2005 SUZUKI GRAND VITARA Rear

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-39
1. Rear axle
2. Retainer ring
3. Sensor rotor
4. Vinyl envelope
ªAº Grind with grinderªAº
1. Sensor rotor 4
31
2
2 1
3
REAR SENSOR ROTOR
REMOVAL
1) Remove rear axle shaft. Refer to REAR AXLE SHAFT RE-
MOVAL in Section 3E.
2) In order to remove sensor rotor from retainer ring, grind with a
grinder one part of the sensor rotor as illustrated till it becomes
thin.
CAUTION:

Cover vinyl sheet or the like over wheel bearing so that
fine grains from grinding will not enter there.

Be careful not to go so far as to grind the retainer ring.
3) Break with a chisel the thin ground sensor rotor, and it can be re-
moved.
INSTALLATION
1) Press-fit sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
2) Install rear axle shaft. Refer to REAR AXLE SHAFT INSTALLA-
TION in Section 3E.

YH4
GRAND
VITARA
5E1-40 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Parking brake
lever ass'y
2. G sensor
3. Bolt ª1º
4. Bolt ª2º
[A] Horizontal
[B] Upright with
arrow upward
[C] Upright with
arrow downward
A: Forward
G SENSOR (FOR 4WD MODEL ONLY)
REMOVAL
1) Turn ignition switch OFF and disconnect battery negative cable.
2) Remove rear center console box.
3) Remove parking brake lever bolts ª1º and G sensor with bracket
from floor.
NOTE:
Loosen only bolt ª2º.
4) Remove sensor with bracket from floor.
5) Disconnect connector from sensor.
CAUTION:

Do not separate sensor and bracket. It will lead to erro-
neous assembly.

Sensor must not be dropped or shocked. It will affect its
original performance.
INSPECTION
1) Check sensor bracket for bend.
2) Connect positive cable of 12 volt battery to ªAº terminal of sensor
and ground cable to ªCº terminal. Then using voltmeter, check
voltage between ªBº terminal and ªCº terminal.
When placed horizontally: 2 ± 3 V
When placed upright with arrow upward: 3 ± 4 V
When placed upright with arrow downward: 1 ± 2 V
If measured voltage is not as specified, replace sensor with
bracket.
INSTALLATION
1) Connect connector to sensor securely.
2) Install sensor with bracket and parking lever assy onto floor so
that arrow mark directs vehicle forward.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Install rear console box.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-41
(d)
TRANSFER 4WD SWITCH
For removal, inspection and installation of this switch, refer to
SWITCHES in Section 7A.
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe flare nut: (a)161.611.5
ABS hydraulic unit nut: (b)212.115.5
ABS hydraulic unit bracket bolt: (c)101.07.5
Wheel speed sensor bolt(Front): (d)232.317.0Wheel s eed sensor bolt(Rear): (e)212.115.5
Parking lever assy mounting bolt: (f)232.317.0

YH4
GRAND
VITARA
7A
MANUAL TRANSMISSION (TYPE 1) 7A-1
TYPE 1
GENERAL DESCRIPTION7A- 1 . . . . . . . . . . . . . .
DIAGNOSIS7A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A- 3 . . . . . . . . . . . . . . . .
Gear Oil 7A- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A- 4. . . . . . . . . . . . . . . . . . .
Switches 7A- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A- 8. . . . . . . . . . . . . . . .
Dismounting of Trans. Unit 7A- 9. . . . . . . . . . . . .
Remounting of Trans. Unit 7A-12. . . . . . . . . . . . . Extension Case (2WD MODEL) 7A-13. . . . . . . .
Extension Case Oil Seal
(2WD MODEL) 7A-13. . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A-14 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A-14 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A-14 . . . . . .
SPECIAL TOOL7A-14 . . . . . . . . . . . . . . . . . . . . . . .
As the aluminum case is sealed with liquid type gas-
ket, it is necessary to use genuine sealant or its equiv-
alent on its mating surfaces when reassembling it.
Also, the case fastening bolts must be tightened to
specified torque by means of the torque wrench and
tightening over or below the specified torque should
be avoided.
The description under ON-VEHICLE SERVICE in this
section covers a part of the TYPE 2 manual transmis-
sion and the transfer. The transfer is next to the trans-
mission as well, but their gear boxes are independent
and each of them has its own drain and level / filler
plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A
MANUAL TRANSMISSION
(TYPE 1)
CONTENTS
GENERAL DESCRIPTION
The manual transmission consists of the input shaft,
main shaft, countershaft and reverse gear which are
installed in the aluminum case. Its gears are of for-
ward five speeds in synchro mesh and reverse one
speed in constant mesh system.
The main shaft gears are held by the needle bearings
and on them the synchronizer rings and synchronizer
sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.

