2005 SUBARU FORESTER tires

11 -4 9
Maintenance and service
– CONTINUED –
placing all four tires at the same time.
yAll four tires must be the same in terms of
manufacturer, brand (tread pattern), construc-
tion, degree of wear, speed symbol, load index
and size. Mixing tires of different types, sizes or
degrees of wear can result in damage to vehi-
cle’s power train. Use of different types or sizes
of tires can also dangerously reduce controlla-
bility and braking performance and can lead to
an accident.y Use only radial tires. Do not use radial tires
together with belted bias tires and/or bias-ply
tires. Doing so can dangerously reduce control-
lability, resulting in an accident.
„ Wheel replacement
When replacing wheels due, for example, to damage,
make sure the replacement wheels match the specifi-
cations of the wheels that are fitted as standard equip-
ment. Replacement wheels are available from
SUBARU dealers.
Use only those wheels that are specified for
your vehicle. Wheels not meeting specifica-
tions could interfere with brake caliper opera-
tion and may cause the tires to rub against the
wheel well housing during turns. The resulting
loss of vehicle control could lead to an acci-
dent.

12-1
12
Specifications
Specifications ................................................ 12-2 Dimensions ....................................................... 12-2
Engine ................................................................ 12-3
Electrical system .............................................. 12-3
Capacities .......................................................... 12-4
Tires ................................................................... 12-5
Wheel alignment ............................................... 12-5
Fuses and circuits ........................................ 12-6 Fuse panel located behind the coin tray ........ 12-6
Fuse panel located in the engine compartment .................................................. 12-8
Bulb chart ...................................................... 12-9
Vehicle identification .................................... 12-10

12-5
Specifications
– CONTINUED –
„Tires
„ Wheel alignment
Tire sizeP215/60R16 94H
Wheel size16 × 6 1
/2 JJ
PressureFrontLight load29 psi (200 kPa, 2.0 kgf/cm 2
)
Full load29 psi (200 kPa, 2.0 kgf/cm 2
)
RearLight load28 psi (190 kPa, 1.9 kgf/cm 2
)
Full load36 psi (250 kPa, 2.5 kgf/cm 2
)
Trailer towing41 psi (280 kPa, 2.8 kgf/cm 2
)
Item2.5-liter non-turbo models2.5-liter turbo models
Drive systemAWD
ToeFront0 ± 0.12 in (0 ± 3 mm)
Rear0.08 ± 0.12 in (2 ± 3 mm)
CamberFront–0 °25’ ± 45’
Rear–0 °50’ ± 45’–0 °55’ ± 45’

13-1
13
Consumer information and Reporting safety defectsTire information ............................................. 13-2Tire labeling ....................................................... 13-2
Recommended tire inflation pressure ............ 13-5
Glossary of tire terminology ............................ 13-7
Tire care – maintenance and safety practices .............................................. 13-8
Vehicle load limit – how to determine ............. 13-9
Determining compatibility of tire and vehicle
load capacities ............................................... 13-13
Adverse safety consequences of overloading on handling and stopping and on tires ........ 13-14
Steps for Determining Correct Load Limit ..... 13-14
Uniform tire quality grading standards ....... 13-15 Treadwear .......................................................... 13-15
Traction AA, A, B, C .......................................... 13-15
Temperature A, B, C ......................................... 13-16
Reporting safety defects (USA) ................... 13-17

13-3
Consumer information and Reporting safety defects
– CONTINUED –
Example:
(6) Load Index: A numerical code which speci-
fies the maximum load a tire can carry at the
speed indicated by its speed symbol, at maxi-
mum inflation pressure.
For example, “94” means 1,477 lbs (670 kg).
Load indices apply only to the tire, not to
the vehicle. Putting a load rated tire on any
vehicle does not mean the vehicle can be
loaded up to the tire’s rated load.
(7) Speed Rating: An alphabetical system de-
scribing a tire’s capability to travel at established
and predetermined speeds.
For example, “H” means 130 mph (210 km/h)
y Speed ratings apply only to the tire, not
to the vehicle. Putting a speed rated tire on
any vehicle does not mean the vehicle can
be operated at the tire’s rated speed. y The speed rating is void if the tires are
worn out, damaged, repaired, retreaded, or
otherwise altered from their original condi-
tion. If tires are repaired, retreaded, or oth-
erwise altered, they may not be suitable for
original equipment tire designed loads and
speeds.
T Tire Identification Number (TIN)
Tire Identification Number (TIN) is marked on the
intended outboard sidewall. The TIN is com-
posed of four groups. Here is a brief review of the
TIN with a breakdown of its individual elements.
(1) Manufacturer’s Identification Mark
P 215 / 60 R 16 94 H Size designation (6) (7)
DOT XX XX XXX XXXX
(1) (2) (3)(4)

