2005 YAMAHA YZ125LC oil

2-8
SPECCARACTERISTIQUES D’ENTRETIEN
Article Standard Limite
Roue:
Type de roue avant Roue à rayons…
Type de roue arrière Roue à rayons…
Taille/matériau de jante avant 21 ×1,60/Aluminum…
Taille/matériau de jante arrière 19 ×1,85/Aluminum…
Limite de voile de jante:
Radial…
2,0 mm (0,08 in)
Latéral … 2,0 mm (0,08 in)
Chaîne de transmission:
Type/fabricant DID520DMA2 SDH/DAIDO…
Nombre de maillons 111 maillons+attache…
Flèche de la chaîne 48~58 mm (1,9~2,3 in)…
Longueur de chaîne (15 maillons)…
242,9 mm (9,563 in)
Frein à disque avant:
Dia. extérieur ×épaisseur 250 ×3,0 mm 250 ×2,5 mm
(9,84 ×0,12 in) (9,84 ×0,10 in)
Epaisseur de plaquette 4,4 mm (0,17 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 27,0 mm (1,063 in) ×2…
Type de liquide de frein DOT #4…
Frein à disque arrière:
Dia. extérieur ×épaisseur 245 ×4,0 mm 245 ×3,5 mm
(9,65 ×0,16 in) (9,65 ×0,14 in)
Limite de flèche…
0,15 mm (0,006 in)
Epaisseur de plaquette 6,4 mm (0,25 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 25,4 mm (1,000 in)…
Type de liquide de frein DOT #4…
Levier de frein & pédale de frein:
Position du levier de frein 95 mm (3,74 in)…
Hauteur de la pédale de frein Zéro mm (Zéro in)…
(hauteur au-dessus du haut du repose-pied)
Jeu de levier d’embrayage (côté levier) 8~13 mm (0,31~0,51 in)…
Jeu à la poignée d’accélération 3~5 mm (0,12~0,20 in)…
1C3-9-30-2A 25/5/04 7:13 PM Page 21

2-13
SPECCABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1Ground lead
2High tension cord
3Grommet
4Air vent hose
5Crankcase breather hose
6Y.P.V.S. breather hose
7Throttle cable
8Clutch cable
9Engine bracket (right)
0Engine bracket (left)
qAir vent hose (left)
wAir vent hose (right)
e“ENGINE STOP” button leadAPass the clutch cable on the
outside of the throttle cable and
“ENGINE STOP” button lead.
BInsert the tip of the fuel tank
breather hose into the hole in
the steering shaft cap.
CAlign the throttle cable locating
tape with the cable guide.
DPass through the cable guide
the throttle cable, “ENGINE
STOP” button lead and clutch
cable.
EPass the throttle cable and
clutch cable above the radiator
hose, and pass the “ENGINE
STOP” button lead below the
radiator hose.FInstall the ignition coil, side
core and ground lead together
to the frame.
GClamp the clutch cable to the
left engine bracket. Clamp the
clutch cable below the position-
ing grommet.
HPass the air vent hose back of
the throttle cable.
IPass the air vent hose, over-
flow hose and crankcase
breather hose between the
frame and connecting rod.
1C3-9-30-2B 27/5/04 4:18 PM Page 26

2-15
SPECCABLE ROUTING DIAGRAM
1“ENGINE STOP” button lead
2C.D.I. magneto lead
3Ignition coil lead
4Ground lead
5Positioning tape
6Protection tube
7C.D.I.unit
8Throttle cable
9Clutch cable
0Side core
qRadiator breather hoseAPass the high tension cord to
the left of the radiator hose.
BClamp to the frame the
“ENGINE STOP” button lead
and C.D.I. magneto lead.
Clamp them in front of the radi-
ator fitting boss.
CClamp to the frame the throttle
cable, clutch cable and ignition
coil lead.
DPass the C.D.I. magneto lead
and radiator breather hose
between the frame and the
right side of the radiator.
EInsert the C.D.I. unit band until
it stops at the C.D.I. unit stay.
FPass the C.D.I. magneto lead
and radiator breather hose
between the frame and the
radiator hose.GLocate the clamp ends in the
arrowed range.
1C3-9-30-2B 16/6/04 9:51 AM Page 30

3-1
MAINTENANCE INTERVALS
INSP
ADJ
EC300000
REGULAR INSPECTION AND ADJUSTMENTS
EC310053
MAINTENANCE INTERVALS
The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind
that such factors as weather, terrain, geographical location, and individual usage will alter the required
maintenance and lubrication intervals. If you are a doubt as to what intervals to follow in maintaining
and lubricating your machine, consult your Yamaha dealer.
Item Remarks
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
Inspect crack
Inspect carbon deposits
and eliminate them
Check ring end gap
Inspect carbon deposits
and eliminate them
Check gasket
Inspect score marks
Inspect wear
Inspect carbon deposits
and eliminate them
Inspect housing, friction
plate, clutch plate and
spring
Yamalube 4 (10W-30) or
SAE 10W-30 SE motor oil
Inspect wear
Use chain lube
Chain slack: 48~58 mm
(1.9~2.3 in) PISTON
Inspect and clean

