2005 YAMAHA BANSHEE 350 clutch

6-11
EBU01981
Shifting
This model has a 6-speed forward transmission.
The transmission allows you to control the
amount of power you have available at a given
speed or for starting, accelerating, climbing hills,
etc. To shift into neutral, return the throttle lever
to its original position, apply the clutch and
repeatedly depress the shift pedal until it stops.
When it stops, it will be in first gear. Raise the
pedal slightly to neutral.
1 2 3 4 5 6N
N. NeutralN. Point mortN. Punto muerto
5FK-9-66-03 11/2/04 10:20 AM Page 12

6-13
cC
8Do not coast for long periods with the
engine off, and do not tow the machine a
long distance. Even in neutral position, the
transmission is only properly lubricated
when the engine is running. Inadequate
lubrication may cause damage.
8Always use the clutch when changing
gears. The engine, transmission and drive
train are not designed to withstand the
shock of forced shifting and can be dam-
aged by shifting without the clutch.
5FK-9-66-03 11/2/04 10:20 AM Page 14

6-15
EBU00204
To start out and accelerate
1. Release the throttle lever.
cC
Always close the throttle while shifting
gears. Otherwise, damage to the engine and
drive train may result.
2. Pull the clutch lever to disengage the clutch.
3. Shift into first gear.
4. Open the throttle gradually and at the same
time, release the clutch lever slowly.
5. Once the machine has attained adequate
speed, release the throttle, and at the same
time, quickly pull in the clutch lever.
6. Shift into second gear. (be careful not to
shift into neutral)
5FK-9-66-03 11/2/04 10:20 AM Page 16

6-17
7. Open the throttle part way and gradually
release the clutch lever.
8. Follow the same procedure when shifting to
the next higher gear.
w
Opening the throttle abruptly or releasing the
clutch lever too quickly would increase the
chance of an accident or could make the
machine wheelie including overturn. Always
open the throttle gradually and release the
clutch lever gradually.
5FK-9-66-03 11/2/04 10:20 AM Page 18

6-27
EBU11750
Parking on a slope
w
Avoid parking on hills or other inclines.
Parking on a hill or other incline could cause
the ATV to roll out of control, increasing the
chance of an accident. If you must park on
an incline, put the ATV in low gear, apply the
parking brake, and block the front and rear
wheels with rocks or other objects.
Do not park the ATV at all on hills that are so
steep you could not walk up them easily.
1. Bring the machine to a stop by applying the
brakes in low gear.
2. Stop the engine and release the clutch
lever.
3. With the rear brake applied, apply the park-
ing brake and slowly release the brake
pedal.
5FK-9-66-03 11/2/04 10:20 AM Page 28

7-37
With the engine idling, pull the clutch lever to dis-
engage the clutch and shift into 1st gear, and
then release the parking brake. Open the throttle
gradually, and at the same time, release the
clutch lever slowly. Once the ATV has attained
adequate speed, release the throttle lever and at
the same time, quickly pull in the clutch lever and
shift into 2nd gear. Open the throttle part way and
gradually release the clutch. Use this same pro-
cedure as you move into the higher gears. Be
sure to coordinate the use of the throttle and shift
pedal properly. If the throttle is applied too
abruptly or if the throttle is not released during
shifting, or if the shift pedal is not released before
applying the throttle, the front wheels may lift off
the ground resulting in a loss of directional con-
trol. Avoid higher speeds until you are thoroughly
familiar with the operation of your ATV.
w
Always open the throttle gradually and
release the clutch lever slowly. Otherwise,
the ATV could wheelie which would increase
the chance of an accident.
5FK-9-66-04 4/3/04 1:24 PM Page 38

8-8 * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.INITIAL EVERY
month 1 3 6 6 12
ITEM ROUTINEWhichever
km 320 1200 2400 2400 4800 comes first
(mi) (200) (750) (1500) (1500) (3000)
hours 20 75 150 150 300
* Front and rear9Check operation/fluid leakage.
22222
brake operation9Correct if necessary.
* Front and rear9Check pad wear.
222
brake pads9Replace if necessary.
* Clutch9Inspect free play and operation.
2222
9Replace if necessary.
9Check chain slack/alignment.
Drive chain9Adjust if necessary.
2222
9Clean and lube.
9Replace if necessary.
* Drive chain guard
9Check wear and replace if necessary.222
and rollers
* Steering system9Inspect free play, clean and lubricate.22222
* Front and rear
9Inspect and lubricate with lithium-soap-based grease.22222
suspension
Tires9Inspect air pressure, wheel runout, and tire wear.22222
* Wheels9Inspect bearings.
22222
9Replace bearings if necessary.
* Throttle, control cable9Check routing and connection.
22222
9Lubricate.
Outside nuts and bolts9Retighten.22222
Frame9Clean and inspect.2222
Lighting equipment9Inspect.22222
5FK-9-66-05 12/3/04 7:54 PM Page 9

8-21
cC
8In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING II” or higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil:
See page 10-2.
Oil quantity:
Periodic oil change:
1.5 L
5FK-9-66-05 12/3/04 7:54 PM Page 22