2005 YAMAHA DT125R lights

ODOMETER READING (x 1000 Km) ANNUAL
CHECK
NoITEM CHECK OR MAINTENANCE JOB 1 6 12 18 24
22Transmission oil• Check oil level.√√ √ √√ √• Change.√√
23 *Cooling system• Check coolant level and vehicle for coolant leakage.√√√√ √• Change. Every 3 years
24 *Front and rear
• Check operation.√√ √ √√ √
brake switches
25Moving parts and cables• Lubricate.√√√√ √
Throttle grip • Check operation and free play.
26 * •Adjust the throttle cable free play if necessary.√√√√ √
housing and cable
• Lubricate the throttle grip housing and cable.
27 *Muffler and exhaust pipe• Check the screw clamp for looseness.√√ √ √√
28 *Lights, signals • Check operation.
and switches• Adjust headlight beam.√√ √ √√ √
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
EAU18670
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the bra-
ke fluid.
• Replace the brake hoses every four years and if cracked or damaged.
1D0-F8199-E2.qxd 20/9/04 11:32 Página 35

This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, replace it as follows.
1. Remove cowling A. (See page
6-5.)
2. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.
3. Remove the headlight bulb hol-
der according to the following
illustration, and then remove the
defective bulb.
NOTE:
The removal procedure depends on
the type of bulb holder installed on
your vehicle.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Place a new bulb into position,
and then secure it with the bulb
holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
5. Install the bulb cover, and then
connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb
1. Screw (x2)
2. Lens
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
21
1D0-F8199-E2.qxd 20/9/04 11:32 Página 56

EAU26000
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appearan-
ce of a motorcycle. Frequent and pro-
per care does not only comply with
the terms of the warranty, but it will
also keep your motorcycle looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-
ducts onto seals, gaskets, sproc-
kets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770
CAUTION
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
7
MOTORCYCLE CARE AND STORAGE
7-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 63

AAdjusting the autolube pump ..................6-21
Adjusting the brake lever free play ..........6-16
Adjusting the brake pedal position and
free play .................................................6-17
Adjusting the clutch lever free play .........6-15
Adjusting the drive chain slack ................6-20
Adjusting the engine idling speed ...........6-12
Adjusting the rear brake light switch .......6-17
Ajusting the carburetor ............................6-11
Ajusting the throttle cable free play .........6-12
BBrake lever .................................................3-5
Brake pedal ................................................3-5
CCare............................................................7-1
Catalytic converter .....................................3-6
Changing the brake fluid..........................6-19
Checking and lubricating the brake and
shift pedals ............................................6-21
Checking and lubricating the breake and
clutch levers...........................................6-21
Checking and lubricating the cables .......6-21
Checking and lubricating the sidestand ..6-21
Checking and lubricating the throttle grip
and cable ...............................................6-21
Checking the drive chain slack ................6-19
Checking the front and rear brake
pads .......................................................6-18
Checking the front fork ............................6-22
Checking the spark plug ............................6-6
Checking the steering ..............................6-22
Checking the wheel bearings ..................6-23Cleaning the air filter element and check
hose .......................................................6-10
Clutch lever ................................................3-4
Controls and instruments ..........................2-3
Coolant.......................................................6-8
D2-stroke engine oil .....................................3-7
EEngine break-in ..........................................5-2
FFront wheel ..............................................6-26
Fuel cock....................................................3-7
Fuel tank cap .............................................3-5
H
Handlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-10
Indicator and warning lights ......................3-2
LLeft view .....................................................2-1
Lubricating the drive chain ......................6-20
MMain switch/steering lock ..........................3-1
OOwner’s tool kit ..........................................6-1
PParking .......................................................5-3
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear wheel ...............................................6-28Removing and installing cowlings and
panels ......................................................6-5
Replacing the fuse ...................................6-24
Replacing the headlight bulb ...................6-24
Replacing the tail/brake light bulb ...........6-25
Replacing the turn signal light bulb .........6-26
Right view ..................................................2-2
SSeat ............................................................3-8
Shift pedal ..................................................3-4
Shifting .......................................................5-2
Shock absorber..........................................3-9
Sidestand .................................................3-10
Specifications.............................................8-1
Speedometer unit ......................................3-3
Spoke wheels...........................................6-15
Starter (choke) lever ...................................3-8
Starting a cold engine ................................5-1
Starting a warm engine ..............................5-2
Storage.......................................................7-3
Supporting the motorcycle ......................6-26
TTires .........................................................6-13
Transmission oil .........................................6-7
Troubleshooting .......................................6-29
YYEIS handling precautions.........................3-9
YPVS ..........................................................3-9
INDEX
1D0-F8199-E2.qxd 20/9/04 11:32 Página 72