2005 TOYOTA xA tow

INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide
completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RM and
D
ISARM at the same time you remotely lock and unlock the doors. The system provides compre -
hensive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGERED and sound an ALARM when a door
is forcibly unlocked or opened*, or when a window is tapped on or broken. During the A
LARM, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash. A l s o , the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS MONITOR for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) and the G
LASS
B
REAKAGE SENSOR’S microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUS MONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the key in the
ignition switch to the “ON” or “START” position, and unlock them when you turn the key back to the
“ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer to page
18 for programming information.
* When the system is P
ASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an A
LARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS(PRE-ARMING)THEN STARTS FLASHING(SYSTEM IS ARMED)
Page 2 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 19
SCION
SECURITY
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail -
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
123123123
123123
123
123

PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.

Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123

OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.

The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.

Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.

4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123

OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.

The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.

Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.

4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123

PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.

Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123

INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide
completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RM and
D
ISARM at the same time you remotely lock and unlock the doors. The system provides compre -
hensive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGERED and sound an ALARM when a door
is forcibly unlocked or opened*, or when a window is tapped on or broken. During the A
LARM, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash. A l s o , the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS MONITOR for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) and the G
LASS
B
REAKAGE SENSOR’S microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUS MONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the key in the
ignition switch to the “ON” or “START” position, and unlock them when you turn the key back to the
“ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer to page
18 for programming information.
* When the system is P
ASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an A
LARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS(PRE-ARMING)THEN STARTS FLASHING(SYSTEM IS ARMED)
Page 2 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 19
SCION
SECURITY
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail -
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
123123123
123123
123
123