2005 TOYOTA TACOMA clock

52005 TACOMA from Mar. ’05 Prod. (OM35862U)
1. Front fog light switch
2. Rear differential lock switch or “AUTOLSD” switch
3. Power outlet main switch
4. Instrument panel light control dial
5. Headlight and turn signal switches
6. Audio remote control switches
7. Wiper and washer switches
8. Front drive control switch knob
9. Audio system
10. Clock
11. Engine immobilizer system indicator light
12. Front passenger ’s seat belt reminder light
13. Front passenger occupant classification indicator lights or passenger airbag on −
off indicator lights
14. Passenger airbag manual on −off switch
15. Air conditioning controls
16. Power outlet
17. Emergency flasher switch
18. Cigarette lighter
19. Parking brake lever (manual transmission)
LS11004a

312005 TACOMA from Mar. ’05 Prod. (OM35862U)
Do not fill a fuel container in the
bed under any circumstances. A
static electricity charge could cause
a spark and fire hazard. The proper
procedure is to place an approved
fuel container on the ground away
from the truck for filling.
LS12038b
2. To remove the fuel tank cap, turnthe cap counterclockwise by 90 de-
grees (to the pressure point 1), and
then turn it an additional 30 degrees
(to point 2). Pause slightly before
removing it.
It is not unusual to hear a slight swoosh
when the cap is opened.
When installing the cap, turn the cap
clockwise until you hear a click. When
you hear the click, the cap is fully
closed.
If the cap is not tightened securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely. The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.
CAUTION
Make sure the cap is installed se-
curely to prevent fuel sp
illage in
the event of an accident.
Use only a genuine Toyota fuel tank
cap for replacement. It is designed
to regulate fuel tank pressure.
NOTICE
To prevent damage to the cap, apply
force only in the turning direction to
the cap. Do not pull or pry it.

562005 TACOMA from Mar. ’05 Prod. (OM35862U)
Improperly seated and/or restrained
infants and children can be killed
or seriously injured by the
deploying airbags. An infant or
child who is too small to use a seat
belt should be properly secured
using a child restraint system. As
to access cab models, Toyota
strongly recommends that all
infants and children be placed in
the rear seat of the vehicle and
properly restrained. The rear seat is
the safest for infants and children.
For instructions concerning the
installation of a child restraint
system, see “Child restraint” on
page 86 in this Section.
LS13142a
Indicator light
Bench seat
LS13141a
Indicator light
Separate seats
The passenger airbag system is
equipped with a manual onoff switch
and indicator light. Turning the passen-
ger airbag manual onoff switch clock-
wise to the “ON” or “AUTO” position
makes the front passenger airbag sys-
tem operational. To disable the front
passenger airbag system, turn the
manual onoff switch counterclockwise
to the “OFF” position and remove the
key. The “OFF” indicator light on the
passenger airbag manual onoff switch
will come on when the front passenger
airbag system has been disabled.
See “Passenger airbag manual on −off
switch” on page 71 in this Section for
detail.

712005 TACOMA from Mar. ’05 Prod. (OM35862U)
NOTICE
Do not disconnect the battery cables
before contacting your Toyota dealer.
LS13142a
Indicator light
Bench seat
LS13141a
Indicator light
Separate seats
This onoff switch is designed to dis-
able the front passenger airbag in order
to allow usage, if necessary, of a mem-
ber of a passenger risk group identified
in TABLE 1 is occupying the right front
passenger seating position. (For details,
see “SRS driver airbag and front pas-
senger airbag” on page 55 in this Sec-
tion.)
Operate onoff switch as follows:
Insert key into the keyhole.
To turn the front passenger airbag on—
Vehicles with bench seat:
Turn the key clockwise to the “ON” posi-
tion. At this time, the “ON” indicator light
comes on.
Vehicles with separate seats:
Turn the key clockwise to the “AUTO”
position. At this time, the indicator light
condition varies depending on the occu-
pant in the right front seat. (For details,
see “Front passenger occupant classifica-
tion system” on page 80 in this Section.)
To turn the front passenger airbag
off—Turn the key counterclockwise to the
“OFF” position and remove it. At this time,
the “OFF” indicator light comes on. If the
key is removed at any other position than
“OFF”, the switch will automatically return
to the “ON” or “AUTO” position.
Passenger airbag manual onoff
switch (regular cab and access cab
models only)

912005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13027a
Bench seat
LS13006a
Separate seats
When you install a rearfacing child re-
straint system which belongs to a pas-
senger risk group on the right front
seat, turn the passenger airbag manual
onoff switch counterclockwise to the
“OFF” position and remove the key.
(For details, see “SRS driver airbag and
front passenger airbag” on page 55 in
this Section.)
The indicator light comes on when the
system is off.
CAUTION
If you must install a rearfacing child
restraint system on the right front
seat, make sure that the front passen-
ger airbag manual onoff switch is in
the “OFF” position with the key re-
moved and that the indicator light is
on.
LS13007
CAUTION
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.
If the driver ’s seat position does
not allow sufficient space for safe
installation, install the child re-
straint system on the rear right
seat.

