2005 YAMAHA YD110 wheel alignment

PREVENTIVE MAINTENANCE SCHEDULE
S.NO.ITEM OPERATION
1. VALVES
2. SPARK PLUG
3 . CARBURETOR
4. AIR FILTER*
5. FUEL LINE
6 . FUEL FILTER
7. ENGINE OIL
8.
9.
10.
11. CLUTCH
12.
1 3 . WHEELS
Check valve clearances, adjust if necessary.
Check condition, gap;
Clean and reset if necessary.
Check idle speed, Choke lever operation.
Clean, inspect & lubricate. (Replace if necessary)
Check fuel hose, for cracks or damage.
Replace if necessary.
Replace with recommended oil - Yamalube SG Grade
(Warm engine before draining)
Wash with petrol
Check operation./Adjust if necessary.
Grease the brake cam.
Check for wear, replace if necessary.
Check alignment marks on Push Lever and
Crankcase L.H. Adjust if necessary.
Check Rear Arm assembly for looseness.
Tighten with specified Torque if necessary.
Check runout, spoke tightness, damage;
Correct it, if necessary.Check for free flow of petrol, cleanliness of filter bowl,
Replace if necessary.
ENGINE OIL
FILTER SCREEN
BRAKE FRONT
& REAR
BRAKE SHOES-
FRONT & REAR
REAR ARM
PIVOT
REPLACE EVERY 10,000 km
•••
••
SERVICE
FREE
PAIDEVERY
2000
KM I-VIVII-VIIIIX-XXI-XV
BONUS
FREEPAID
6.3
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
•••
••
••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
••• •• ••• ••
PG1_55.pmd2/25/2005, 10:04 AM 39

6.4
1 4 . WHEEL BEARING
1 5 . STEERING BEARING
1 6 . FRONT FORKS
17.
1 8 . DRIVE CHAIN
19.
20.
2 1 . BATTERY
22.S.NO.ITEM OPERATION
SERVICE
FREE
PAIDEVERY
2000
KM
Check Bearing assembly for looseness, damage;
Replace if necessary.
Check Bearing assembly for looseness;
Correct if necessary.
Check operation/oil leakage. Repair if necessary.
Check all Chassis fittings and fasteners for looseness
Tighten as per specification.
Check operation and lubricate if necessary.
Check electrolyte level and top it up if necessary.
Check specific gravity and charge if required.
Check breather pipe for blockage and routing.
Check operation, free play, cable damage
Readjust or replace as required.Check chain slack, alignment. Adjust if necessary.
Clean & lubricate periodically.
CONTROL CABLES
-THROTTLE
-CLUTCH
-FRONT BRAKE
EVERY 10,000 km
••• ••
ABSORBER REAR SHOCK
NUTS, BOLTS AND
FASTENERS
CENTERSTAND AND
SIDE STAND
Replace grease
Replace grease
Replace oil
EVERY 10,000 km
EVERY 10,000 km
EVERY MONTH
PREVENTIVE MAINTENANCE SCHEDULE
IT IS RECOMMENDED THAT THE ABOVE BE SERVICED BY AUTHORIZED YMI DEALER.
SERVICE MORE FREQUENTLY WHEN THE VEHICLE IS DRIVEN IN DUSTY AREAS.
I-VIVII-VIIIIX-X XI-XV
BONUS
FREEPAID••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
••• ••
Check operation/oil leakage. Repair if necessary.
*
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
PG1_55.pmd2/25/2005, 10:04 AM 40

1. Chain joint
psu&t¨M
If the chain is disassembled, be
sure the chain lock is placed in the
correct direction when installing.
;fn psu d¨ [k¨y dj vyx dj fn;k
x;k gS r¨ ;g lqfuf'pr djsa fd bls fQj
ls yxkrs le; psu ykWd d¨ lgh fn'kk esa
yxk;k tk,A
1. Adjusting nut
,Mt¯LVx uV
2. Cotter pin
dkWVj fiu
3. Axle nut
,fDly dk uV
Driven chain slack adjustmentMªkbo&psu dh ¼,MtLVesaV½1. Loosen the rear brake pedal
free play adjusting nut.
fiNyh czsd ds iSMy ds Ýh&Iys
,Mt¯LVx uV d¨ 2. Remove the cotter pin from the
axle nut.
,Dly uV ls dkWVj&fiu d¨ vyx
gVk ysaA
3. Loosen the axle nut.
,Dly uV d¨ 6.26
1. Locknut
ykWd uV
2. Adjusting hex screw
,Mt¯LVx gsDl&isap
4. Loosen the chain adjusting
locknuts on each chain puller.
To tighten the chain, turn the
chain adjusting hex screw in
direction(a). To loosen the
chain, turn the chain and push
the wheel forward. Turn each
chain adjusting hex screw
exactly the same amount to
maintain correct axle
alignment. There are marks on
each chain puller. Use these
makes to align the rear wheel.
çR;sd psu&iqyj ij yxs ,Mt¯LVx
ykWd uV¨a ¼isp¨a½ d¨ psu d¨ dlus fy,] psu ,Mt¯LVx
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
12
3ç
è
2
1
pg56_96.pmd2/25/2005, 9:59 AM 62

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd2/25/2005, 10:00 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd2/25/2005, 10:00 AM 10