2005 SUZUKI GRAND VITARA Starting system

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-9
Fig. 1 for Step 1 Fig. 2 for Step 1 Fig. 3 for Step 2
1. Monitor coupler
2. Service wire
A: Diagnosis switch terminal
B: Ground terminal
Fig. 4 for Step 3
ªCHECK ENGINEº light
0.5
ON
OFF
TIME (sec.)
DIAGNOSTIC FLOW TABLE

STEPACTIONYESNO
11) Make sure that diagnosis switch
terminal in monitor coupler is not
grounded by service wire. See Fig. 1.
2) Check malfunction indicator lamp
while ignition switch is ON (but without
starting engine). See Fig. 2.
Dose malfunction indicator lamp flash?Go to Step 3.
If malfunction indicator lamp
remains ON, go to Step 2.

If malfunction indicator lamp
remains OFF, go to
ªMALFUNCTION INDICATOR
LAMP CHECKº in Section 6.
21) Using service wire, ground diagnosis
switch terminal in monitor coupler.
See Fig. 3.
Dose malfunction indicator lamp flash?Immobilizer control
system is in good
condition.Go to ªMALFUNCTION
INDICATOR LAMP CHECKº in
Section 6.
3Dose malfunction indicator lamp flash as
Fig. 4?Go to Step 4.Go to ªMALFUNCTION
INDICATOR LAMP CHECKº in
Section 6.
41) Check DTC stored in immobilizer
control module referring to
ªDIAGNOSTIC TROUBLE CODE
CHECK (IMMOBILIZER CONTROL
MODULE)º in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Go to Step 5.
51) Check DTC stored in ECM/PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s)?Go to flow table for
DTC No.Substitute a known-good ECM/
PCM and recheck.
NOTE:
After replacing with a known-
good ECM/PCM, register
ECM / Immobilizer Control
Module code in ECM/PCM by
performing procedure described
in ªProcedure after ECM/PCM
Replacementº section.

YH4
GRAND
VITARA
8G-10 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
DIAGNOSTIC FLOW TABLE

STEPACTIONYESNO
11) Check immobilizer indicator lamp
while ignition switch is ON (but without
starting engine). See Fig. 1.
Dose immobilizer indicator lamp flash?Go to Step 3.
If immobilizer indicator lamp
remains ON, go to Step 2.

If immobilizer indicator lamp
remains OFF, go to
ªIMMOBILIZER INDICATOR
LAMP CHECKº in this section.
21) Check DTC stored in ECM / PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s)?Go to ªIMMOBILIZER
INDICATOR LAMP
CHECKº in this section.Immobilizer control system is in
good condition.
31) Check DTC stored in immobilizer
control module referring to
ªDIAGNOSTIC TROUBLE CODE
CHECK (IMMOBILIZER CONTROL
MODULE)º in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Go to Step 4.
41) Check DTC stored in ECM / PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s) for immobilizer
control system?Go to flow table for
DTC No.Substitute a known-good ECM /
PCM and recheck.
NOTE:
After replacing with a known-
good ECM / PCM, register
ECM / Immobilizer Control
Module code in ECM / PCM by
performing procedure described
in ªProcedure after ECM / PCM
Replacementº section.
FIg. 1 for Step 1

YH4
GRAND
VITARA
8G-26 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
ON-VEHICLE SERVICE
PRECAUTIONS IN HANDLING IMMOBILIZER
CONTROL SYSTEM

Do not turn ON ignition switch with ignition key for immobilizer
control system put together with another one or placed quite close
to another one. Or the system may detect abnormal condition and
prevent engine from starting.

Do not turn ON ignition switch by using ignition key with any type
of metal wound around its grip or in contact with it. Or the system
may detect abnormal condition and prevent engine from starting.

Do not leave ignition key where high temperature is anticipated.
High temperature will cause transponder in ignition key to be ab-
normal or damaged.

Do not turn ON ignition switch with a radio antenna placed near
coil antenna or its harness to Immobilizer Control Module. Or the
system may detect abnormal condition and prevent engine from
starting.