952005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13027a
Bench seat
LS13006a
Separate seats
When you install a rearfacing child re-
straint system which belongs to a pas-
senger risk group on the right front
seat, turn the passenger airbag manual
onoff switch counterclockwise to the
“OFF” position and remove the key.
(For details, see “SRS driver airbag and
front passenger airbag” on page 55 in
this Section.)
The indicator light comes on when the
system is off.
CAUTION
If you must install a rearfacing child
restraint system on the right front
seat, make sure that the passenger
airbag manual onoff switch is in the
“OFF” position with the key removed
and that the indicator light is on.
CAUTION
Forwardfacing child restraint system:
A forwardfacing child restraint
system which belongs to a passenger
risk group should never be installed
on the right front passenger seat with
the passenger airbag manual onoff
switch in the “ON” or “AUTO”
position, because the force of the
deploying airbag could cause death
or serious injury to the child in
forward seating position. (For details,
see “SRS driver airbag and front
passenger airbag” on page 55 in this
Section.)

1702005 TACOMA from Mar. ’05 Prod. (OM35862U)
The A.D.D. can be engaged or disen-
gaged by the shifting operations de-
scribed in “(c) Shifting procedure”.
You should drive in four−wheel drive for
at least 16 km (10 miles) each month.
This will assure that the front drive com-
ponents are lubricated. SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”,
reduce the
vehicle speed to less than 100 km/h (62
mph) and turn the front drive control
switch knob fully clockwise.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H2” to
the “H4” position, this reminds you that
the transfer mode is not securely in “H4”
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four −wheel drive indicator light con-
tinues to blink and the buzzer sounds
when you operate the front drive control
switch knob from the “H2” to the “H4”
position, this reminds you that the transfer
mode is not in “H4” mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Operate the
switch knob again.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
To shift from “H4” to “H2”, turn the
front drive control switch knob fully coun-
terclockwise.
This can be done at any speed. You need
not depress the clutch pedal.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H4” to
the “H2” position, this reminds you that
the transfer mode is not securely in “H2”
mode. Drive straight ahead while acceler-
ating or decelerating, or drive forward or
backward in a short distance.
If the indicator light continues to blink
even if doing so, contact your Toyota
dealer as soon as possible. There may be
a trouble in the four −wheel drive system.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
(b) A.D.D. (automatic
disconnecting differential) (c) Shifting procedure (with
manual transmission)

1712005 TACOMA from Mar. ’05 Prod. (OM35862U)
SHIFTING BETWEEN “H4” AND “L4”
To shift from “H4” to “L4”, stop the
vehicle or reduce the vehicle speed to
less than 3 km/h (2 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and push and turn the front
drive control switch knob fully clockwise.
To shift from “L4” to “H4”, stop the
vehicle or reduce the vehicle speed to
less than 3 km/h (2 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and turn the front drive con-
trol switch knob fully counterclockwise.
If the “4LO” (low speed four −wheel drive)
indicator light continues to blink when you
operate the front drive control switch knob
to the “H4” or “L4” position, drive forward
or backward in a short distance, then stop
the vehicle completely, depress the clutch
pedal and operate the switch knob again.
If the indicator continues to blink even if
doing so, contact your Toyota dealer as
soon as possible. There may be a trouble
in the four −wheel drive system.CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”, reduce the
vehicle speed to less than 100 km/h (62
mph) and turn the front drive control
switch knob fully clockwise.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H2” to
the “H4” position, this reminds you that
the transfer mode is not securely in “H4”
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four −wheel drive indicator light con-
tinues to blink and the buzzer sounds
when you operate the front drive control
switch knob from the “H2” to the “H4”
position, this reminds you that the transfer
mode is not in “H4” mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Operate the
switch knob again.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
(c) Shifting procedure (with
automatic transmission)