2005 SUBARU IMPREZA WRX maintenance

11 - 7 4
Maintenance and service
2. Pull the bulb out of the socket. Install a new bulb.
3. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
4. Install the headlight assembly and the front grille in
the reverse order of removal.
„
Parking light
1) Parking light
The headlight assembly must be removed before the
parking light bulbs can be replaced. When the head-
light assembly has been removed and then rein-
stalled, it may become necessary to make a headlight
aiming adjustment. It may be difficult to replace the
bulbs. Have your SUBARU dealer replace the bulbs ifnecessary.
UGB531BA
1
UGB523BB

11 -7 5
Maintenance and service
– CONTINUED –
TBefore removing the headlight assembly0
1. Loosen four clips at the top of the front bumper. c
:Clip
… : Hook
UGB525BA
UGB528BA

11 - 7 6
Maintenance and service
2. Remove the front grille. Use a screwdriver to de-
tach the four clips at the top and the two hooks on
each side.
T
Removal of headlight assembly
UGB529BA
UGB534BA
UGB533CA

11 -7 7
Maintenance and service
– CONTINUED –
1. Remove two bolts and disconnect connectors.
2. Pull the headlight assembly toward you and re-
move it from the vehicle. T
Parking light bulbs
1. Remove the bulb socket from the headlight assem-
bly by turning it counterclockwise.
UGB551BAUGB535BA

11 - 7 8
Maintenance and service
2. Pull the bulb out of the socket. Install a new bulb.
3. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
4. Install the headlight assembly and the front grille in
the reverse order of removal. „
Front fog light
It may be difficult to replace the bulbs. Have your
SUBARU dealer replace the bulbs if necessary. „
Rear combination lights
T Sedan
1. Remove the clip from the rear trunk trim with a
screwdriver.
UGB532BA
UGB538BA

11 -7 9
Maintenance and service
– CONTINUED –
1) Backup light
2) Rear turn signal light
3) Brake/tail light
4) Tail light
5) Brake light
2. Open the rear portion of the side trunk trim panel.
3. Remove the bulb holder from the rear combination
light assembly by turning it counterclockwise.
4. Remove the bulb from the socket by pushing it and
turning counterclockwise. Install a new bulb.
5. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
6. Secure the rear trunk trim panel with the clips. T
Wagon
1. Using a Phillips screwdriver, remove the upper and
lower screws that secure the side cover of the rear
combination light assembly.
554
2
3
1
UGB539BB
UGB540BA

11 - 8 0
Maintenance and service
2. Remove the upper and lower screws. Then, slide
the rear combination lamp assembly to the rear and
remove it from the vehicle.
1) Brake/tail light
2) Rear turn signal light
3) Backup light
3. Remove the bulb holder from the rear combination
light assembly by turning it counterclockwise.
4. Remove the bulb from the socket by pushing it and
turning counterclockwise. Install a new bulb.
5. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
6. Close the cover and latch the lock.
7. Reinstall the rear combination light assembly and
its side cover.
UGB541BA
2
1
3
UGB542BB

11 -8 1
Maintenance and service
– CONTINUED –
„License plate light
1. Remove the mounting screws using a Phillips
screwdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws. „
Dome light, map light and cargo area
light
UGB136BA
HSB088BA