2005 YAMAHA YZ250LC oil

2-8
CARACTERISTIQUES D’ENTRETIENSPEC
Article Standard Limite
Roue:
Type de roue avant Roue à rayons…
Type de roue arrière Roue à rayons…
Taille/matériau de jante avant 21 ×1,60/Aluminum…
Taille/matériau de jante arrière 19 ×2,15/Aluminum…
Limite de voile de jante:
Radial…
2,0 mm (0,08 in)
Latéral…
2,0 mm (0,08 in)
Chaîne de transmission:
Type/fabricant DID520DMA2 SDH/DAIDO…
Nombre de maillons 113 maillons + attache…
Flèche de la chaîne 48~58 mm (1,9~2,3 in)…
Longueur de chaîne (15 maillons)…
242,9 mm (9,563 in)
Frein à disque avant:
Dia. extérieur ×épaisseur 250 ×3,0 mm 250 ×2,5 mm
(9,84 ×0,12 in) (9,84 ×0,10 in)
Epaisseur de plaquette 4,4 mm (0,17 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 27,0 mm (1,063 in) ×2…
Type de liquide de frein DOT #4…
Frein à disque arrière:
Dia. extérieur ×épaisseur 245 ×4,0 mm 245 ×3,5 mm
(9,65 ×0,16 in) (9,65 ×0,14 in)
Limite de flèche…
0,15 mm (0,006 in)
Epaisseur de plaquette 6,4 mm (0,25 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 25,4 mm (1,000 in)…
Type de liquide de frein DOT #4…
Levier de frein & pédale de frein:
Position du levier de frein 95 mm (3,74 in)…
Hauteur de la pédale de frein Zéro mm (Zéro in)…
(hauteur au-dessus du haut du repose-pied)
Jeu de levier d’embrayage (côté levier) 8~13 mm (0,31~0,51 in)…
Jeu à la poignée d’accélération 3~5 mm (0,12~0,20 in)…
1P8-9-30-2 19/5/04 9:08 AM Page 22

2-14
CABLE ROUTING DIAGRAMSPEC
EC240000
CABLE ROUTING DIAGRAM
1Radiator hose
2Throttle cable
3Clutch cable
4“ENGINE STOP” button lead
5Radiator breather hose
6C.D.I. magneto lead
7Ignition coil leadAPass the clutch cable on the out-
side of the throttle cable and
“ENGINE STOP” button lead.
BPass through the cable guide the
throttle cable, “ENGINE STOP”
button lead and clutch cable.
CAlign the throttle cable locating
tape with the cable guide.
DPass above the radiator hose the
throttle cable, “ENGINE STOP”
button lead and clutch cable.
EClamp the “ENGINE STOP” but-
ton lead to the frame.
FClamp to the frame the throttle
cable, clutch cable, TPS (throttle
position sensor) lead and sole-
noid valve lead.
GClamp to the frame the throttle
cable, TPS (throttle position sen-
sor) lead and solenoid valve
lead.HPass the clutch cable in front of
the center of the cylinder head
tightening nut.
IPass the air vent hose, overflow
hose and crankcase breather
hose between the frame and
connecting rod.
JLocate the clamp ends in the
arrowed range.
1P8-9-30-2 16/6/04 11:47 AM Page 54

2-15
CABLE ROUTING DIAGRAMSPEC
1Clamp
2Radiator hose
3Solenoid valve lead
4TPS (throttle position sensor)
lead
5Air vent hose (left)
6Crankcase breather hose
7Overflow hose
8Air vent hose (right)AInsert the tip of the fuel tank
breather hose into the hole in
the steering shaft cap.
BPass the radiator breather hose,
ignition coil lead and C.D.I.
magneto lead between the
frame and the left of the radia-
tor.
CClamp the C.D.I. magneto lead
and ignition coil lead to the
frame.
DInstall the side core and ignition
coil together to the frame.
EPass the radiator breather hose
from the outside of the engine
bracket to the inside of the
downtube. Pass the radiator
breather hose on the inside of
the C.D.I. magneto lead.
FClamp the C.D.I. magneto lead,
radiator breather hose and
Y.P.V.S. breather hose. GClamp to the frame the radiator
breather hose and C.D.I. mag-
neto lead.
HPass the C.D.I. magneto lead
and radiator breather hose in
front of the radiator hose.
IPass the throttle cable behind
the air vent hose.
JPass the air vent hose, overflow
hose and crankcase breather
hose so that they do not contact
the rear shock absorber.
KClamp the air vent hoses.
1P8-9-30-2 16/6/04 11:47 AM Page 56

2-16
CABLE ROUTING DIAGRAMSPEC
1Clamp
2High tension cord
3C.D.I.unit
4“ENGINE STOP” button lead
5Ignition coil lead
6Radiator hose
7Radiator breather hose
8Throttle cable
9Clutch cable
0WireharnessAClamp the wireharness to the
right engine bracket.
BPass the high tension cord to
the right of the radiator hose.
CPass the C.D.I. unit lead
between the frame and the right
side of the radiator and then
above the radiator fitting boss.
DPass the radiator breather hose
behind the radiator hose.
ELocate the clamp ends in the
arrowed range.
F
Insert the C.D.I. unit band until it
stops at the C.D.I. unit stay.
1P8-9-30-2 16/6/04 11:47 AM Page 58

