2005 YAMAHA YZ125LC fuel

2-13
SPECCABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1Ground lead
2High tension cord
3Grommet
4Air vent hose
5Crankcase breather hose
6Y.P.V.S. breather hose
7Throttle cable
8Clutch cable
9Engine bracket (right)
0Engine bracket (left)
qAir vent hose (left)
wAir vent hose (right)
e“ENGINE STOP” button leadAPass the clutch cable on the
outside of the throttle cable and
“ENGINE STOP” button lead.
BInsert the tip of the fuel tank
breather hose into the hole in
the steering shaft cap.
CAlign the throttle cable locating
tape with the cable guide.
DPass through the cable guide
the throttle cable, “ENGINE
STOP” button lead and clutch
cable.
EPass the throttle cable and
clutch cable above the radiator
hose, and pass the “ENGINE
STOP” button lead below the
radiator hose.FInstall the ignition coil, side
core and ground lead together
to the frame.
GClamp the clutch cable to the
left engine bracket. Clamp the
clutch cable below the position-
ing grommet.
HPass the air vent hose back of
the throttle cable.
IPass the air vent hose, over-
flow hose and crankcase
breather hose between the
frame and connecting rod.
1C3-9-30-2B 27/5/04 4:18 PM Page 26

3-2
MAINTENANCE INTERVALS
INSP
ADJ
Item Remarks
COOLING SYSTEM
Check coolant level and leakage
Check radiator cap operation
Replace coolantEvery two years
Inspect hoses
OUTSIDE NUTS AND BOLTS Refer to “STARTING
RetightenAND BREAK-IN” section
in the CHAPTER 1.
AIR FILTER
Clean and lubricateUse foam air-filter oil or
Replaceequivalent oil
FRAME
Clean and inspect
FUEL TANK, COCK
Clean and inspect
BRAKES
Adjust lever position and pedal height
Lubricate pivot point
Check brake disc surface
Check fluid level and leakage
Retighten brake disc bolts, caliper bolts,

master cylinder bolts and union bolts
Replace pads
Replace brake fluidEvery one year
FRONT FORKS
Inspect and adjust
Replace oilSuspension oil “S1”
Replace oil seal
FRONT FORK OIL SEAL AND DUST SEAL
Clean and lubeLithium base grease
PROTECTOR GUIDE
Replace
REAR SHOCK ABSORBER
(After
Inspect and adjustrain ride)
Lube Molybdenum disulfide grease
Retighten
CHAIN GUARD AND ROLLERS
Inspect
SWINGARM
Inspect, lube and retightenMolybdenum disulfide grease
RELAY ARM, CONNECTING ROD
Inspect, lube and retightenMolybdenum disulfide grease
STEERING HEAD
Inspect free play and retighten
Clean and lubeLithium base grease
Replace bearing
TIRE, WHEELS
Inspect air pressure, wheel run-out,

tire wear and spoke looseness
Retighten sprocket bolt
Inspect bearings
Replace bearings
LubricateLithium base grease
THROTTLE, CONTROL CABLE
Check routing and connectionYamaha cable lube or
LubricateSAE 10W-30 motor oil
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
3
1C3-9-30-3A 17/5/04 8:42 PM Page 3

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~23
results of test runs before racing? Are inspection and
maintenance completely done?
1C3-9-30-3A 17/5/04 8:42 PM Page 14

3-36
STEERING HEAD INSPECTION AND ADJUSTMENT
INSP
ADJ
9Loosen the ring nut one turn.
9Retighten the ring nut using the ring nut
wrench.
w
Avoid over-tightening.
9Check the steering shaft by turning it lock to
lock. If there is any binding, remove the
steering shaft assembly and inspect the
steering bearings.
9Install the plain washer 5, handle crown 6,
plain washer 7, steering shaft nut 8, steer-
ing shaft cap 9, handlebar 0, handlebar
holder q and number plate w.
NOTE:
9The upper handlebar holder should be
installed with the punched mark aforward.
9Install the handlebar so that the marks b
are in place on both sides.
9Insert the end of the fuel breather hose e
into the hole in the steering shaft cap.
cC
First tighten the bolts on the front side of
the handlebar holder, and then tighten the
bolts on the rear side.
Ring nut wrench:
YU-33975/90890-01403
Ring nut (initial tightening):
38 Nm (3.8 m•kg, 27ft•lb)
Steering shaft nut:
145 Nm (14.5 m•kg, 105 t•lb)
Handlebar upper holder:
28 Nm (2.8 m•kg, 20 ft•lb)
Pinch bolt (handle crown):
23 Nm (2.3 m•kg, 17 ft•lb)
Number plate:
7 Nm (0.7 m•kg, 5.1 ft•lb)
Ring nut (final tightening):
7 Nm (0.7 m•kg, 5.1 ft•lb)
1C3-9-30-3B 17/5/04 1:21 PM Page 36

