2005 YAMAHA DT125R brake light

SAFETY INFORMATION.....................1-1
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments .................2-3
INSTRUMENTS AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator and warning lights .............3-2
Speedometer unit .............................3-3
Handlebar switches ..........................3-3
Clutch lever .......................................3-4
Shift pedal.........................................3-4
Brake lever ........................................3-5
Brake pedal.......................................3-5
Fuel tank cap ....................................3-5
Catalytic converter............................3-6
2-stroke engine oil ............................3-7
Fuel cock ..........................................3-7
Starter (choke) lever..........................3-8
Seat...................................................3-8
Shock absorber ................................3-9
YEIS handling precautions ...............3-9
YPVS .................................................3-9
Sidestand ........................................3-10
Ignition circuit cut-off system .........3-10
PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2OPERATION AND IMPORTANT RIDING
POINTS................................................5-1
Starting a cold engine ......................5-1
Starting a warm engine ....................5-2
Shifting ..............................................5-2
Engine break-in.................................5-2
Parking ..............................................5-3
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Owner’s tool kit .................................6-1
Periodic maintenance and
lubrication chart ............................6-2
Removing and installing cowlings
and panels .....................................6-5
Checking the spark plug ..................6-6
Transmission oil ................................6-7
Coolant .............................................6-8
Cleaning the air filter element
and check hose ...........................6-10
Ajusting the carburetor ...................6-11
Adjusting the engine idling
speed...........................................6-12
Ajusting the throttle cable free
play ..............................................6-12
Tires ................................................6-13
Spoke wheels .................................6-15
Adjusting the clutch lever free
play ..............................................6-15
Adjusting the brake lever free
play ..............................................6-16Adjusting the brake pedal position
and free play................................6-17
Adjusting the rear brake light
switch ..........................................6-17
Checking the front and rear
brake pads ..................................6-18
Changing the brake fluid ................6-19
Checking the drive chain slack ......6-19
Adjusting the drive chain slack.......6-20
Lubricating the drive chain .............6-20
Checking and lubricating the
cables ..........................................6-21
Checking and lubricating the
throttle grip and cable .................6-21
Adjusting the autolube pump .........6-21
Checking and lubricating the
brake and shift pedals.................6-21
Checking and lubricating the
breake and clutch levers .............6-21
Checking and lubricating the
sidestand .....................................6-21
Checking the front fork ...................6-22
Checking the steering.....................6-22
Checking the wheel bearings .........6-23
Replacing the fuse ..........................6-24
Replacing the headlight bulb..........6-24
Replacing the tail/brake light
bulb .............................................6-25
Replacing the turn signal light
bulb .............................................6-26
Supporting the motorcycle .............6-26
TABLE OF CONTENTS
1D0-F8199-E2.qxd 20/9/04 11:32 Página 4

Control cables• Make sure that operation is smooth.
6-21• Lubricate if necessary.
• Check chain slack.
Drive chain• Adjust if necessary.
6-19/6-20
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
Wheels and tires• Check tire condition and tread depth.
6-13
• Check air pressure.
• Correct if necessary.
Brake and shift pedals• Make sure that operation is smooth.
6-21
• Lubricate pedal pivoting points if necessary.
Brake and clutch levers• Make sure that operation is smooth.
6-21
• Lubricate lever pivoting points if necessary.
Sidestand• Make sure that operation is smooth.
6-21
• Lubricate pivot if necessary.
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
–
• Tighten if necessary.
Instruments, lights,• Check operation.
–
signals and switches• Correct if necessary.
Engine stop switch• Check operation.3-3
Sidestand switch• Check operation of ignition circuit cut-off system.
3-11
• If system is defective, have Yamaha dealer check vehicle.
PRE-OPERATION CHECKS
4-3
4
1D0-F8199-E2.qxd 20/9/04 11:32 Página 26

