2005 SUZUKI GRAND VITARA lock

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-39
1. Rear axle
2. Retainer ring
3. Sensor rotor
4. Vinyl envelope
ªAº Grind with grinderªAº
1. Sensor rotor 4
31
2
2 1
3
REAR SENSOR ROTOR
REMOVAL
1) Remove rear axle shaft. Refer to REAR AXLE SHAFT RE-
MOVAL in Section 3E.
2) In order to remove sensor rotor from retainer ring, grind with a
grinder one part of the sensor rotor as illustrated till it becomes
thin.
CAUTION:

Cover vinyl sheet or the like over wheel bearing so that
fine grains from grinding will not enter there.

Be careful not to go so far as to grind the retainer ring.
3) Break with a chisel the thin ground sensor rotor, and it can be re-
moved.
INSTALLATION
1) Press-fit sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
2) Install rear axle shaft. Refer to REAR AXLE SHAFT INSTALLA-
TION in Section 3E.

YH4
GRAND
VITARA
5E1-40 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Parking brake
lever ass'y
2. G sensor
3. Bolt ª1º
4. Bolt ª2º
[A] Horizontal
[B] Upright with
arrow upward
[C] Upright with
arrow downward
A: Forward
G SENSOR (FOR 4WD MODEL ONLY)
REMOVAL
1) Turn ignition switch OFF and disconnect battery negative cable.
2) Remove rear center console box.
3) Remove parking brake lever bolts ª1º and G sensor with bracket
from floor.
NOTE:
Loosen only bolt ª2º.
4) Remove sensor with bracket from floor.
5) Disconnect connector from sensor.
CAUTION:

Do not separate sensor and bracket. It will lead to erro-
neous assembly.

Sensor must not be dropped or shocked. It will affect its
original performance.
INSPECTION
1) Check sensor bracket for bend.
2) Connect positive cable of 12 volt battery to ªAº terminal of sensor
and ground cable to ªCº terminal. Then using voltmeter, check
voltage between ªBº terminal and ªCº terminal.
When placed horizontally: 2 ± 3 V
When placed upright with arrow upward: 3 ± 4 V
When placed upright with arrow downward: 1 ± 2 V
If measured voltage is not as specified, replace sensor with
bracket.
INSTALLATION
1) Connect connector to sensor securely.
2) Install sensor with bracket and parking lever assy onto floor so
that arrow mark directs vehicle forward.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Install rear console box.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-41
(d)
TRANSFER 4WD SWITCH
For removal, inspection and installation of this switch, refer to
SWITCHES in Section 7A.
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe flare nut: (a)161.611.5
ABS hydraulic unit nut: (b)212.115.5
ABS hydraulic unit bracket bolt: (c)101.07.5
Wheel speed sensor bolt(Front): (d)232.317.0Wheel s eed sensor bolt(Rear): (e)212.115.5
Parking lever assy mounting bolt: (f)232.317.0

YH4
GRAND
VITARA
5E1-42 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
09950-78220
Flare nut wrench
(10 mm)09931-76011
SUZUKI scan tool (Tech 1A) kit1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
5. Test lead / probe
6. Power source cable
7. DLC cable adapter
8. Self-test adapter
Mass storage cartridge
09931-76030
16 / 14 pin DLC cable
SPECIAL TOOLS

YH4
GRAND
VITARA
1. Bolt
2. Console box
bracket
3. Boot cover
1. Boot No. 3
2. Boot cover
3. Boot No. 2
4. Control lever
5. Lever case
6. Control case cover
7. Boot No. 1
1. Transmission control
lever locating bolt
2. Transfer control lever
locating bolt
7A-4 MANUAL TRANSMISSION (TYPE 1)
SHIFT CONTROL LEVERS
REMOVAL
1) Remove 4 screws at the front and rear and 2 clips at the center
then take off front and rear center console boxes.
NOTE:
To remove clip, push in its center pin first.
2) Remove console box bracket by removing bolts and lift up boot
cover and boot No. 2.
3) Remove boot clamp and then remove boot No. 1 from transmis-
sion shift lever case.
4) With gear shift control case cover pushed down with fingers, turn
it to counter clockwise and take out shift control lever.
5) Take out transfer shift control lever in similar manner as de-
scribed above.
INSPECTION AND INSTALLATION
1) Check shift control lever lower portion and control lever locating
sheet for excessive wear, and boot for damage. Correct or re-
place if necessary.
2) Apply grease to pivot portions and seat, then install shift control
lever.
ªAº: Grease 99000-25010
3) Perform above steps also for transfer shift control lever.
4) If control lever locating bolts (a) are replaced or retightened,
torque them as specified below.
Replacing of control lever locating bolts requires thread lock ce-
ment.
ªBº: Cement 99000-32020
Tightening Torque
(a): 17 N
.m (1.7 kg-m, 12.5 lb-ft)

YH4
GRAND
VITARA
7A-14 MANUAL TRANSMISSION (TYPE 1)
09951-16060
Oil seal installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back up light switch (Type 1)202.014.5
Back up light switch (Type 2)454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts and nut505.036.5
Exhaust center pipe to manifold nuts505.036.5
Muffler to exhaust center pipe bolts505.036.5
Universal joint flange bolts505.036.5
Select return spring bolts232.317.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever.

Select return springs, bolts and guides.
Thread lock cementTHREAD LOCK CEMENT
SUPER 1333B (99000-32020)
Shift control lever locating bolts.
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil Drain and filler / level plugs.
SPECIAL TOOL

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 2) 7A1-5
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN´mkg-mlb-ft
Transfer oil filler / level and drain plugs232.317.0
Transmission oil filler / level and drain plugs383.827.5
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back-up light switch454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts505.036.5
Muffler to exhaust No. 2 pipe nuts505.036.5
Universal joint flange bolts505.036.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever
Thread lock cement
THREAD LOCK CEMENT
SUPER 1333B
(99000-32020)

Shift control lever locating bolts
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil drain and filler / level plugs

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS