2005 SUZUKI GRAND VITARA warning

YH4
GRAND
VITARA
14
15
1. Driver air bag (inflator) module
2. Steering wheel
3. Steering wheel nut
4. Contact coil and combination switch assembly
5. Steering column upper cover
6. Steering column lower cover
7. Steering column assembly
8. Steering lock assembly
9. Steering column hole cover
10. Steering shaft joint
11. Steering lower shaft assembly
12. Adjustable steering column release lever
(if equipped)
13. Steering column lower seal
14. With adjustable steering column release lever type
15. Without adjustable steering column release lever type
3C1-2 AIR BAG STEERING WHEEL AND COLUMN
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified screws, bolts, and nuts be used as
designated and that they are tightened to the specified torque. When the column assembly is removed from the
vehicle, special care must be taken in handling it. Use of a steering wheel puller other than the one recommended
in this manual or a sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly
could shear the plastic shear pins which maintain column length and position.
The driver air bag (inflator) module is one of the supplemental restraint (air bag) system components and is
mounted to the center of the steering wheel. During certain frontal crashes, the air bag system supplements the
restraint of the driver's and passenger's seat belts by deploying the air bags. The air bag (inflator) module should
be handled with care to prevent accidental deployment. When servicing, be sure to observe all WARNINGS in this
section. Refer to ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
1 11
1. Mounting bolt
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
3C1-4 AIR BAG STEERING WHEEL AND COLUMN
DRIVE AIR BAG (INFLATOR) MODULE
WARNING:
When handling an air bag (inflator) module, be sure to read
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SERVICEº
in Section 10B and observe each instruction. Failure to fol-
low them could cause a damage to the air bag (inflator) mod-
ule or result in personal injury.
REMOVAL
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Loosen 2 bolts mounting driver air bag (inflator) module till it
turns freely, pull them out and fix them to bolt clamps.
4) Remove air bag (inflator) module from steering wheel.
5) Remove driver air bag (inflator) module (yellow) connector and
horn connector from steering wheel.
6) Disconnect driver air bag (inflator) module (yellow) connector of
driver air bag (inflator) module and horn connector as shown in
the figure.
ii) Release locking of lever.
ii) After unlocked, disconnect connector.
WARNING:
Special care is necessary when handling and storing a
live (undeployed) air bag (inflator) module. Observe
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SER-
VICEº in Section 10B. Otherwise, personal injury may re-
sult.

YH4
GRAND
VITARA
6, (a)
1. Trim cover (pad surface)
2. Inflator case
3. Wire harness
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
5. Mounting bolt (left side)
6. Mounting bolt (right side)
AIR BAG STEERING WHEEL AND COLUMN 3C1-5
INSPECTION
WARNING:
Never disassemble air bag (inflator) module or measure its
resistance. Otherwise, personal injury may result.
CAUTION:
If air bag (inflator) module was dropped from a height of
90 cm (3 ft) or more, it should be replaced.
Check air bag (inflator) module visually and if any of the following
is found, replace it with a new one.

Air bag being deployed.

Trim cover (pad surface) being cracked.

Wire harness or connector being damaged.

Air bag (inflator) module being damaged or having been exposed
to strong impact (dropped).
INSTALLATION
1) Connect horn connector securely.
2) Connect yellow connector of driver air bag (inflator) module con-
nector as shown in the figure securely.
ii) Connect connector.
ii) Lock connector with lock lever.
3) Install horn connector and driver air bag (inflator) module con-
nector.
4) Install driver air bag (inflator) module to steering wheel, taking
care so that no part of wire harness is caught between them.
5) Make sure that clearance between module and steering wheel
is uniform all the way.
6) Tighten driver air bag (inflator) module mounting bolt (left side)
to specified torque first and then driver air bag (inflator) module
mounting bolt (right side) to specified torque.
Tightening Torque
(a): 9 N
.m (0.9 kg-m, 6.5 lb-ft)
7) Connect negative battery cable.
8) Enable air bag system. Refer to ªENABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
1
3C1-10 AIR BAG STEERING WHEEL AND COLUMN
REMOVAL
WARNING:
Never rest a steering column assembly on the steering
wheel with air bag (inflator) module face down and column
vertical. Otherwise personal injury may result.
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Remove steering wheel and contact coil and combination switch
assembly, if necessary. Refer to ªSTEERING WHEELº and
ªCONTACT COIL AND COMBINATION SWITCH ASSEMBLYº
in this section.
Perform the following procedure if not removing steering wheel
and/or combination switch.
ii) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
4) Remove steering column hole cover.
5) Disconnect all connectors for the following parts.

Contact coil and combination switch

Ignition switch
6) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
7) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
ªAº: Drill hole with approximately
3 mm (0.12 in.) diameter.
REAR SUSPENSION 3E-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to SECTION 3.
SHOCK ABSORBER CHECK

Inspect for deformation or damage.

Inspect bushings for wear or damage.

Inspect for evidence of oil leakage.
Replace any defective part.
WARNING:
When handling rear shock absorber in which high-pressure
gas is sealed, make sure to observe the following precau-
tions.
1) Don't disassemble it.
2) Don't put it into the fire.
3) Don't store it where it gets hot.
4) Before disposing it, be sure to drill a hole in it where
shown by an arrow in the figure and let gas and oil out.
Lay it down sideways for this work.
5) The gas itself is harmless but it may issue out of the hole
together with chips generated by the drill. Therefore, be
sure to wear goggle.
LOWER ROD, UPPER ROD, LATERAL ROD
CHECK
Inspect for cracks, deformation or damage.
Replace any defective part.
Inspect each bush for wear and breakage. If found defective, re-
place.
AXLE HOUSING AND COIL SPRING CHECK
Inspect for cracks, deformation or damage.
Inspect for evidence of oil leakage at axle housing.
If any, replace defective part.

