator’s
colors.
Check the terminals f or corrosion (a
white or yellowish powder). To
remove it, cover the terminals with a
solution of baking soda and water. It
will bubble up and turn brown. When
this stops, wash it of f with plain
water. Dry off the battery with a
cloth or paper towel. Coat the terminals with grease to help prevent
f urther corrosion.
If additional battery maintenance is
needed, see your dealer or a
qualif ied technician.
Battery posts,
terminals, and related accessories
contain lead and lead compounds.
If your vehicle’s battery is
disconnected or goes dead, your
driver’s power window loses its
calibration and must be
reprogrammed (see page ), and
your audio system will disable itself .
Thenexttimeyouturnontheradio
youwillsee‘‘ ’’inthe
f requency display. Use the Preset
buttons to enter the five-digit code
(see page ). If you need to connect the battery to
a charger, disconnect both cables to
prevent damaging your vehicle’s
electrical system. Always disconnect
the negative ( ) cable first, and
reconnect it last.
78
125
Checking the Battery
WARNING:
Wash your hands af ter handling.
200
TEST INDICATOR WINDOW
The battery gives off explosive
hydrogen gas during normal
operation.
A spark or flame can cause the
battery to explode with enough
force to kill or seriously hurt you.
Wear protective clothing and a
face shield, or have a skilled
mechanic do the battery
maintenance.

If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualif ied mechanic.If the driver’s power window f use is
removed, the AUTO function of the
driver’s window will be disabled. To
reset the AUTO f unction, see page
.
If the radio f use is removed, the
audio system will disable itself . The
nexttimeyouturnontheradioyou
will see ‘‘Code’’ in the f requency
display. Use the preset buttons to
enter the f ive-digit code (see page ).
If you cannot drive the vehicle
without f ixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
f rom one of the other circuits. Make
sureyoucandowithoutthatcircuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown f use with a
spare f use that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
f use with one of the correct rating as
soon as you can.
6. 78
125
Fuses
222
Replacing a f use with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement f use with the proper rating
f or the circuit, install one with a lower
rating.