2005 SUZUKI MARUTI lock

Downloaded from www.Manualslib.com manuals search engine 10583K
Fuel Filter (Diesel engine)
(1) Fuel Filter
The fuel filter works as a water sedimentor
as well.
Drain water according to the Periodic
Maintenance Schedule. To drain water:
1) Place a pan or ample rag under the fuel
filter drain nozzle.
2) Loosen the drain knob. The water will be
drained.
3) Tighten the drain knob when the water
changes to the diesel fuel.
4) Tighten the drain knob.
NOTE:
Trust this job to be carried out at Maruti
Suzuki authorized dealer.
83K-07-030
Front Fog Light (if equipped)1) Insert a flat blade screwdriver into the
hole (2) and remove the clips (1) by
twist the driver as shown in the illustra-
tion.
83K-07-029D
83K-07-029E
2) Open the fender cover. Disconnect the
coupler with pushing the lock release.
Turn the bulb holder counterclockwise
and remove it.
INSPECTION AND MAINTENANCE
9-16

Downloaded from www.Manualslib.com manuals search engine 10783K
INSPECTION AND MAINTENANCE
9-18
With the engine running, measure the dis-
tance between the brake pedal and floor
carpet when the pedal is depressed with
approximately 30 kg (66 lbs) of force. The
minimum distance required is as specified.
Since your vehicle’s brake system is self-
adjusting, there is no need for pedal
adjustment.
If the pedal to floor wall distance as mea-
sured above is less than the minimum dis-
tance required, have your vehicle inspec-ted
by your MARUTI SUZUKI dealer.NOTE:
When measuring the distance between the
brake pedal and floor wall, be sure not to
include the floor mat or rubber on the floor
wall in your measurement.
83K-07-033
Parking Brake
Ratchet tooth specification “b”:
4th – 9th
Lever pull force (1):
200 N (20 kg, 44 lbs)
w ww w
w WARNING
If you experience any of the following
problems with your vehicle’s brake
system, have the vehicle inspected
immediately by your MARUTI SUZUKI
dealer.
Poor braking performance
Uneven braking (Brakes not working
uniformly on all wheels.)
Excessive pedal travel
Brake dragging
Excessive noise
83K-07-034
EXAMPLE
Check the parking brake for proper adjust-
ment by counting the number of clicks made
by the ratchet teeth as you slowly pull up
on the parking brake lever to the point of
full engagement. The parking brake lever
should stop between the specified ratchet
teeth and the rear wheels should be
securely locked. If the parking brake is not
properly adjusted or the brakes drag after
the lever has been fully released, have the
parking brake inspected and/or adjusted by
your MARUTI SUZUKI dealer.Steering
EXAMPLE
Steering wheel play “c”:
0 – 30 mm (0.0 – 1.2 in.)
Check the play of the steering wheel by
gently turning it from left to right and mea-
suring the distance that it moves before you
feel slight resistance. The play should be
between the specified values.
Check that the steering wheel turns easily
and smoothly without rattling by turning it
all the way to the right and to the left while
83K-07-035

Downloaded from www.Manualslib.com manuals search engine 11183K
INSPECTION AND MAINTENANCE
9-22
83K-07-043
83K-07-044
Fuses in the Engine Compartment(For Petrol Engine Model)
Replacement of the battery
83K-07-42A
EXAMPLETo remove the battery:
1) Disconnect the negative cable (1).
2) Disconnect the positive cable (2).
3) Remove the retainer bolts (3) and
remove the retainer (4).
4) Remove the battery along with cover
assembly (5) (if equipped).
To install the battery:
1) Install the battery in the reverse order
of removal.
2) Tighten the retainer bolt and battery
cables securely.NOTE:
When the battery is disconnected, some of
the vehicle’s function will be initialized and/
or deactivated.
These function are required to reset after
the battery is reconnected.
FusesYour vehicle has three types of fuses, as
described below:
Main fuse
The main fuse takes current directly from
the battery.
Primary fuses
These fuses are between the main fuse and
individual fuses, and are for electrical load
groups.
Individual fuses
These fuses are for individual electrical cir-
cuits.
(1) 80A All electric load
(2) 50A Power window, Ignition,
Wiper, Starter
(3) 50A Tail light, Rear defogger,
Door lock, Hazard/Horn,
Dome
(4) – Radiator fan relay #1
(5) – Radiator fan relay #2
(6) – Radiator fan relay #3
(7) – Starting motor relay
(8) – Main relay
(9) – Blank
(10) – Front fog light relay
(11) – Fuel pump relayMAIN FUSE/PRIMARY FUSE(For Petrol Engine Model)

