2005 YAMAHA DT125R warning light

SAFETY INFORMATION.....................1-1
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments .................2-3
INSTRUMENTS AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator and warning lights .............3-2
Speedometer unit .............................3-3
Handlebar switches ..........................3-3
Clutch lever .......................................3-4
Shift pedal.........................................3-4
Brake lever ........................................3-5
Brake pedal.......................................3-5
Fuel tank cap ....................................3-5
Catalytic converter............................3-6
2-stroke engine oil ............................3-7
Fuel cock ..........................................3-7
Starter (choke) lever..........................3-8
Seat...................................................3-8
Shock absorber ................................3-9
YEIS handling precautions ...............3-9
YPVS .................................................3-9
Sidestand ........................................3-10
Ignition circuit cut-off system .........3-10
PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2OPERATION AND IMPORTANT RIDING
POINTS................................................5-1
Starting a cold engine ......................5-1
Starting a warm engine ....................5-2
Shifting ..............................................5-2
Engine break-in.................................5-2
Parking ..............................................5-3
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Owner’s tool kit .................................6-1
Periodic maintenance and
lubrication chart ............................6-2
Removing and installing cowlings
and panels .....................................6-5
Checking the spark plug ..................6-6
Transmission oil ................................6-7
Coolant .............................................6-8
Cleaning the air filter element
and check hose ...........................6-10
Ajusting the carburetor ...................6-11
Adjusting the engine idling
speed...........................................6-12
Ajusting the throttle cable free
play ..............................................6-12
Tires ................................................6-13
Spoke wheels .................................6-15
Adjusting the clutch lever free
play ..............................................6-15
Adjusting the brake lever free
play ..............................................6-16Adjusting the brake pedal position
and free play................................6-17
Adjusting the rear brake light
switch ..........................................6-17
Checking the front and rear
brake pads ..................................6-18
Changing the brake fluid ................6-19
Checking the drive chain slack ......6-19
Adjusting the drive chain slack.......6-20
Lubricating the drive chain .............6-20
Checking and lubricating the
cables ..........................................6-21
Checking and lubricating the
throttle grip and cable .................6-21
Adjusting the autolube pump .........6-21
Checking and lubricating the
brake and shift pedals.................6-21
Checking and lubricating the
breake and clutch levers .............6-21
Checking and lubricating the
sidestand .....................................6-21
Checking the front fork ...................6-22
Checking the steering.....................6-22
Checking the wheel bearings .........6-23
Replacing the fuse ..........................6-24
Replacing the headlight bulb..........6-24
Replacing the tail/brake light
bulb .............................................6-25
Replacing the turn signal light
bulb .............................................6-26
Supporting the motorcycle .............6-26
TABLE OF CONTENTS
1D0-F8199-E2.qxd 20/9/04 11:32 Página 4

EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10550
ON
All electrical circuits are supplied with
power, the meter lighting, taillight,
license plate light and auxiliary lights
come on, and the engine can be star-
ted. The key cannot be removed.
NOTE:
The headlights come on automatically
when the engine is started and stay
on until the key is turned to “OFF”,
even if the engine stalls.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10680
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.
T
o unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
EWA10060
s s
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the vehi-
cle is stopped before turning the
key to “OFF” or “LOCK”.
ONOFF
PUSHLOCKIGNITION
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 15

EAU11002
Indicator and warning lights
1. Turn signal indicator light “b”
2. Dimmer indicator light “j”
3. Neutral indicator light “N”
4. Oil level warning light “z”
EAU11030
Turn signal indicator lights “c” and
“d”
The corresponding indicator light flas-
hes when the turn signal switch is
pushed to the left or right.
EAU11070
Neutral indicator light “N”
This indicator light comes on when
the transmission is in the neutral posi-
tion.
EAU11080
High beam indicator light “j”
This indicator light comes on when
the high beam of the headlight is swit-
ched on.
EAU11180
Oil level warning light “z”
This warning light comes on when the
key is in the “ON” position or when
the oil level in the 2-stroke engine oil
tank is low during operation. If the
warning light comes on during opera-
tion, stop immediately and fill the oil
tank with Yamalube 2 or equivalent 2-
stroke engine oil of either JASO grade
“FC” or ISO grades “EG-C” or “EG-
D”. The warning light should go off
after the 2-stroke engine oil tank has
been refilled.
NOTE:
If the warning light does not come on
when the key is in the “ON” position
or does not go off after the 2-stroke
engine oil tank has been refilled, have
a Yamaha dealer check the electrical
circuit.
ECA10010
CAUTION
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
EAU11430
Coolant temperature warning light
“y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
ECA10020
CAUTION
Do not operate the engine if it is
overheated.
0km/h406080
100
120
130 20
y
00001
5
0008
bj
zN
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
1
234
1D0-F8199-E2.qxd 20/9/04 11:32 Página 16