YH4
GRAND
VITARA
[A]: Before correction
[B]: Corrective weights
1. Heavy spot wheel tramp
2. Balance weights addition point
3. C / L of spindle
[C]: Before correction
[D]: Corrective weights
1. Heavy spot wheel shimmy
2. Balance weights addition point
3. C / L of spindle
WHEELS AND TIRES 3F-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to SECTION 3.
BALANCING WHEELS
There are two types of wheel and tire balance: static and dynamic.
Static balance, as shown in left figure, is equal distribution of weight
around wheel. Wheels that are statically unbalanced cause bounc-
ing action called tramp. This condition will eventually cause uneven
tire wear.
Dynamic balance, as shown in left figure, is equal distribution of
weight on each side of wheel centerline so that when the tire spins
there is no tendency for the assembly to move from side to side.
Wheels that are dynamically unbalanced may cause shimmy.
GENERAL BALANCE PROCEDURE
Deposits of mud, etc. must be cleaned from inside of rim.
WARNING:
Stones should be removed from tread in order to avoid operator injury during spin balancing and to
obtain good balance.
Tire should be inspected for any damage, then balanced according to equipment manufacturer's recommendation.
OFF-VEHICLE BALANCING
Most electronic off-vehicle balancers are more accurate than on-vehicle spin balancers. They are easy to use and
give a dynamic (two plane) balance. Although they do not correct for drum or disc unbalance as does on-vehicle
spin balancing, this is overcome by their accuracy, usually to within 1 / 8 ounce.
ON-VEHICLE BALANCING
ON-vehicle balancing methods vary with equipment and tool manufacturers. Be sure to follow each manufacturer's
instructions during balancing operation.

YH4
GRAND
VITARA
WHEELS AND TIRES 3F-7
TIRE
MOUNTING AND DEMOUNTING
Use tire changing machine to mount or demount tires. Follow equip-
ment manufacturer's instructions. Do not use hand tools or tire
irons alone to change tires as they may damage tire beads or wheel
rim.
Rim bead seats should be cleaned with wire brush or coarse steel
wool to remove lubricants, old rubber and light rust. Before mount-
ing or demounting tire, bead area should be well lubricated with ap-
proved tire lubricant.
After mounting, inflate to 240 kPa (35psi) so that beads are com-
pletely seated. Then adjust pressure to specified shown an tire
placard.
WARNING:
Do not stand over tire when inflating. Bead may break when
bead snaps over rim's safety hump and cause serious per-
sonal injury.
Do not exceed 240 kPa (35 psi) pressure when inflating. If
240 kPa (35 psi) pressure will not seat beads, deflate, re-lu-
bricate and reinflate. Over inflation may cause bead to break
and cause serious personal injury.
Install valve core and inflate to proper pressure.
TIRE REPAIR
There are many different materials and techniques on the market
to repair tires. As not all of these work on all types of tires, tire
manufacturers have published detailed instructions on how and
when to repair tires. These instructions can be obtained from the
tire manufacturer.

YH4
GRAND
VITARA
5
BRAKES 5-1
GENERAL DESCRIPTION5- 2 . . . . . . . . . . . . . .
DIAGNOSIS5- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Road Testing Brakes 5- 3. . . . . . . . . . . . . . . . . .
Brake Fluid Leaks 5- 3. . . . . . . . . . . . . . . . . . . .
Substandard or Contaminated
Brake Fluid 5- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 5- 4. . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5- 7 . . . . . . . . . . . .
Bleeding Brakes 5- 7. . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Free Height Check 5- 9. . . . . . . .
Brake Light Switch Adjustment 5- 9. . . . . . . . .
Excessive Pedal Travel Check 5- 9. . . . . . . . .
Brake Pedal Play Check 5-10. . . . . . . . . . . . . . .
Brake Fluid Level Check 5-10. . . . . . . . . . . . . . . Brake Hose and Pipe Check 5-10. . . . . . . . . . .
Master Cylinder Check 5-10. . . . . . . . . . . . . . . .
Brake Disc Check 5-11. . . . . . . . . . . . . . . . . . . .
Brake Pad Check 5-11. . . . . . . . . . . . . . . . . . . . .
Brake Shoe Check 5-11. . . . . . . . . . . . . . . . . . . .
Parking Brake Check and
Adjustment 5-12. . . . . . . . . . . . . . . . . . . . . . . . .
Flushing Brake Hydraulic System 5-13. . . . . . .
Fluid Pressure Test 5-13. . . . . . . . . . . . . . . . . . .
Booster Operation Check 5-15. . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5-17 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL5-17 . . . . . . . .
SPECIAL TOOLS5-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
BRAKES
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

When inspecting and servicing vehicle equipped with ABS, be sure to refer to section 5E or 5E1 first.

All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to as-
sure proper retention of all parts. There is to be no welding as it may result in extensive damage and
weakening of the metal.
DIAGNOSIS5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKE PIPE / HOSE / MASTER CYLINDER5A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT BRAKE5B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING AND REAR BRAKE5C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS