2005 TOYOTA TACOMA belt

11 42005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13071
Symbol mark
Routing
device
or
upper
anchor
bracket
Lower
anchor
bracket
Use the routing device and the anchor
bracket to attach the top strap.
Upper anchor bracket is installed for front
passenger ’s seating position, lower anchor
bracket is installed for right−rear seating
position.
This symbol indicates the locations of
user ready anchor bracket.
LS13072Symbol mark
TO USE THE ANCHOR BRACKET:
Front position—
1. Remove the passenger head re- straint.
Lightly push down on the top sur-
face of the anchor bracket cover
with the symbol mark shown in the
illustration, then pull it forward to
remove.
LS13073
2. Fix the child restraint system withthe seat belt.
Latch the hook onto the anchor
bracket on the back panel and tight-
en the top strap.
For instructions on installing the child re-
straint system, see “Child restraint” on
page 86 in this Section.

11 62005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13076a
Routing
device
2. Fix the child restraint system withthe seat belt.
Route the top strap through the
routing device as shown in the il-
lustration.
For instructions on installing the child re-
straint system, see “Child restraint” on
page 86 in this Section.
CAUTION
Make sure the top strap is not
twisted.
LS13077a
3. Latch the hook onto the rear lower anchor bracket and tighten the top
strap.
Store the removed covers in a safe place
such as the glove box.
Be sure to replace the covers when the
anchor bracket is not in use.
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instructions
provided by its manufacturer.
LS13051
Follow the procedure below for a child
restraint system that requires the use
of a top strap.
—U sin g a to p st rap
(double cab models)

11 82005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13068
3. Fix the child restraint system withthe seat belt and tighten the top
strap.
Replace the head restraint.
For instructions on installing the child re-
straint system, see “Child restraint” on
page 86 in this Section.
CAUTION
When returning the seatback to its
original position, make sure the
seatback is securely locked by
pushing forward and rearward on
the top of the seatback. Failure to
do so will prevent the seat belt
from operating properly.
Make sure the top strap is securely
latched, and check that the child
restraint system is secure by push-
ing and pulling it in different direc-
tions. Follow all the installation in-
structions provided by its manufac-
turer.
LS13078
Separate seats
LS13079
Bench seat
—Installation with child
restraint lower anchorages
(regular cab models)

11 92005 TACOMA from Mar. ’05 Prod. (OM35862U)
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the right passenger ’s seat-
ing position.
The anchorages are installed in the gap
between the seat cushion and seatback of
the right side of the seat as shown in the
illustration.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
LS13160a
1st lock
position
10th lock
position
CHILD RESTRAINT SYSTEM
INSTALLATION 1. Separate seats only—Fold down the seatback and back to the 1st lock
position (most upright position) until
it locks into place. Adjust the seat-
back to the 10th lock position.
Make sure the seatback is locked secure-
ly.LS13080
Canada only
Ty p e A

1202005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13081
Canada only
Ty p e B
2. Widen the gap between the seat cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.
3. Type A—Latch the hooks of lower straps onto the anchorages and
tighten the lower straps.
Type B—Latch the buckles onto the
anchorages.
For owners in Canada— The symbol on
a child restraint system indicates the pres-
ence of a lower connector system.
If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 110 in this Section.)
For installation details, refer to the instruc-
tion manual equipped with each product.CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never slide or recline the
seat.

1212005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13078
Front seat
LS13099
Rear seat
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the seat.
Front seat without seatback table—
The anchorages are installed in the gap
between the seat cushion and seatback of
the seat as shown in the illustration.
Front seat with seatback table—
The anchorages are installed in the seat
cushion of the seat.
Rear seat—
The anchorages are located at the base
of the seatback as shown in the illustra-
tion.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
LS13160a
1st lock
position
10th lock
position
CHILD RESTRAINT SYSTEM
INSTALLATION 1. Front seat—Fold down the front seat seatback and back to the 1st lock
position (most upright position) until
it locks into place. Adjust the seat-
back to the 10th lock position.
Make sure the seatback is locked secure-
ly.
—Installation with child
restraint lower anchorages
(access cab models)

1242005 TACOMA from Mar. ’05 Prod. (OM35862U)
Front seat—2. Front seat without seatback table— Widen the gap between the seat
cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.
Front seat with seatback table—Wid-
en the slits of the seat cushion
slightly and confirm the position of
the lower anchorages near the but-
ton on the seat cushion.
3. Type A—Latch the hooks of lower straps onto the anchorages and
tighten the lower straps.
Type B—Latch the buckles onto the
anchorages.
Rear seat—
Type A—Latch the hooks of lower
straps onto the anchorages and tighten
the lower straps.
Type B—Latch the buckles onto the an-
chorages.
For owners in Canada— The symbol on
a child restraint system indicates the pres-
ence of a lower connector system. If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 113 in this Section.)
For installation details, refer to the instruc-
tion manual equipped with each product.
CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never slide or recline the
seat.
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.

1252005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13084
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the rear seat.
The anchorages are installed in the gap
between the seat cushion and seatback of
both outside rear seats as shown in the
illustration.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed with these anchorages. In
this case, it is not necessary to fix the
child restraint system with a seat belt on
the vehicle.LS13085
Canada only
Ty p e A
LS13086
Canada only
Ty p e B
—Installation with child
restraint lower anchorages
(double cab models)