INSP
ADJ
3-1
MAINTENANCE INTERVALS
EC300000
REGULAR INSPECTION AND ADJUSTMENTS
EC310013
MAINTENANCE INTERVALS
The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind
that such factors as weather, terrain, geographical location, and individual usage will alter the required
maintenance and lubrication intervals. If you are a doubt as to what intervals to follow in maintaining
and lubricating your machine, consult your Yamaha dealer.
Item Remarks
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
Inspect crack
Inspect carbon deposits
and eliminate them
Check ring end gap
Inspect carbon deposits
and eliminate them
Check gasket
Inspect score marks
Inspect wear
Inspect carbon deposits
and eliminate them
Inspect housing, friction
plate, clutch plate and
spring
Yamalube 4 (10W-30) or
SAE 10W-30 SE motor oil
Inspect wear
Use chain lube
Chain slack: 48~58 mm
(1.9~2.3 in) PISTON
Inspect and clean
Replace
PISTON RING
Inspect
Replace
PISTON PIN, SMALL END BEARING
Inspect
Replace
CYLINDER HEAD
Inspect and clean
Retighten
CYLINDER
Inspect and clean
Replace
YPVS
Inspect and clean
CLUTCH
Inspect and adjust
Replace
TRANSMISSION
Replace oil
Inspect
Replace bearing
SHIFT FORK, SHIFT CAM, GUIDE BAR
Inspect
ROTOR NUT
Retighten
MUFFLER
Inspect
Clean
Retighten
CRANK
Inspect and clean
CARBURETOR
Inspect, adjust and clean
SPARK PLUG
Inspect and clean
Replace
DRIVE CHAIN
Lubricate, slack, alignment
Replace
1P8-9-30-3A 11/5/04 10:44 AM Page 2

INSP
ADJ
3-2
MAINTENANCE INTERVALS
3
Item Remarks
COOLING SYSTEM
Check coolant level and leakage
Check radiator cap operation
Replace coolantEvery two years
Inspect hoses
OUTSIDE NUTS AND BOLTS Refer to “STARTING
RetightenAND BREAK-IN” section
in the CHAPTER 1.
AIR FILTER
Clean and lubricateUse foam air-filter oil or
Replaceequivalent oil
FRAME
Clean and inspect
FUEL TANK, COCK
Clean and inspect
BRAKES
Adjust lever position and pedal height
Lubricate pivot point
Check brake disc surface
Check fluid level and leakage
Retighten brake disc bolts, caliper bolts,

master cylinder bolts and union bolts
Replace pads
Replace brake fluidEvery one year
FRONT FORKS
Inspect and adjust
Replace oilSuspension oil “S1”
Replace oil seal
FRONT FORK OIL SEAL AND DUST SEAL
Clean and lubeLithium base grease
PROTECTOR GUIDE
Replace
REAR SHOCK ABSORBER
(After
Inspect and adjustrain ride)
Lube Molybdenum disulfide grease
Retighten
CHAIN GUARD AND ROLLERS
Inspect
SWINGARM
Inspect, lube and retightenMolybdenum disulfide grease
RELAY ARM, CONNECTING ROD
Inspect, lube and retightenMolybdenum disulfide grease
STEERING HEAD
Inspect free play and retighten
Clean and lubeLithium base grease
Replace bearing
TIRE, WHEELS
Inspect air pressure, wheel run-out,

tire wear and spoke looseness
Retighten sprocket bolt
Inspect bearings
Replace bearings
LubricateLithium base grease
THROTTLE, CONTROL CABLE
Check routing and connectionYamaha cable lube or
LubricateSAE 10W-30 motor oil
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
1P8-9-30-3A 11/5/04 10:44 AM Page 3

3-3
PROGRAMME D’ENTRETIEN
INSP
ADJ
PartieAprès Chaque Chaque Chaque Si
Remarques
rodage coursetrois- cinquiè- nécessa-
ième me ire
BRAS OSCILLANT
Contrôler, lubrifier et resserrer
66
BRAS RELAIS, BIELLE
Contrôler, lubrifier et resserrer66
TETE DE FOURCHE
Contrôler le jeu66
Nettoyer et lubrifier6
Changer le roulement6
PNEU; ROUES
Contrôler la pression de gonflage,
le voile de roue et l’usure des
66pneus et voir s’il n’y a pas de
rayon détendu
Resserrer les boulons de la roue
66dentée
Contrôler les roulements6
Changer les roulements6
Graisser6
ACCELERATEUR, CABLES DE
COMMANDE
Contrôler le chaminement et le
66branchement
Graisser66
Graisse au bisulfure de
molybdène
Graisse au bisulfure de
molybdène
Graisse à base de lithium
Graisse à base de lithium
Yamaha lube pour câble ou
Huile moteur SAE 10W-30
1P8-9-30-3A 11/5/04 10:44 AM Page 7

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~24
results of test runs before racing? Are inspection and
maintenance completely done?
1P8-9-30-3A 11/5/04 10:44 AM Page 14