2005 YAMAHA XTZ125 oil type

6-8
6-8 e.Fill engine with oil. Install the oil filter cap and tighten.
NOTE:
Recommended engine oil classification; API Service “SH”
type or equivalent
Recommended oil:
YAMALUBE 4
Oil quantity:
Total amount:
1.2 L ( 0.264 Imp gal, 0.317 US gal)
Periodic oil change:
1.0 L ( 0.220 Imp gal, 0.264 US gal)
f. Start the engine and warm up for a few minutes. While
warming up, check for oil leakage. If oil leakage is found,
stop the engine immediately, and check for the cause.
g. Stop the engine and check the oil level.
CAUTION:
Be sure no foreign material enters the crankcase.
CAUTION:
Do not put in any chemical additives. Engine oil also
lubricates the clutch and additives could cause clutch
slippage.
After replacing the engine oil, be sure to check the oil
pressure.
CAUTION:
e.Fill engine with oil. Install the oil filter cap and tighten.
NOTE:
Recommended engine oil classification; API Service “SH”
type or equivalent
Recommended oil:
YAMALUBE 4
Oil quantity:
Total amount:
1.2 L ( 0.264 Imp gal, 0.317 US gal)
Periodic oil change:
1.0 L ( 0.220 Imp gal, 0.264 US gal)
f. Start the engine and warm up for a few minutes. While
warming up, check for oil leakage. If oil leakage is found,
stop the engine immediately, and check for the cause.
g. Stop the engine and check the oil level.
CAUTION:
Be sure no foreign material enters the crankcase.
CAUTION:
Do not put in any chemical additives. Engine oil also
lubricates the clutch and additives could cause clutch
slippage.
After replacing the engine oil, be sure to check the oil
pressure.
CAUTION:

6-23
6-23 3. Refill with the same type of brake fluid. Mixing fluids
may result in a harmful reaction and lead to poor brake
performance.
4. Be careful that water does not enter the master cylinder
when refilling. Water will significantly lower the boiling
point of the fluid and may result in vapor lock.
5. Brake fluid may deteriorate painted surfaces or plastic
parts. Always clean up spilled fluid immediately.
6. Have a Yamaha dealer check the cause if the brake
fluid level goes down.1. Complete fluid replacement should be done only by
trained service personnel.
2. Have a Yamaha dealer replace the following
components during periodic maintenance or when they
are damaged or leaking.
a. Replace all rubber seals every two years.
b. Replace all hoses every four years. Brake fluid replacement
3. Refill with the same type of brake fluid. Mixing fluids
may result in a harmful reaction and lead to poor brake
performance.
4. Be careful that water does not enter the master cylinder
when refilling. Water will significantly lower the boiling
point of the fluid and may result in vapor lock.
5. Brake fluid may deteriorate painted surfaces or plastic
parts. Always clean up spilled fluid immediately.
6. Have a Yamaha dealer check the cause if the brake
fluid level goes down.1. Complete fluid replacement should be done only by
trained service personnel.
2. Have a Yamaha dealer replace the following
components during periodic maintenance or when they
are damaged or leaking.
a. Replace all rubber seals every two years.
b. Replace all hoses every four years. Brake fluid replacement

6-26
6-26Cable inspection and lubrication Drive chain lubrication
The chain consists of many parts which work with each
other. If the chain is not maintained properly, it will wear out
quickly. Therefore, the chain must be serviced regularly.
This service is especially necessary when riding in dusty
areas.
1. Use Yamaha Chain and Cable Lube or any brands of
spray-type chain lubricant. First, remove all dirt and mud
from the chain with a brush or cloth, then spray lubricant
between both rows of side plates and on all center
rollers. The chain should be lubricated every 500 km
(300 mi).
2. To clean the chain, remove it from the machine, dip it
in solvent, and clean out as much dirt as possible. Take
the chain out of the solvent and dry it. Immediately
lubricate the chain to prevent it from rusting.Damage to the outer housing of cables may allow
internal rusting and cause interfere with cable
movement. Replace damaged cables as soon as
possible to prevent unsafe conditions.
Lubricate the inner cable and the cable end. If it does not
operate smoothly, ask a Yamaha dealer to replace them.
RECOMMENDED LUBRICANT:
Engine oil SAE 20W50
WARNING:
Cable inspection and lubrication Drive chain lubrication
The chain consists of many parts which work with each
other. If the chain is not maintained properly, it will wear out
quickly. Therefore, the chain must be serviced regularly.
This service is especially necessary when riding in dusty
areas.
1. Use Yamaha Chain and Cable Lube or any brands of
spray-type chain lubricant. First, remove all dirt and mud
from the chain with a brush or cloth, then spray lubricant
between both rows of side plates and on all center
rollers. The chain should be lubricated every 500 km
(300 mi).
2. To clean the chain, remove it from the machine, dip it
in solvent, and clean out as much dirt as possible. Take
the chain out of the solvent and dry it. Immediately
lubricate the chain to prevent it from rusting.Damage to the outer housing of cables may allow
internal rusting and cause interfere with cable
movement. Replace damaged cables as soon as
possible to prevent unsafe conditions.
Lubricate the inner cable and the cable end. If it does not
operate smoothly, ask a Yamaha dealer to replace them.
RECOMMENDED LUBRICANT:
Engine oil SAE 20W50
WARNING:

8-1
8-1
SPECIFICATIONS
MODEL
Dimension:
Overall length
Overall width
Overall height
Seat height
Wheet base
Minimum ground clearance
Basic weight:
With oil and without fuel:
Minimum turning radius:
Engine:
Type
Cylinder arrangement
Displacement
Bore x Stroke
Compression rate
Starting system
Lubrification system
103 Kg (227 lb)
113 Kg (249 lb) 2.090 mm (82.3 in)
810 mm (31.9 in)
1.125 mm (44.3 in)
840 mm (33.1 in)
1.340 mm (52.7 in)
265 mm (10.4 in)
2.100 mm (82.7 in)
XTZ 125K
Air cooled, 4-stroke
gasoline, SOHC
Single cylinder
123.7 cm
3
54 x 54 mm (2.13 x 2.13 in)
10.0 : 1
Kick starter
Wet sump
104 Kg (229 lb)
114 Kg (251 lb) 2.090 mm (82.3 in)
810 mm (31.9 in)
1.125 mm (44.3 in)
840 mm (33.1 in)
1.340 mm (52.7 in)
265 mm (10.4 in)
2.100 mm (82.7 in)
XTZ 125E
Air cooled, 4-stroke
gasoline, SOHC
Single cylinder
123.7 cm
3
54 x 54 mm (2.13 x 2.13 in)
10.0 : 1
Electric starter
Wet sump
SPECIFICATIONS
MODEL
Dimension:
Overall length
Overall width
Overall height
Seat height
Wheet base
Minimum ground clearance
Basic weight:
With oil and without fuel:
Minimum turning radius:
Engine:
Type
Cylinder arrangement
Displacement
Bore x Stroke
Compression rate
Starting system
Lubrification system
103 Kg (227 lb)
113 Kg (249 lb) 2.090 mm (82.3 in)
810 mm (31.9 in)
1.125 mm (44.3 in)
840 mm (33.1 in)
1.340 mm (52.7 in)
265 mm (10.4 in)
2.100 mm (82.7 in)
XTZ 125K
Air cooled, 4-stroke
gasoline, SOHC
Single cylinder
123.7 cm
3
54 x 54 mm (2.13 x 2.13 in)
10.0 : 1
Kick starter
Wet sump
104 Kg (229 lb)
114 Kg (251 lb) 2.090 mm (82.3 in)
810 mm (31.9 in)
1.125 mm (44.3 in)
840 mm (33.1 in)
1.340 mm (52.7 in)
265 mm (10.4 in)
2.100 mm (82.7 in)
XTZ 125E
Air cooled, 4-stroke
gasoline, SOHC
Single cylinder
123.7 cm
3
54 x 54 mm (2.13 x 2.13 in)
10.0 : 1
Electric starter
Wet sump

8-2
8-2
MODEL XTZ 125E and XTZ 125K
Engine oil:
Air filter:
Fuel:
Type
Tank capacity
Reserve amount
Carburetor:
Type / manufacturer
Spark plug:
Type / manufacturer
Gap
Clutch type: Capacity:
Periódic oil change
Total amount
TypeYAMALUBE 4 or SAE 20W50 type SH
Wet type element
CR7HSA / NGK or U22FSR-U / DENSO
0.7 mm (0.028 in)
Wet, multi-disc Regular unleaded gasoline
10,6
l ( 2.33 Imp gal, 2.80 US gal)
1,0
l ( 0.220 Imp gal, 0.264 US gal) 1,0
l ( 0,220 Imp gal, 0.264 US gal)
1,2 l ( 0,264 Imp gal, 0.317 US gal)
VM 20SS / Mikuni
MODELXTZ 125E and XTZ 125K
Engine oil:
Air filter:
Fuel:
Type
Tank capacity
Reserve amount
Carburetor:
Type / manufacturer
Spark plug:
Type / manufacturer
Gap
Clutch type: Capacity:
Periódic oil change
Total amount
TypeYAMALUBE 4 or SAE 20W50 type SH
Wet type element
CR7HSA / NGK or U22FSR-U / DENSO
0.7 mm (0.028 in)
Wet, multi-disc Regular unleaded gasoline
10,6
l ( 2.33 Imp gal, 2.80 US gal)
1,0 l ( 0.220 Imp gal, 0.264 US gal) 1,0
l ( 0,220 Imp gal, 0.264 US gal)
1,2 l ( 0,264 Imp gal, 0.317 US gal)
VM 20SS / Mikuni

8-4
8-4
MODEL
Brakes:
Front brake type
Operation
Rear brake type
Operation
Shock absorber:
Front
Rear
Wheel travel
Front
Rear Suspension:
Front
Rear
Electrical:
Ignition system
Generator system
Battery type / capacity
XTZ 125E and XTZ 125K
Coil spring, Oil damper
Gas, Coil spring. Oil damper
180 mm (7.1 in)
180 mm (7.1 in) Telescopic fork
Swingarm (New monocross suspension)
C.D.I.
AC Magneto generator
YB5L-B/ 12V 5.0 Ah
Single, Disc brake
Right hand operation
Drum brake
Right foot operation
MODEL
Brakes:
Front brake type
Operation
Rear brake type
Operation
Shock absorber:
Front
Rear
Wheel travel
Front
Rear Suspension:
Front
Rear
Electrical:
Ignition system
Generator system
Battery type / capacity
XTZ 125E
Coil spring, Oil damper
Gas, Coil spring. Oil damper
180 mm (7.1 in)
180 mm (7.1 in) Telescopic fork
Swingarm (New monocross suspension)
C.D.I.
AC Magneto generator
YB5L-B/ 12V 5.0 Ah
Single, Disc brake
Right hand operation
Drum brake
Right foot operation