YH4
GRAND
VITARA
(A)(A)
(A)
10B-6 AIR BAG SYSTEM
DIAGNOSIS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
DIAGNOSTIC TROUBLE CODES
The ªAir Bag Diagnostic System Checkº must always be the starting point of any air bag system diagnosis. The
ªAir Bag Diagnostic System Checkº checks for proper ªAIR BAGº warning lamp operation and checks for air bag
diagnostic trouble codes using the Tech-1 (scan tool) or on-board diagnosis function.

Current diagnostic trouble code ± Malfunction that are presently being detected.

History diagnostic trouble code ± All malfunction detected since the last time the history memory was cleared.
USE OF SPECIAL TOOLS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
You should be familiar with the tools listed under ªSpecial Toolsº in this section. You should be able to measure
voltage and resistance. You should be familiar with proper use of a scan tool such as the Tech-1 Diagnostic Com-
puter, Driver/Passenger Load Tool, Connector Test Adapter Kit and the Digital Multimeter.
Special Tool (Connector Test Adapter Kit)
(A): 09932-76010
This must be used whenever a diagnostic procedure requests
checking or probing a terminal.
Using the appropriate adapter in the special tool will ensure that no
damage to the terminal will occur from the multimeter probe, such
as spreading or bending.
The adapter will also give an idea of whether contact tension is suffi-
cient, helping to find an open or intermittent open due to poor termi-
nal contact.

YH4
GRAND
VITARA
10B-10 AIR BAG SYSTEM
AIR BAG DIAGNOSTIC SYSTEM CHECK
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
CAUTION:
The order in which diagnostic trouble codes are diagnosed is very important. Failure to diagnose the
diagnostic trouble codes in the order specified may result in extended diagnostic time, incorrect diag-
nosis and incorrect parts replacement.
The diagnostic procedures used in this section are designed to find and repair air bag system malfunctions.
To get the best results, it is important to use the diagnostic flow tables and follow the sequence listed below.
A. PERFORM THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº
The ªAir Bag Diagnostic System Check Flow Tableº must be the starting point of any air bag system diagnostics.
The ªAir Bag Diagnostic System Check Flow Tableº checks for proper ªAIR BAGº warning lamp operation, the
ability of the SDM to communicate through ªAIR BAGº warning lamp and whether air bag diagnostic trouble
codes exist.
B. REFER TO THE PROPER DIAGNOSTIC TABLE AS DIRECTED BY THE ªAIR BAG DIAGNOSTIC SYSTEM
CHECK FLOW TABLEº.
The ªAir Bag Diagnostic System Check Flow Tableº will lead you to the correct chart to diagnose any air bag
system malfunctions. Bypassing these procedures may result in extended diagnostic time, incorrect diagnosis
and incorrect parts replacement.
C. REPEAT THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº AFTER ANY REPAIR OR DIAGNOS-
TIC PROCEDURES HAVE BEEN PERFORMED.
Performing the ªAir Bag Diagnostic System Check Flow Tableº after all repair or diagnostic procedures will en-
sure that the repair has been made correctly and that no other malfunctions exist.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-55
ON-VEHICLE SERVICE
SERVICE PRECAUTIONS
SERVICE AND DIAGNOSIS
WARNING/CAUTION labels are attached on each part of air bag system components (SDM, air bag (inflator) mod-
ules and seat belt pretensioners). Be sure to follow the instructions.
WARNING:

If the air bag system and another vehicle system both need repair, Suzuki recommends that the air
bag system be repaired first, to help avoid unintended air bag system activation.

Do not modify the steering wheel, dashboard or any other air bag system components. Modifications
can adversely affect air bag system performance and lead to injury.

Failure to follow procedures could result in possible air bag system activation, personal injury or un-
needed air bag system repairs.

Many of service procedures require disconnection of ªAIR BAGº fuse and air bag (inflator) modules (driver and
passenger) from initiator circuit to avoid an accidental deployment.

Do not apply power to the air bag system unless all components are connected or a diagnostic chart requests
it, as this will set a diagnostic trouble code.

The ªAir Bag Diagnostic System Checkº must be the starting point of any air bag diagnostics. The ªAir Bag Diag-
nostic System Checkº will verify proper ªAIR BAGº warning lamp operation and will lead you to the correct chart
to diagnose any air bag malfunctions. Bypassing these procedures may result in extended diagnostic time, incor-
rect diagnosis, and incorrect parts replacements.

Never use air bag component parts from another vehicle.

If the vehicle will be exposed to temperatures over 93
C (200
F) (for example, during a paint baking process),
remove the air bag system components beforehand to avoid component damage or unintended system activa-
tion.

When servicing, if shocks may be applied (eg., dropped from a height of 90 cm (3 ft) or more) to air bag system
component parts, remove those parts beforehand.

When using electric welding, be sure to disconnect air bag (inflator) module and seat belt pretensioner connec-
tors (driver and passenger) respectively.

When applying paint around the air bag system related parts, use care so that the harness or connector will not
be exposed to the paint mist.

Never expose air bag system component parts directly to hot air (drying or baking the vehicle after painting) or
flames.
WARNING:
When performing service on or around air bag system components or air bag wiring, follow the proce-
dures listed in the following pages to temporarily disable the air bag system. Refer to appropriate ser-
vice manual procedures. Failure to follow procedures could result in possible air bag system activa-
tion, personal injury or unneeded air bag system repairs.

YH4
GRAND
VITARA
1. SDM
2. SDM bolt
3. SDM cover
4. SDM connector1. Front center console box
2. Center garnish panel
3. Ashtray
4. Radio hole cover
5. Clock assembly
AIR BAG SYSTEM 10B-67
SDM
WARNING:
During service procedures, be very careful when handling
a Sensing and Diagnostic Module (SDM).
Be sure to read ªService Precautionsº in this section before
starting to work and observe every precaution during work.
Neglecting them may result in personal injury or inactiva-
tion of the air bag system when necessary.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº ear-
lier in this section.
3) Remove rear and front center console box by removing screw
and clips.
4) Remove center garnish panel.
5) Remove ashtray and tuner assembly, clock assembly, tuner
pocket, radio hole cover, etc.
6) Disconnect SDM connector from SDM.
7) Remove SDM (with SDM plate) as an assembly from vehicle.
NOTE:
Do not separate SDM and SDM plate.
INSPECTION
CAUTION:

Do not connect a tester whatever type it may be.

Never repair or disassemble SDM.

If SDM was dropped from a height of 90 cm (3 ft) or more,
it should be replaced.

Check SDM and SDM plate for dents, cracks or deformation.

Check SDM connector for damage, cracks or lock mechanism.

Check SDM terminal for bent, corrosion or rust.
If any faulty condition is found in above checks, replace.

YH4
GRAND
VITARA
1. Passenger air bag (inflator) module
2. Instrument panel
3. Glove box
1. Glove box
2. Push
3. Pull
AIR BAG SYSTEM 10B-69
PASSENGER AIR BAG (INFLATOR) MODULE
WARNING:

Never attempt to disassemble or repair the passenger air bag (inflator) module. If any abnormality is
found, be sure to replace it with new one as an assembly.

Be sure to read ªService Precautionsº in this section before starting to work and observe every pre-
caution during work. Neglecting them may result in personal injury or undeployment of the air bag
when necessary.
REMOVAL
1) Disconnect negative battery cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº ear-
lier in this section.
3) Open glove box, then while pressing glove box stopper, pull out
glove box from instrument panel.
4) Remove glove box from instrument panel.
5) Remove passenger air bag (inflator) module attaching bolts and
screws, and passenger air bag (inflator) module from vehicle.
WARNING:

When carrying a live air bag (inflator) module, make
sure the bag opening is pointed away from you.
Never carry air bag (inflator) module by wires or con-
nector on the side of the module. In case of an acciden-
tal deployment, the bag will then deploy with minimal
chance of injury.

As the live passenger air bag (inflator) module must be
kept with its bag (trim cover) facing up while being
stored or left standing, place it on the workbench with
a slit or use the workbench vise to hold it securely at its
lower mounting bracket. This is necessary so that a
free space is provided to allow the air bag to expand in
the unlikely event of accidental deployment.

Observe ªService Precautionsº earlier in this section
for handling and storing it.
Otherwise personal injury may result.