YH4
GRAND
VITARA
1. Bolt
2. Console box
bracket
3. Boot cover
1. Boot No. 3
2. Boot cover
3. Boot No. 2
4. Control lever
5. Lever case
6. Control case cover
7. Boot No. 1
1. Transmission control
lever locating bolt
2. Transfer control lever
locating bolt
7A-4 MANUAL TRANSMISSION (TYPE 1)
SHIFT CONTROL LEVERS
REMOVAL
1) Remove 4 screws at the front and rear and 2 clips at the center
then take off front and rear center console boxes.
NOTE:
To remove clip, push in its center pin first.
2) Remove console box bracket by removing bolts and lift up boot
cover and boot No. 2.
3) Remove boot clamp and then remove boot No. 1 from transmis-
sion shift lever case.
4) With gear shift control case cover pushed down with fingers, turn
it to counter clockwise and take out shift control lever.
5) Take out transfer shift control lever in similar manner as de-
scribed above.
INSPECTION AND INSTALLATION
1) Check shift control lever lower portion and control lever locating
sheet for excessive wear, and boot for damage. Correct or re-
place if necessary.
2) Apply grease to pivot portions and seat, then install shift control
lever.
ªAº: Grease 99000-25010
3) Perform above steps also for transfer shift control lever.
4) If control lever locating bolts (a) are replaced or retightened,
torque them as specified below.
Replacing of control lever locating bolts requires thread lock ce-
ment.
ªBº: Cement 99000-32020
Tightening Torque
(a): 17 N
.m (1.7 kg-m, 12.5 lb-ft)

YH4
GRAND
VITARA
1. Engine rear mounting member
2. Mounting bracket
3. Engine rear mounting FRONT SIDE
REAR SIDE
7A-8 MANUAL TRANSMISSION (TYPE 1)
ENGINE REAR MOUNTING
When replacement of mounting parts are necessary, torque bolts
and nut as specified below.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
1. Transmission
2. Breather clamp
3. Breather hose
4. Wiring harness clamp
5. Intake manifold
MANUAL TRANSMISSION (TYPE 1) 7A-9
DISMOUNTING OF TRANS. UNIT
IN CABIN
Remove transmission shift control lever (refer to page 7A-4) and
transfer shift control lever knob.
IN ENGINE ROOM
1) Disconnect negative (±) cable of battery.
2) Remove breather hose from clamp at the rear end of cylinder
head.
3) Remove starting motor fixing bolts and nut and then remove
starter.
4) Remove transmission fastening bolts.

YH4
GRAND
VITARA
1. Match mark
1. Flange bolt
2. Front propeller shaft
1. Transmission jack
2. Engine rear mounting member
7A-10 MANUAL TRANSMISSION (TYPE 1)
ON LIFT
1) Drain oil from transmission and transfer.
2) Give match marks on joint flange and propeller shaft as shown
in figure. (front and rear)
3) Remove flange bolts of rear propeller shaft universal joint and
pull out propeller shaft.
4) Remove flange bolts of front propeller shaft universal joint and
pull out propeller shaft.
5) Remove clutch operating cylinder from transmission. It is not
necessary to disconnect clutch hose from operating cylinder.
NOTE:

It is not necessary to drain transmission oil when dis-
mounting transmission and transfer for clutch mainte-
nance only.

Work without draining transfer oil is possible if front pro-
peller shaft is dismounted together with transmission and
transfer.
6) Remove clutch housing lower plate.
7) Disconnect couplers from 4WD switch, back up light switch and
speed sensor assembly and release their harness from clamps.
Remove nuts from joint with engine.
8) Apply transmission jack and remove engine rear mounting
member taking off its bolts.
9) After removing mounting member, move rearward transmission
and transfer assemblies placed on jack and then lower them.