2005 SUBARU BAJA lock

2-20
Keys and doors
DISARM” button on the transmitter. T
Tripped sensor identification
If an electronic chirp sounds four times and the turn
signal lights flash four times when you disarm the sys-
tem, this indicates that the alarm was triggered. The
number of times the indicator light flashes indicates
what sensor caused the alarm condition.
To enter identification mode:
1. Open the driver’s door and leave it open.
2. Turn the ignition switch to “ON” twice. (“LOCK”
“ON” “LOCK” “ON” “LOCK”)
3. The indicator light will start flashing.
The indicator light provides the following indications.
Flashing once: Any door has been opened.
Flashing three times: The impact sensor in the sys-
tem’s unit has been activated. This may indicate that
your vehicle has been shocked or tampered with by
some outside force and/or unauthorized person.
Flashing four times: The ignition switch has been
turned on or the battery has been disconnected.
NOTE
The battery must be reconnected before the indi-
cator light will flash.
To exit this mode, close the door and turn the ignition switch to “ON”.

2-21
Keys and doors
– CONTINUED –
Child safety locks
Always use the child safety lock whenever a
child rides in the rear seat. Serious injury could
result if a child accidentally opened the door
and fell out.
1) Lock
2) Unlock
Each rear door has a child safety lock that prevents the doors from being opened even if the inside door
handle is pulled.
When the child safety lock lever is in the lock position,
the door cannot be opened from inside regardless of
the position of the inner door handle lock lever. The
door can only be opened from the outside.
1
2
UB2002BB

2-22
Keys and doors
Windows „
Power windows
To avoid serious personal injury caused by en-
trapment, you must do the following.yWhen operating the power windows, be ex-
tremely careful to prevent anyone’s fingers,
arms, neck or head from being caught in the
window. y Always lock the passengers’ windows using
the lock switch when children are riding in the
vehicle. y Before leaving the vehicle, always remove
the key from the ignition switch for safety and
never allow an unattended child to remain in
the vehicle. Failure to follow this procedure
could result in injury to a child operating the
power window.
The power windows operate only when the ignition
switch is in the “ON” position. T
Driver’s side switches
1) Lock switch
2) For driver’s window
3) For rear left passenger’s window
4) For front passenger’s window
5) For rear right passenger’s window
All door windows can be controlled by the power win-
dow switch cluster at the driver side door.
1
2
3 4
5
UB2008BB

2-23
Keys and doors
– CONTINUED –
VOperating the driver’s window
1) Lock
2) Unlock
3) Close
4) Open
5) Automatically open
To open:
Push the switch down lightly and hold it. The window
will open as long as the switch is held.
This switch also has a one-touch auto down feature
that allows the window to be opened fully without hold-
ing the switch.
Push the switch down until it clicks and release it, and
the window will fully open. To stop the window half- way, pull the switch up lightly.
To close:
Pull the switch up lightly and hold it. The window will
close as long as the switch is held. V
Operating the passengers’ windows
To open the passengers’ windows, push the appropri-
ate switch down and hold it until the window reaches
the desired position. To close the window, pull the
switch up and hold it until it reaches the desired posi-
tion. V Locking the passengers’ windows
To lock the passengers’ windows, push the lock
switch. When the lock switch is in the “LOCK” position,
the passengers’ windows cannot be opened or closed.
1 2 3
4
5 3
4
UB2008DB

2-24
Keys and doors
T
Passengers’ side switches
Front passenger’s window switch
1) Open
2) Close Rear passenger’s window switches
1) Open
2) Close
To open the window, push the switch down and hold it
until the window reaches the desired position. To
close the window, pull the switch up and hold it until
the window reaches the desired position.
When the lock switch on the power window switch
cluster, located on the driver’s side door, is in the
“LOCK” position, the passengers’ windows cannot be
operated with the passengers’ switches.
1 2UB2009CB
2
1
UB2005BB

2-28
Keys and doors
Pay attention that your fingers do not get
pinched with the switchback door when open-
ing and closing it.
To open the switchback door:
1. Pull up the rear seat cushion. Refer to “Rear seats”
section in Chapter 1 for operating details. 1) Red
A) LOCK
B) UNLOCK
UB1172BA
1
AB
UB1112CB

2-29
Keys and doors
– CONTINUED –
2. Unlock the rear seatback by pulling up on the knob
and fold down the rear seatback. Confirm that the pins
located at the bottom of the seat cushion is inserted
into the slots at the top of the seatback.
3. Fold down the switchback door by releasing the
UB1113BAUB1114BA
UB1115BA

2-30
Keys and doors
lock knob. Then you can have a flat and larger cargo
space.
4. Place the long object on the cargo bed through the
switchback door opening.
Be sure all items are secured in place.
NOTE y
When opening the switchback door in snow, ac-
cumulated snow in the cargo bed may enter the
passenger compartment which could result in
dampness in the passenger compartment. Prior to
opening of the switchback door, brush off the
snow completely.y Close the switchback door whenever you leave
the vehicle to prevent unauthorized entry.
The switchback door should be kept complete-
ly shut when the vehicle is idling in an enclosed
or partially enclosed area to avoid the possibil-
ity of exhaust gas entering the passenger com-
partment. Engine exhaust gas contains carbon
monoxide, a colorless and odorless gas which
is extremely dangerous, or even lethal if in-
haled. To ensure that exhaust gas cannot pen-
etrate the switchback door, make certain that
there are no obstructions between the door and the vehicle body that prevent the door from ful-
ly closing or that crimp the weather strip
around the door.
To close the switchback door, firmly push it upward
until it latches.
Return the seatback and seat cushion to their original
positions and make sure they are securely locked.
After returning the seatback to its original posi-
tion, make sure that the rear seatback has been
securely locked. When securely locked, the red
marks on the locking knobs are no longer visi-
ble.