2005 YAMAHA VX CRUISER ECU

3-11
E
EJU21240
Fire extinguisher
Check that there is a full fire extinguisher
on board. The fire extinguisher holder and
cover 1 are located in the front storage
compartment.
To store the fire extinguisher, unhook the
band 2 and remove the cover. Place the fire
extinguisher in the holder, and then place
the cover over the fire extinguisher. Fasten
the cover and the fire extinguisher with the
band securely.
NOTE:@
See the instructions supplied by the fire
extinguisher manufacturer for checking
the fire extinguisher. Always keep the
extinguisher secured in the holder with its
cover in place.

Always carry a fire extinguisher on board.
A fire extinguisher is not standard equip-
ment with this watercraft. If you do not
have one, contact a Yamaha dealer or a
fire extinguisher dealer to obtain one
meeting the proper specifications.
@
EJU18340
Throttle
Squeeze and release the throttle lever
several times to make sure that there is no
hesitation in its travel. It should be smooth
over the complete range, and spring back to
the idle position when released.
WARNING@ Before starting the engine, always check
the operation of the throttle lever.
@
UF1K70.book Page 11 Friday, November 19, 2004 2:42 PM

3-15
E
EJU18360
Operation
WARNING@ Before operating your watercraft,
become familiar with all controls. Con-
sult your Yamaha dealer about any con-
trol or function you do not fully
understand. Failure to understand how
controls work could cause an accident or
prevent you from avoiding an accident.
@
CAUTION:@ Make sure that the stern drain plugs are
securely tightened before launching the
watercraft.
@
EJU18072
Engine break-in
The engine break-in period is essential to
allow the various components of the engine
to wear and polish themselves to the correct
operating clearances. This ensures proper
performance and promotes longer compo-
nent life.
CAUTION:@ Be sure to check the engine oil level
before operating the watercraft for the
first time. (See page 3-7 for engine oil
checking procedures.)
@
1. Launch the watercraft and start the
engine. (See page 3-17 for engine start-
ing procedures.)
UF1K70.book Page 15 Friday, November 19, 2004 2:42 PM

3-16
E
2. For the first 5 minutes, run the engine at
trolling speed only. For the 30 minutes of
operation after that, keep the engine
speed below 5,000 r/min. For the 1 hour
of operation after that, keep the engine
speed below 6,500 r/min.
3. Proceed with normal operation.
CAUTION:@ Failure to follow the engine break-in pro-
cedure could result in reduced engine
life or even severe engine damage.
@
EJU21650
Launching the watercraft
When launching the watercraft, make
sure that there are no obstructions around
you.
If there are waves, someone should make
sure that the watercraft is not pushed into
the trailer after launching the watercraft.

For VX110 Deluxe
Use the remote control transmitter to
select the unlock mode. (See page 2-16
for Yamaha Security System and
low-RPM mode selection procedures.)
After the watercraft is in the water, start
the engine. Shift into reverse and slowly
move away from the launching area.

For VX110 Sport
After the watercraft is in the water, turn it
around so the bow faces the direction you
want to go. Start the engine, and then
slowly move away from the launching
area.
UF1K70.book Page 16 Friday, November 19, 2004 2:42 PM

3-17
E
EJU20841
Starting the engine
WARNING@ Never start the engine or let it run for any
length of time in an enclosed area.
Exhaust fumes contain carbon monox-
ide, a colorless, odorless gas that may
cause loss of consciousness and death
within a short time. Always operate the
watercraft in an open area.
@
1. If the lock mode of the Yamaha Security
System is selected (for VX110 Deluxe),
use the remote control transmitter to
select the unlock mode. (See page 2-15
for Yamaha Security System and low-
RPM mode selection procedures.)
2. Launch the watercraft in water free from
weeds and debris and at least 60 cm
(2 ft) deep.
WARNING@ Never operate in water that is less than
60 cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged
object, which could result in injury.
@
CAUTION:@ Never operate in water that is less than
60 cm (2 ft) deep, otherwise pebbles or
sand could be sucked into the jet intake,
causing impeller damage or engine over-
heating.
@
UF1K70.book Page 17 Friday, November 19, 2004 2:42 PM

3-19
E
EJU10660
Stopping the engine
To stop the engine, release the throttle
lever, and then push the engine stop switch
(red button).
WARNING@ You need throttle to steer. Shutting off
the engine can cause you to hit an obsta-
cle you are attempting to avoid. A colli-
sion could result in severe injury or
death.
@
EJU21250
Leaving the watercraft
If leaving the watercraft, select the lock
mode of the Yamaha Security System (for
VX110 Deluxe) and remove the engine shut-
off cord to reduce the chance of accidental
starting or unauthorized use by children or
others. (See page 2-15 for Yamaha Security
System and low-RPM mode selection pro-
cedures.)
UF1K70.book Page 19 Friday, November 19, 2004 2:42 PM

3-25
E
EJU21130
Boarding with passengers
WARNING@ Severe internal injuries can occur if
water is forced into body cavities as a
result of being near the jet thrust nozzle.
Do not apply throttle until the passen-
gers are seated with their feet on the
floor of the footwell and are securely
holding on to the person in front of them
or to the handgrip provided.
@
1. Climb on board as noted in the previous
section, and sit astride the seat. Attach
the engine shut-off cord to your left wrist,
and then install the clip to the engine
shut-off switch.
2. Have the passenger move to the rear of
the watercraft.
3. Have the passenger get on board and sit
on the seat. If a second passenger is
getting on, have him or her follow the
same procedure.
NOTE:@ When a passenger is getting on board, both
he and the operator should try to balance
the watercraft.
@
4. The operator should check to see that
the passengers have their feet on the
floor of the footwell and that they are
securely holding on to the person in front
of them or to the handgrip provided.
5. Start the engine, look in all directions,
and then accelerate to planing speed.
WARNING@ Before starting off, make sure that there
are no boats, obstructions, or swimmers
around you.
@
UF1K70.book Page 25 Friday, November 19, 2004 2:42 PM

3-36
E
EJU18111
Transporting
When transporting the watercraft on a
trailer, secure the tie downs to the trailer
through the bow eye and stern eye.
CAUTION:@
Do not route ropes or tie downs over
the seat, as they may leave permanent
marks on the seat’s surface. Also,
wrap the ropes or tie downs with tow-
els or rags where they touch the body
of the watercraft to avoid scratches or
damage.

For VX110 Deluxe:
Before putting the watercraft on the
trailer or transporting it, be sure to put
the shift lever in the forward position,
otherwise the reverse gate may hit an
obstruction, which may cause dam-
age.
@
UF1K70.book Page 36 Friday, November 19, 2004 2:42 PM

4-2
E
1. Put the watercraft on land in a horizontal
position.
2. Remove the seat. (See page 2-5 for seat
removal and installation procedures.)
3. Remove the flushing hose connector
cap1, and then insert the garden hose
adapter 2 into the flushing hose con-
nector 3 and turn it until it is securely
connected.
4. Connect the garden hose adapter to a
water tap using a hose.
5. Start the engine, and then immediately
turn the water supply on until water flows
out continually from the jet nozzle.
6. Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn
the water supply off immediately and
repeat the above steps.
7. Turn the water supply off, and then force
the remaining water out from the cooling
passages by alternately squeezing and
releasing the throttle lever for 10 to
15 seconds.
8. Stop the engine.
9. Remove the garden hose adapter and
install the cap.
UF1K70.book Page 2 Friday, November 19, 2004 2:42 PM