2005 YAMAHA YZ125LC coolant

3-8
INSP
ADJRADIATOR CAP OPENING PRESSURE INSPECTION/
COOLING SYSTEM INSPECTION
EC356002
RADIATOR CAP OPENING PRESSURE
INSPECTION
1. Attach:
9Radiator cap tester 1and adapter 2
NOTE:
Apply water on the radiator cap seal.
3Radiator cap
2. Apply the specified pressure.
3. Inspect:
9Pressure
Impossible to maintain the specified pres-
sure for 10 seconds Replace.
EC357003
COOLING SYSTEM INSPECTION
1. Inspect:
9Coolant level
2. Attach:
9Radiator cap tester 1and adapter 2
3. Apply the specified pressure.
Radiator cap tester:
YU-24460-01/90890-01325
Adapter:
YU-33984/90890-01352
Radiator cap tester:
YU-24460-01/90890-01325
Adapter:
YU-33984/90890-01352
Radiator cap opening pressure:
95~125 kPa (0.95~1.25 kg/cm
2,
13.5~17.8 psi)
Standard pressure:
180 kPa (1.8 kg/cm
2, 25.6 psi)
NOTE:
9Do not apply pressure more than specified
pressure.
9Radiator should be filled fully.
1C3-9-30-3A 17/5/04 8:42 PM Page 24

3-9
INSP
ADJ
CLUTCH ADJUSTMENT
4. Inspect:
9Pressure
Impossible to maintain the specified pres-
sure for 10 seconds Repair.
9Radiator 1
9Radiator hose joint 2
Coolant leakage Repair or replace.
9Radiator hose 3
Swelling Replace.
2. Adjust:
9Clutch lever free play
EC359020
CLUTCH ADJUSTMENT
1. Check:
9Clutch lever free play a
Out of specification Adjust.
NOTE:
9Before adjustment, expose the adjuster by
moving the boot 3and cap 4away.
9Make minute adjustment on the lever side
using the adjuster 5.
9After adjustment, check proper operation of
clutch lever.
Clutch lever free play a a
:
8~13 mm (0.31~0.51 in)
Clutch lever free play adjustment steps:
9Loosen the locknut 1.
9Turn the adjuster 2until free play ais with-
in the specified limits.
9Tighten the locknut.
Locknut:
4 Nm (0.4 m•kg, 2.9 ft•lb)
3. Install:
9Cap 1
9Boot 2
NOTE:
Place the tip aof the cap in the boot.
1C3-9-30-3A 17/5/04 8:42 PM Page 26

4-4
ENGRADIATOR
Extent of removal Order Part name Q’ty Remarks
RADIATOR REMOVAL
Preparation for Drain the coolant.
Refer to “COOLANT REPLACEMENT“
removal section in the CHAPTER 3.
Seat and fuel tank Refer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
1 Panel 2
2 Clamp (radiator hose 1, 3) 2 Only loosening.
3 Radiator hose 2 1
4 Radiator (left) 1
5 Radiator hose 4 1
6 Radiator (right) 1
7 Radiator hose 1 1
8 Radiator hose 3 1
9 Radiator breather hose 1
EC450001
RADIATOR
Extent of removal:1Radiator removal
1
10 Nm (1.0 m•kg, 7.2 ft•lb)
1 Nm (0.1 m•kg, 0.7 ft•lb)
1 Nm (0.1 m•kg, 0.7 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-30-4A 25/5/04 7:23 PM Page 8

4-49
ENGWATER PUMP
EC4G3000
REMOVAL POINTS
EC4G3210
Oil seal
NOTE:
9Replace the oil seal when transmission oil or
coolant leaks out from the water pump housing
hole at the bottom.
9Do not reuse the removed bearing and oil seal.
1. Remove:
9Bearing 1
2. Remove:
9Oil seal (outside) 1
9Oil seal (inside) 2
EC4G4000
INSPECTIONEC444200
Impeller shaft assembly
1. Inspect:
9Impeller shaft assembly1
Bend/Wear/Damage Replace.
Fur deposits Clean.
1C3-9-30-4C 25/5/04 7:17 PM Page 26

4-51
ENGWATER PUMP
EC4G5220
Impeller shaft assembly
1. Install:
9Impeller shaft assembly1
NOTE:
9Take care so that the oil seal lip is not dam-
aged or the spring does not slip off its position.
9When installing the impeller shaft assembly,
apply the lithium soap base grease on the oil
seal lip and impeller shaft assembly. And install
the shaft while turning it.
2. Install:
9Plain washer 1
9Dowel pin 2
9Impeller shaft gear 3
9Collar 4
9Plain washer 5
9Circlip 6
NOTE:
Install the Impeller shaft gear with the dowel pin
fitted in the groove ain the same gear.
3. Install:
9Dowel pin 1
9Gasket (water pump housing cover) 2
4. Install:
9Water pump housing cover 1
9Bolt (water pump housing cover) 2
9Copper washer (coolant drain bolt) 3
9Coolant drain bolt 4
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-30-4C 25/5/04 7:18 PM Page 30