2006 Acura RL Multi information display

When a problem is detected with
your vehicle, a message will be
shown on the multi-inf ormation
display.
If this happens, refer to the
applicable pages of this owner’s
manual, and f ollow the instructions.
When there are several messages to
be shown, the system switches the
messages every 5 seconds.
The message is shown until you
push the INFO button.
To see the message again, press the
INFO button, 5 seconds af ter the
display disappears.
Here is a list of messages shown on
the multi-information display:See page
63,411
See page 411
See page 62,409
See page 62,410
See page 62,409
See page 312
See page 408 See page
65,339
See page 69,139
See page 68
See page 67, 320
See page 34, 63
See page
312
See page
64,323
Multi-Inf ormation Display
Message Display
78

ÛÝÛÝ
With the multi-information display
and the INFO ( / ) and SEL/
RESET buttons on the right side of
the steering wheel, you can
customize some vehicle control
settings f or ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’. If ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ is not displayed,
customizing is not possible.
To have the driver’s ID detected,
make sure your remote is linked to
the system (see
on page ). Then use your
remote to unlock the doors (see on page
). To enter the customizing mode,
press and hold the INFO ( / )
button for more than 3 seconds while
the multi-information display is in its
normal mode.
If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
When the multi-information
display does not show the driver’s
ID. The f irst customizing menu is:
CHG SETTING (see page )
If you disconnect the battery, and
then do not unlock the door. When the keyless memory
settings are of f (see page ). DEFAULT ALL (see page )
You cannot customize the settings
under these conditions:
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park. 82
84
166
100
105
CONT INUED
Customized Settings
Memory Position
Link
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
81

Û
Ý
ÛÝ
You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize:
While the multi-information display
is in the CUSTOMIZE ENTRY
screen, press the SEL/RESET
button. The screen changes to the
initial CUSTOMIZE GROUP display.
METER SET UP ADAPTIVE CRUISE CONTROL
SETUP
Each time you press the INFO ( /) button, the screen changes as
shownonthenextpage.Pressthe
INFO ( / ) button, until you see
the setup you want to customize,
then press the SEL/RESET button
to enter your selection.
POSITION SET UP
LIGHTING SET UP
DOOR/WINDOW SET UP
WIPER SET UP
Multi-Inf ormation Display
Customize Settings
84

ÛÝÛ
Ý
ÛÝ
ÛÝ
If equipped
Here are the two custom settings for
adaptive cruise control (ACC):PRE-RUNNING CAR DETECT
BEEP
ACC DISPLAY SPEED UNIT
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select ACC SETUP by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
Each time you press the INFO ( / ) button, the display changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
A daptive Cruise Control Setup
86
Press the or button.
Press the SEL/RESET button. seepage87
seepage89

ÛÝ
While the multi-information display
is in the ACC SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to the above display. Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
When PRE-RUNNING CAR
DETECT BEEP is set to ON, one
beep sounds when the ACC detects a
vehicle in f ront of you. You also hear
a beep when that vehicle goes out of
the range of your vehicle’s radar
sensor.
CONT INUED
Multi-Inf ormation Display
Pre-Running Car Det ect Beep
Inst rument s and Cont rols
87

ÛÝÛÝ
While the multi-information display
is in the ACC SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display. Press the SEL/RESET button. The
screen changes as shown above. The
highlighted unit, mph or km/h, is
the current setting. To change the
setting, press the INFO ( / )
button until the unit you want is
highlighted, then press the SEL/
RESET button.
To change the unit of measurement
f rom mph to km/h, do this:
CONT INUED
Multi-Inf ormation Display
A dapt ive Cruise Cont rol Display
Speed Unit
Inst rument s and Cont rols
89

ÛÝÛ
Ý
ÛÝ
ÛÝ
CONT INUED
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
TRIP A & AVG. FUEL A RESET
with REFUEL
Here are the f our custom settings
forthemetersetup:
ELAPSED TIME RESET
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select METER SETUP by
pressing the INFO ( / ) button,
and then press the SEL/RESET
button.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Meter Setup
Inst rument s and Cont rols
91
Press the or button.
Press the SEL/RESET button. seepage92
seepage98
seepage96
seepage94

ÛÝ
There are three language selections
you can make: English, French, and
Spanish. To choose the language you
want, f ollow these instructions:
While the multi-information display
is in the meter setup of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to the above display.Select the desired language by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
L anguage Select ion
92