3-39
IGNITION TIMING CHECK
INSP
ADJ
EC372012
IGNITION TIMING CHECK
1. Remove:
9Fuel tank
Refer to “SEAT, FUEL TANK AND SIDE
COVERS” section in the CHAPTER 4.
9Spark plug
9Crankcase cover (left)
2. Attach:
9Dial gauge 1
9Spark plug hole dial stand 2
3. Rotate the magneto rotor 1until the
piston reaches top dead center (TDC).
When this happens, the needle on the dial
gauge will stop and reverse directions even
though the rotor is being turned in the same
direction.
4. Set the dial gauge to zero at TDC.
5. From TDC, rotate the rotor clockwise
until the dial gauge indicates that the
piston is at a specified distance from TDC.
6. Check:
9Ignition timing
Punch mark aon rotor should be aligned
with punch mark bon stator.
Not aligned Adjust.
Dial gauge:
YU-3097/90890-01252
Spark plug hole dial stand:
YU-1256
Ignition timing (B.T.D.C.):
0.48 mm (0.019 in)
1C3-9-30-3B 17/5/04 1:22 PM Page 42

4-1
ENGSEAT, FUEL TANK AND SIDE COVERS
EC400000
ENGINE
EC4R0000
SEAT, FUEL TANK AND SIDE COVERS
Extent of removal Order Part name Q’ty Remarks
SEAT, FUEL TANK AND SIDE
COVERS REMOVAL
Preparation for Turn the fuel cock to “OFF”.
removal Disconnect the fuel hose.
1 Seat 1
2 Air scoop (left and right) 2
3 Fitting band 1 Remove on fuel tank side.
4 Bolt (fuel tank) 2
5 Fuel tank 1
6 Side cover (left) 1
Refer to “REMOVAL POINTS”.
7 Side cover (right) 1
8 Number plate 1
1
4
Extent of removal:1Seat removal2Fuel tank removal
3Side covers removal4Number plate removal
2


 

3
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
19 Nm (1.9 m•kg, 13 ft•lb)
19 Nm (1.9 m•kg, 13 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
1C3-9-30-4A 25/5/04 7:23 PM Page 2

4-2
ENGSEAT, FUEL TANK AND SIDE COVERS
EC4R3000
REMOVAL POINTS
EC413110
Side cover
1. Remove:
9Bolt (side cover)
9Side cover (left and right) 1
NOTE:
Draw the side cover downward to remove it
because its claws aare inserted in the air
cleaner case.
1C3-9-30-4A 25/5/04 7:23 PM Page 4

4-3
ENGEXHAUST PIPE AND SILENCER
EC4S0000
EXHAUST PIPE AND SILENCER
Extent of removal Order Part name Q’ty Remarks
EXHAUST PIPE AND
SILENCER REMOVAL
Preparation for Side cover (right) Refer to “SEAT, FUEL TANK AND
removal SIDE COVERS” section.
1 Bolt (silencer) 2
2 Silencer 1
3 Collar [D=ø10.5 mm (0.41 in)] 1
4 Collar [D=ø10.0 mm (0.39 in)] 1
5 Grommet (front) 1
6 Grommet (rear) 1
7 Tension spring 2
8 Bolt (exhaust pipe) 2
9 Exhaust pipe 1
1
Extent of removal:1Silencer removal2Exhaust pipe removal
2
12 Nm (1.2 m•kg, 8.7 ft•lb)
12 Nm (1.2 m•kg, 8.7 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
12 Nm (1.2 m•kg, 8.7 ft•lb)
2
12 Nm (1.2 m•kg, 8.7 ft•lb)
1C3-9-30-4A 25/5/04 7:23 PM Page 6