EAU11640
Speedometer unit
1. Odometer
2. Tripmeter
3. Reset button
4. Coolant temperature warning lamp
The speedometer unit is equipped
with a speedometer, an odometer and
a tripmeter. The speedometer shows
riding speed. The odometer shows
the total distance traveled. The trip-
meter shows the distance traveled
since it was last set to zero with the
reset knob. The tripmeter can be used
to estimate the distance that can be
traveled with a full tank of fuel. This
information will enable you to plan
future fuel stops.
NOTE:
Only for the German model equipped
with a speed limiter:
The speed limiter prevents the vehicle
from exceeding a riding speed of 80
km/h.
EAU12343
Handlebar switches
1. Dimmer switch “j/k”
2. Horn switch “a”
3. Turn signal switch “c/d”
4. Hazard switch “ ”
EAU12400
Dimmer switch “j/k”
Set this switch to “j” for the high
beam and to “k” for the low beam.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “d”. To signal a left-hand
turn, push this switch to “c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAU12660
Engine stop switch “f/e”
1. Stop switch “f/e”
2. Start switch “g”
Set this switch to “f” before starting
the engine. Set this switch to “e” to
0km
/h406080
100
120
130 20
y
00001
5
0008
bj
zN
3
INSTRUMENT AND CONTROL FUNCTIONS
3-3
1
23
4
1
2 41
3
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 17

EAU15950
EWA10270
s s
WARNING
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thoroughly
understand.
Never start the engine or ope-
rate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of cons-
ciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised comple-
tely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU16060
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-11.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch
is set to “f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-8.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION
For maximum engine life, never
accelerate hard when the engine is
cold!
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 29

EAU22192
Adjusting the brake pedal
position and free play
1. Footrest
(a) Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
positioned approximately 12-15 mm
(0,47-0,49 in) below the top of the
footrest. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.
1. Loosen the locknut at the brake
pedal.2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
The brake pedal free play should
measure 10-15 mm (0,34-0,59 in) as
shown. Periodically check the brake
pedal free play and, if necessary,
adjust it as follows.
To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10680
s s
WARNING
After adjusting the drive chain
slack or removing and installing
the rear wheel, always check
the brake pedal free play.
If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this
adjustment.
After adjusting the brake pedal
free play, check the operation
of the brake light.
EAU22270
Adjusting the rear brake light
switch
1. Brake light swicht
2. Adjusting nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
1
1
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 48

Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22340
Checking the front and rear
brake pads
1. Wear limit indicator
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart. To check the
brake pad wear, measure the lining
thickness. If the lining thickness is
less than 0,8 mm (0,03 in), have a
Yamaha dealer replace the brake
pads as a set.
EWA10250
s s
WARNING
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
1. Wear indicator
EAU22580
Checking the brake fluid level
1. Minimum level mark
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the
brake fluid reservoir is level.
1. Minimum level mark

Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
FRONTREAR
FRONTREAR
11
11
1D0-F8199-E2.qxd 20/9/04 11:32 Página 49

This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, replace it as follows.
1. Remove cowling A. (See page
6-5.)
2. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.
3. Remove the headlight bulb hol-
der according to the following
illustration, and then remove the
defective bulb.
NOTE:
The removal procedure depends on
the type of bulb holder installed on
your vehicle.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Place a new bulb into position,
and then secure it with the bulb
holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
5. Install the bulb cover, and then
connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb
1. Screw (x2)
2. Lens
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
21
1D0-F8199-E2.qxd 20/9/04 11:32 Página 56