2006 Acura MDX ECU

Both f ront seats are equipped with
seat heaters. The passenger seat is
only heated in the seat bottom
because of the side airbag of f system.
The ignition switch must be in the
ON (II) position to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
To f old the third row seat,
the second row must be f olded down
or completely up right.
Unlock the seat-back by pulling
the handle. Push the seat-back
forward.
Make sure the outer shoulder belts
are positioned on each hook
whenever the third seat is f olded.
Reverse this procedure to return the
seat to the upright position. Make
sure the seat is locked securely
bef ore driving. Reinstall the head
restraints. Reconnect the seat belts
to the detachable anchors.
Make sure all items in the cargo area
are secured. Loose items can f ly
f orward and cause injury if you have
to brake hard (See
on page ). In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat temperature drops.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Follow these precautions when using
the seat heaters:
Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters, even on the LO
setting. It can weaken the battery,
causing hard starting.
4.
195 Seat Heaters
Carrying Cargo
Seats, Seat Heaters
Inst rument s and Cont rols
91
NOTE:
SEAT HEATERS

Storage compartments are located in
the armrests f or the third row seat.
To open a compartment, pull the
lever and lif t the lid.
The hooks on the f loor of the cargo
area enable you to tie down items
stored in the back. Make sure all
stored items are secured bef ore
driving.Whenusingthesunvisorforthe
side window, remove the support rod
f rom the clip and swing it out. Slide
the extension out to get more
coverage on the side window.
Make sure you put the sun visor
back in place when you are getting
into or out of the vehicle. Do not use
the sun visor extension over the rear
view mirror.Pull up the vanity mirror cover to use
it.
The light comes on only when the
parking lights or headlights are on.
Rear Compartment
Cargo Hooks
Sun Visor
Vanity Mirror
Interior Convenience Items
Inst rument s and Cont rols
103
EXTENSION
SUN VISOR

The standard audio system has
many f eatures. This section
describes those f eatures and how to
use them. (If you selected an
optional audio system, ref er to the
operating instructions that came
with it.) The climate control system in your
vehicle provides a comfortable
driving environment in all weather
conditions.
Your vehicle has an anti-theft audio
system that requires a code number
to enable it..............
Vents, Heating, and A/C . 106
.............................
Airflow Buttons .107
...................
Rear Climate Control . 111
..............
Climate Control Sensors . 111
..........................
Playing the Radio .112
............................
Radio Reception .116
........
Playing XM
Satellite Radio . 118
..................................
Playing a CD .123
...................................
CD Changer .126
....................
Protecting Your CDs .128
.....
CD Changer Error Messages . 129
.............
Steering Wheel Controls . 130
.................
Radio Thef t Protection . 131
........
Rear Entertainment System . 132
............................
Security System .145
...............................
Cruise Control .146
..............................
Trip Computer .149
.
Rear View Camera and Monitor . 155
HomeLink Universal ................................
Transceiver .156
..........................
HandsFreeLink .161
............................................
OnStar .175
Features
Features
105
TM

The security system automatically
sets 15 seconds after you lock the
doors, hood, and the tailgate. For the
system to activate, you must lock the
doors f rom the outside with the key,
lock tab, door lock switch, or remote
transmitter. The security system
indicator next to the driver’s door
lock starts blinking immediately to
show you the system is setting itself .The security system will not set if
the hood, tailgate, or any door is not
f ully closed. If the system will not set,
check the Door and Tailgate Open
Monitor on the instrument panel
(see page ) to see if the doors and
tailgate are f ully closed. Since it is
notpartofthemonitordisplay,
manually check the hood.
Once the security system is set,
opening any door or the tailgate
without using the key or the remote
transmitter, or opening the hood, will
cause it to alarm. It also alarms if the
radio, navigation and DVD
components are removed f rom the
dashboard or the wiring is cut. Use the remote transmitter
to quickly check that the hood,
tailgate and all doors are closed.
Push the lock button twice. There
should be an audible conf irmation
beep.
Do not attempt to alter this system
or add other devices to it.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights and parking lights f lash
if someone attempts to break into
your vehicle or remove the radio or
navigation and DVD components.
This alarm continues f or 2 minutes,
then the system resets. To reset an
alarming system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
62
Security System
Features
145
NOTE:
SECURITY SYSTEM INDICATOR

µ
The HomeLink
universal
transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manuf actured bef ore
April 1982, you may not be able to
program HomeLink to operate it.
They do not have the saf ety f eature
that causes the motor to stop and reverse if an obstacle is detected
during closing, increasing the risk of
injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
If you are training the second or
third buttons, go directly to step 1.If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
For quick and accurate training,
make sure the remote control
transmitter for the device (garage
door, automatic gate, security
system, etc.) has a fresh battery.
General Inf ormation
T raining HomeL ink
Important Saf ety Precautions
HomeL ink Universal Transceiver
Bef ore you begin
156

Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.
For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink.
If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
If the indicator f lashes rapidly
f or 2 seconds then stays on, you
have a rolling code transmitter:
Go to ‘‘Training with a Rolling
Code System’’ (see page ).
Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled devices
around your home (lighting,
automatic gate, security system,
etc.).
2. 1. 3.
6.
7.
158
HomeL ink Universal Transceiver
T raining With a Rolling Code
System
158
TRAINING BUTTON

To go back one step in a command
process, say, ‘‘Go back,’’ or press
the Back button.
If nothing is said while the HFL is
listening f or a command, the HFL
will time out and stop its voice
recognition. The next time you
press the top of the TALK/BACK
button, the HFL begins listening
f rom the point at which it timed
out.
When you f inish a command
sequence, the HFL goes back to
its main menu. For example, when
you store the name, ‘‘Eric,’’ the
HFL response is, ‘‘Eric has been
stored.’’ The next time you pressthe Talk button, you will be at the
main menu.
To end a command sequence at
any time, press and hold the Back
button, or press the Talk button,
wait f or the beep, and say, ‘‘Cancel.’’
ThenexttimeyoupresstheTalk
button, the HFL begins f rom its
main menu. The HFL will accept a numeric, f our-
digit passcode that you can use f or
security purposes.
With the ignition in the ON (II)
position, press and release the top
of the TALK/BACK button on the
steering wheel. Af ter the beep, say
‘‘Security.’’ The HFL response is
‘‘Security options are lock, unlock,
and set passcode.’’ Press and release the top of the
TALK/BACK button. After the
beep, say the f our-digit passcode
you want to use. For example, say
‘‘1,2,3,4.’’TheHFLresponseis
‘‘1,2,3,4.Isthiscorrect?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Yes.’’ The HFL
response is ‘‘The new passcode
has been stored. Returning to the
main menu.’’
Once a passcode is set, you can lock
the HFL so it only operates after the
passcode is entered, or you can
unlock it so anyone using your
vehicle can also use the HFL.
The HFL response is ‘‘What is the
new f our-digit passcode?’’ (If you
are changing the passcode, you
will f irst be asked f or the current
passcode.) Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Set passcode.’’
2. 1. 4.
5.
3.
To set your passcode, do this:
Setting Your Passcode L ocking or Unlocking the HFL
HandsFreeL ink
164
TM

Thevoiceof theHFLcanbesetto
male or f emale (U.S. models only).
Also, the incoming notif ication can
be set to a ring tone, a prompt, or no
notification.Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘System.’’ The HFL
response is, ‘‘System options are
setup and clear.’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Ring tone’’ or ‘‘Prompt.’’
If you choose ‘‘Ring tone’’ you will
hear a ring tone through the audio
speakers to announce an incoming
call. If you choose ‘‘Prompt,’’ you
will hear this message to
announce an incoming call: ‘‘You
have an incoming call.’’ Press and release the top of the
TALK/BACK button. If you say
‘‘Yes’’ af ter the beep, the HFL
response is, ‘‘Would you like a ring
tone or a prompt?’’ If you say ‘‘No’’
af ter the beep, the HFL returns to
its main menu. Saying ‘‘No’’ will
result in no ring tone or prompt
playback during an incoming call.
The audio system will still mute,
and a message will be displayed.
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Male’’ or ‘‘Female,’’
depending on the system voice
you want. The HFL response is,
‘‘Male (Female) prompts have been selected. Would you like an
audible notif ication of an incoming
call?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Setup.’’ The HFL
response is ‘‘Would you like male
or f emale prompts?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Security.’’ The HFL
response is ‘‘Security options are
lock, unlock, and set passcode.’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Lock’’ or ‘‘Unlock.’’
Lock means the HFL will prompt
you f or your passcode each time
the ignition switch is turned to the
ON (II) position and you press the
Talk button. You will only be
askedforthepasscodeonceper
ignition cycle. If the HFL is locked,
its response is ‘‘System is locked.
Each time the vehicle is turned on,
the passcode will be required to
use the system.’’ If the HFL is
unlocked, its response is ‘‘The
system is unlocked. Returning to
the main menu.’’
2. 1.
4.
5.
3.
2. 1.
To set up the system, do this:
To lock or unlock the HFL, do this:
Setting Up the System
HandsFreeL ink
Features
165
TM