13-5
Consumer information and Reporting safety defects
– CONTINUED –
„Recommended tire inflation pressure
T Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire sizeP215/60R16 94H
Wheel size16 × 6 1
/2 JJ
PressureFrontLight load29 psi (200 kPa, 2.0 kgf/cm 2
)
Full load29 psi (200 kPa, 2.0 kgf/cm 2
)
RearLight load28 psi (190 kPa, 1.9 kgf/cm 2
)
Full load36 psi (250 kPa, 2.5 kgf/cm 2
)
Trailer towing41 psi (280 kPa, 2.8 kgf/cm 2
)

13-6
Consumer information and Reporting safety defects
T
Vehicle placard
The vehicle placard is affixed to the driver’s side door pillar. Example:
The vehicle placard shows original tire size, rec-
ommended cold tire inflation pressure on each
tire at maximum loaded vehicle weight, seating
capacity and loading information. T
Adverse safety consequences of under-in-
flation
Driving at high speeds with excessively low tire
pressures can cause the tires to flex severely
and to rapidly become hot. A sharp increase in
temperature could cause tread separation, and
failure of the tire(s). Possible resulting loss of ve-
USD508BAKL
TIRE AND LOADING INFORMATIONSEATING CAPACITY : TOTAL 5
ORIGINAL TIRE SIZE
SEE OWNER’S MANUAL FOR
ADDITIONAL INFORMATION
COLD TIRE
INFLATION PRESSRE
COLD TIRE
INFLATION PRESSRE
FRONT
REAR200kPa,29PSI 190kPa,28PSIP215/60R16 P215/60R16
200kPa, 29PSI
SPARE TIRE
The combined weight of occupants andcargo should never exceed 408kg or 900lbs.
FRONT 2 : REAR 3
USD507AA

13-7
Consumer information and Reporting safety defects
– CONTINUED –
hicle control could lead to an accident. TMeasuring and adjusting air pressure to
achieve proper inflation
Check and, if necessary, adjust the pressure of
each tire (including the spare) at least once a
month and before any long journey. Check the
tire pressures when the tires are cold. Use a
pressure gauge to adjust the tire pressures to the
specific values. Driving even a short distance
warms up the tires and increases the tire pres-
sures. Also, the tire pressures are affected by the
outside temperature. It is best to check tire pres-
sure outdoors before driving the vehicle. When a
tire becomes warm, the air inside it expands,
causing the tire pressure to increase. Be careful
not to mistakenly release air from a warm tire to
reduce its pressure. „ Glossary of tire terminology
y Cold tire pressure
The pressure in a tire that has been driven less
than 1 mile or has been standing for three hours
or more. y Maximum inflation pressure The maximum cold inflation pressure to which a
tire may be inflated. y
Recommended inflation pressure
The cold inflation pressure recommended by a
vehicle manufacturer. y Intended outboard sidewall
1)The sidewall that contains a whitewall, bears
white lettering or bears manufacturer, brand,
and/or model name molding that is higher or
deeper than the same molding on the other
sidewall of the tire, or
2)The outward facing sidewall of an asymmet-
rical tire that has a particular side that must al-
ways face outward when mounting on a vehi- cle.
y Accessory weight
The combined weight (in excess of those stan-
dard items which may be replaced) of floor mats,
leather seats and cross bars to the extent that
these items are available as factory-installed
equipment (whether installed or not). y Curb weight
The weight of a motor vehicle with standard
equipment including the maximum capacity of fu-
el, oil, and coolant and air conditioning.