Replace
PISTON RING
Inspect
Replace
PISTON PIN, SMALL END BEARING
Inspect
Replace
CYLINDER HEAD
Inspect and clean
Retighten
CYLINDER
Inspect and clean
Replace
YPVS
Inspect and clean
CLUTCH
Inspect and adjust
Replace
TRANSMISSION
Replace oil
Inspect
Replace bearing
SHIFT FORK, SHIFT CAM, GUIDE BAR
Inspect
ROTOR NUT
Retighten
MUFFLER
Inspect
Clean
Retighten
CRANK
Inspect and clean
CARBURETOR
Inspect, adjust and clean
SPARK PLUG
Inspect and clean
Replace
DRIVE CHAIN
Lubricate, slack, alignment
Replace
1C3-9-30-3A 17/5/04 8:42 PM Page 2

3-2
MAINTENANCE INTERVALS
INSP
ADJ
Item Remarks
COOLING SYSTEM
Check coolant level and leakage
Check radiator cap operation
Replace coolantEvery two years
Inspect hoses
OUTSIDE NUTS AND BOLTS Refer to “STARTING
RetightenAND BREAK-IN” section
in the CHAPTER 1.
AIR FILTER
Clean and lubricateUse foam air-filter oil or
Replaceequivalent oil
FRAME
Clean and inspect
FUEL TANK, COCK
Clean and inspect
BRAKES
Adjust lever position and pedal height
Lubricate pivot point
Check brake disc surface
Check fluid level and leakage
Retighten brake disc bolts, caliper bolts,

master cylinder bolts and union bolts
Replace pads
Replace brake fluidEvery one year
FRONT FORKS
Inspect and adjust
Replace oilSuspension oil “S1”
Replace oil seal
FRONT FORK OIL SEAL AND DUST SEAL
Clean and lubeLithium base grease
PROTECTOR GUIDE
Replace
REAR SHOCK ABSORBER
(After
Inspect and adjustrain ride)
Lube Molybdenum disulfide grease
Retighten
CHAIN GUARD AND ROLLERS
Inspect
SWINGARM
Inspect, lube and retightenMolybdenum disulfide grease
RELAY ARM, CONNECTING ROD
Inspect, lube and retightenMolybdenum disulfide grease
STEERING HEAD
Inspect free play and retighten
Clean and lubeLithium base grease
Replace bearing
TIRE, WHEELS
Inspect air pressure, wheel run-out,

tire wear and spoke looseness
Retighten sprocket bolt
Inspect bearings
Replace bearings
LubricateLithium base grease
THROTTLE, CONTROL CABLE
Check routing and connectionYamaha cable lube or
LubricateSAE 10W-30 motor oil
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
3
1C3-9-30-3A 17/5/04 8:42 PM Page 3

3-3
PROGRAMME D’ENTRETIEN
INSP
ADJ
PartieAprès Chaque Chaque Chaque Si
Remarques
rodage coursetrois- cinquiè- nécessa-
ième me ire
BRAS OSCILLANT
Contrôler, lubrifier et resserrer
66
BRAS RELAIS, BIELLE
Contrôler, lubrifier et resserrer66
TETE DE FOURCHE
Contrôler le jeu66
Nettoyer et lubrifier6
Changer le roulement6
PNEU; ROUES
Contrôler la pression de gonflage,
le voile de roue et l’usure des
66pneus et voir s’il n’y a pas de
rayon détendu
Resserrer les boulons de la roue
66dentée
Contrôler les roulements6
Changer les roulements6
Graisser6
ACCELERATEUR, CABLES DE
COMMANDE
Contrôler le chaminement et le
66branchement
Graisser66
Graisse au bisulfure de
molybdène
Graisse au bisulfure de
molybdène
Graisse à base de lithium
Graisse à base de lithium
Yamaha lube pour câble ou
Huile moteur SAE 10W-30
1C3-9-30-3A 17/5/04 8:42 PM Page 7

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~23
results of test runs before racing? Are inspection and
maintenance completely done?
1C3-9-30-3A 17/5/04 8:42 PM Page 14

3-7
INSP
ADJ
RADIATOR CAP INSPECTION
cC
9Do not mix more than one type of ethyl-
ene glycol antifreeze containing corro-
sion inhibitors for aluminum engine.
9Do not use water containing impurities
or oil.
7. Install:
9Radiator cap
Start the engine and warm it up for a sev-
eral minutes.
8. Check:
9Coolant level
Coolant level low Add coolant.
EC355000
RADIATOR CAP INSPECTION
1. Inspect:
9Seal (radiator cap) 1
9Valve and valve seat 2
Crack/Damage Replace.
Exist fur deposits 3Clean or replace.
Handling notes of coolant:
The coolant is harmful so it should be handled
with special care.
w
9When coolant splashes to your eye.
Thoroughly wash your eye with water
and see your doctor.
9When coolant splashes to your clothes.
Quickly wash it away with water and then
with soap.
9When coolant is swallowed.
Quickly make him vomit and take him to
a doctor.
1C3-9-30-3A 17/5/04 8:42 PM Page 22