2005 YAMAHA BANSHEE 350 oil

8-9
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally
check the brake fluid level and add the fluid as required.
9On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two
years.
9Replace the brake hoses every four years, or if cracked or damaged.
5FK-9-66-05 12/3/04 7:54 PM Page 10

8-11
* L’entretien de ces élémets ne pouvaut être mené à bien sans les données techniques, les connaissances et l’outillage adéquats, il doit
être confié à un concessionnaire Yamaha.
INITIAL TOUS LES
mois 1 3 6 6 12
DÉSCRIPTION VÉRIFICATION km 320 1200 2400 2400 4800
(mi) (200) (750) (1500) (1500) (3000)
heures 20 75 150 150 300
*Fonctionnement de 9Contrôler le fonctionnement / fuites de liquite.
22222frein avant et arriére9Corriger si nécessaire.
*Plaquettes de frein
9Contrôler l’usure de plaquette.avant et arrière9Changer si nécessaire.222
*Embrayage
9Examiner le jeu et le fonctionnement.
2
2229Changer si nécessaire.
9Contrôler la flèche et l’alignement de la chaîne.
Chaîne de 9Régrer si nécessaire.
transmission9Nettoyer et graisser.2 2229Changer si nécessaire.
*Guide-chaîne et
rouleau
9Contrôler l’usure et changer si nécessaire.222
*Système de direction
9Examiner le jeu, nettoyer et lubrifier.22222
*Suspension avant et
arrière
9Examiner et lubrifier de la graisse à base de savon au lithium.22222
Pneus
9Examiner la pression d’air, le voile de roue, et
22222
l’usure de pneu.
*Roues
9Examiner les roulements.
222229Changer les roulements si nécessaire.
*Câble d’accélération
9Contrôler le cheminement et le connexion.
et de commande9Lubrifier.22222
Ecrous et boulons
extérieur
9Resserrer.22222
Cadre
9Nettoyer et examiner.2222
Equipement
d’éclairage
9Examiner.22222
Selon la
première
occurrence
5FK-9-66-05 12/3/04 7:54 PM Page 12

8-17
EBU10981
Transmission oil
Transmission oil measurement
1. Place the ATV on a level surface.
2. Warm up the engine for several minutes,
and then stop it.
3. Remove the oil filler cap and wipe off the
dipstick with a clean rag. Insert the dipstick
in the filler hole without screwing it in.
NOTE:
Wait a few minutes until the oil level settles
before checking.
4. Remove the dipstick and check the oil
level.
5. The oil level should be between the mini-
mum and maximum level marks. If the
level is low, add oil to raise it to the proper
level.
6. Install the oil filler cap.
q
w
e
1. Dipstick
2. Maximum level mark 3. Minimum level mark
1. Jauge
2. Repère de niveau maximum 3. Repère de niveau minimum
1. Varilla de nivel
2. Marca de máximo 3. Marca de mínimo
5FK-9-66-05 12/3/04 7:54 PM Page 18

8-19
Transmission oil replacement
1. Place the ATV on a level surface.
2. Warm up the engine for several minutes
and then stop it.
3. Place a container under the engine to col-
lect the used oil.
4. Remove the oil filler cap and drain bolt to
drain the oil.
5. Install the drain bolt, and then tighten it to
the specified torque.
6. Fill the engine with the recommended oil,
and then install the oil filler cap.
q
1. Drain bolt1. Boulon de vidange1. Perno de vaciado
Tightening torque:
Drain bolt:
20 Nm (2.0 m0kgf)
5FK-9-66-05 12/3/04 7:54 PM Page 20

8-21
cC
8In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING II” or higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil:
See page 10-2.
Oil quantity:
Periodic oil change:
1.5 L
5FK-9-66-05 12/3/04 7:54 PM Page 22

q
w
1. Maximum level mark
2. Minimum level mark
1. Repère maximum
2. Repère minimum
1. Marca de máximo
2. Marca de mínimo
8-23
7. Start the engine and warm up for a few
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the
engine immediately, and check for the
cause.
8. Turn the engine off, and then check the oil
level and correct it if necessary.
EBU01080
Cooling system
1. Check the coolant level in the coolant
reservoir when the engine is cold as the
coolant level will vary with engine temper-
ature. The coolant level should be
between the maximum and minimum
marks.
5FK-9-66-05 12/3/04 7:54 PM Page 24

8-47
6. Inspect the air filter element and replace it
if damaged.
7. Apply foam air filter oil to the air filter ele-
ment.
NOTE:
The air filter element should be wet but not drip-
ping.
8. Pull the air filter element over its frame,
and then install the lock plate by turning it.
9. Install the air filter element assembly.
10. Install the air filter case cover by hooking
the fasteners onto the air filter case.
11. Install the seat.
5FK-9-66-05 12/3/04 7:54 PM Page 48

8-77
8Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reac-
tion and lead to poor brake performance.
8Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock.
8Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
8Have a Yamaha dealer check the cause if the
brake fluid level goes down.
5FK-9-66-05 12/3/04 7:54 PM Page 78