ODOMETER READING (x 1000 Km) ANNUAL
CHECK
NoITEM CHECK OR MAINTENANCE JOB 1 6 12 18 24
22Transmission oil• Check oil level.√√ √ √√ √• Change.√√
23 *Cooling system• Check coolant level and vehicle for coolant leakage.√√√√ √• Change. Every 3 years
24 *Front and rear
• Check operation.√√ √ √√ √
brake switches
25Moving parts and cables• Lubricate.√√√√ √
Throttle grip • Check operation and free play.
26 * •Adjust the throttle cable free play if necessary.√√√√ √
housing and cable
• Lubricate the throttle grip housing and cable.
27 *Muffler and exhaust pipe• Check the screw clamp for looseness.√√ √ √√
28 *Lights, signals • Check operation.
and switches• Adjust headlight beam.√√ √ √√ √
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
EAU18670
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the bra-
ke fluid.
• Replace the brake hoses every four years and if cracked or damaged.
1D0-F8199-E2.qxd 20/9/04 11:32 Página 35

EAU22192
Adjusting the brake pedal
position and free play
1. Footrest
(a) Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
positioned approximately 12-15 mm
(0,47-0,49 in) below the top of the
footrest. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.
1. Loosen the locknut at the brake
pedal.2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
The brake pedal free play should
measure 10-15 mm (0,34-0,59 in) as
shown. Periodically check the brake
pedal free play and, if necessary,
adjust it as follows.
To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10680
s s
WARNING
After adjusting the drive chain
slack or removing and installing
the rear wheel, always check
the brake pedal free play.
If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this
adjustment.
After adjusting the brake pedal
free play, check the operation
of the brake light.
EAU22270
Adjusting the rear brake light
switch
1. Brake light swicht
2. Adjusting nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
1
1
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 48

Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22340
Checking the front and rear
brake pads
1. Wear limit indicator
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart. To check the
brake pad wear, measure the lining
thickness. If the lining thickness is
less than 0,8 mm (0,03 in), have a
Yamaha dealer replace the brake
pads as a set.
EWA10250
s s
WARNING
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
1. Wear indicator
EAU22580
Checking the brake fluid level
1. Minimum level mark
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the
brake fluid reservoir is level.
1. Minimum level mark

Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
FRONTREAR
FRONTREAR
11
11
1D0-F8199-E2.qxd 20/9/04 11:32 Página 49

This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, replace it as follows.
1. Remove cowling A. (See page
6-5.)
2. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.
3. Remove the headlight bulb hol-
der according to the following
illustration, and then remove the
defective bulb.
NOTE:
The removal procedure depends on
the type of bulb holder installed on
your vehicle.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Place a new bulb into position,
and then secure it with the bulb
holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
5. Install the bulb cover, and then
connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb
1. Screw (x2)
2. Lens
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
21
1D0-F8199-E2.qxd 20/9/04 11:32 Página 56

EAU26000
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appearan-
ce of a motorcycle. Frequent and pro-
per care does not only comply with
the terms of the warranty, but it will
also keep your motorcycle looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-
ducts onto seals, gaskets, sproc-
kets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770
CAUTION
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
7
MOTORCYCLE CARE AND STORAGE
7-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 63

Charging system
AC magneto
BatteryModel
GT6B-3
Voltage, capacity
12 V, 6.0 Ah
HeadlightBulb type
Halogen bulb
Bulb voltage, wattage x quantityHeadlight
12 V, 600 W/55.0 W x 1
Tail/brake light
12 V, 21.0 W/5.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
Auxiliary light
12 V, 5.0 W x 1
Meter lighting
LED
Neutral indicator light
12 V, 3.0 W x 1
High beam indicator light
12 V, 3.0 W x 1
Oil level warning light
12 V, 3.0 W x 1
Turn signal indicator light
12 V, 3.0 W x 1
FusesMain fuse
15.0 A
8
SPECIFICATIONS
8-3
1D0-F8199-E2.qxd 20/9/04 11:32 Página 69