Downloaded from www.Manualslib.com manuals search engine 11483K
INSPECTION AND MAINTENANCE
9-25(1) – Blank
(2) 15A Ignition coil
(3) 10A Back-up light
(4) 10A Meter
(5) 15A Accessory 1
(6) 15A Accessory 2
(7) 30A Power window
(8) 15A Wiper / Washer
(9) 10A IG1 SIG
(10) 15A Air bag
(11) 10A Anti-lock brake system
(12) 10ATail light
(13) – Blank
(14) 20A Door lock
(15) – Blank
(16) 10A ST SIG
(17) 10A Immobilizer
(18) 10A IG2 SIG
(19) 15A Rear fog light
(20) 15ARadio
(21) 20A Rear defogger
(22) 15A Horn / Hazard
(23) – Blank
(24) – BlankMAIN FUSE/PRIMARY FUSE
83K-07-051
The fuse box is located under the driver’s
side of the dashboard.
Remove the fuse box cover by pushing in
at both ends and pulling off the cover.
To remove a fuse, use the fuse puller pro-
vided in the fuse box.
83K-07-052
w ww w
w WARNING
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
V VV V
V
w ww w
w WARNING
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI authorized dealer.V VV V
V
Bulb Replacement Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially for
halogen headlight bulbs. Replace the
bulbs after they become cool
enough.
The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
w ww w
w WARNING
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
CAUTION

Downloaded from www.Manualslib.com manuals search engine 11683K
INSPECTION AND MAINTENANCE
9-27 Other General LightsBulb holder
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
pull it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
(3) Removal
(4) Installation
There are two types of bulb, “Full glass
type” (1) and “Glass/metal type” (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.Front Parking light (1)
Front turn signal light (2)
Rear combination light
83K-07-058
83K-07-059
83K-07-06083K-07-061
EXAMPLEEXAMPLEBulb can be replaced after taking out the
side turm lamp.

Downloaded from www.Manualslib.com manuals search engine 11883K
INSPECTION AND MAINTENANCE
9-29
CAUTION
To avoid scratching or breaking of the
window, do not let the wiper arm
strike the window while replacing the
wiper blade.
For windshield wipers:NOTE:
Some wiper blades may be different from
the ones described here depending on
vehicle specifications. If so, consult your
MARUTI SUZUKI dealer for proper
replacement method.1) Hold the wiper arm away from the win-
dow.
83K-07-068
To install new wiper blades, follow the pro-
cedures below.
2) Squeeze lock (1) towards wiper arm (2)
and remove the wiper frame from the
arm as shown.
3) Unlock the lock end of the wiper blade
and slide the blade out as shown.
83K-07-069
83K-07-07083K-07-071
EXAMPLE
EXAMPLE
Removal
Installation
(1) Locked end

Downloaded from www.Manualslib.com manuals search engine 11983K
INSPECTION AND MAINTENANCE
9-30
For rear wipers (if equipped)
1) Hold the wiper arm away from the win-
dow.
2) Remove the wiper frame from the arm
as shown.
3) Slide the blade out as shown.
NOTE:
Do not flex the wiper blade frame end more
than necessary. If you do, it can break off.
83K-07-073
83K-07-074
4) If the new blade is provided without the
two metal retainers (1) move them from
the old blade to the new one.
5) Install the new blade in the reverse order
of removal. with the locked end
positioned toward the wiper arm.
Make sure the blade is properly retained
by all the hooks. Lock the blade end into
place.
6) Reinstall wiper frame to arm, making
sure that the lock lever is snapped
securely in the arm.
Windshield Washer Fluid(Front and rear)
83K-07-076
EXAMPLE
83K-07-072
(1) Retainer

Downloaded from www.Manualslib.com manuals search engine 12283K
Tyre Changing ToolSpare tyre and tyre changing tool
The jack, wheel brace, jack handle (and
towing hook) are stowed just under the
spare tyre in the luggage compartment.To remove the spare tyre, turn its nut (1)
counterclockwise and remove it.the storage bracket and turn the shaft
clockwise until the jack is securely held in
place.
83K-08-00183K-08-002
83K-08-00383K-08-004
w ww w
w WARNING
The jack should be used only to
change wheels. It is important to read
the jacking instructions in this section
before attempting to use the jack.
w ww w
w WARNING
After using the tyre changing tools, be
sure to stow them securely or they
can cause injury if an accident occurs.
EMERGENCY SERVICE
10-1
To remove the jack, turn its shaft counter-
clockwise and pull the jack out of the stor-
age bracket. To stow the jack, place it in
Jacking Instructions1) Place the vehicle on level, hard ground.
83K-08-005
EXAMPLE