2005 Seat Alhambra warning light

Opening and closing73
Safety FirstControls and equipment Tips and Maintenance Technical Data
Foldable key*
T To
o uun
nf
fo
ol
ld
d
the key sword, press button A. It will unfold with a
spring.
T To
o ffo
ol
ld
d
the key sword, press button
Aand guide it with your hand
until it is completely folded.
K
D Do
oo
or
rs
s,
, cce
en
nt
tr
ra
al
l llo
oc
ck
ki
in
ng
g*
*
Locking and unlocking the vehicle
When the front doors are locked or unlocked, all the other doors,
the tank flap and the tailgate are locked or unlocked by the central
locking system.
The central locking system is equipped with an added security
mechanism: Once the vehicle has been locked from the outside,
the internal door locking levers can immediately be moved freely.
In other words they are disengaged from the outside handles. The
doors can no longer be opened from the inside. This makes
breaking in difficult.
The system may be activated from outside both with the key and
the radio-frequency remote control*.
The warning lamp on the driver’s door covering will begin to f fl
li
ic
ck
ke
er
r
to show that the security system is activated.
K
Unlocking
To unlock the vehicle, turn the key in a front door or the tailgate
lock to the open position.
N No
ot
te
e
When you open the vehicle the inside lights in door contact position will
come on for about 20 seconds.
If the central locking should fail, all locks – with the exception of the tank
flap – can be operated normally. (If the car was simply locked, simply turn
the key twice in the door locks). Tank flap emergency release
⇒page 158.
Fig. 61
A
LEO-006


Opening and closing76
Interior light control
The interior light is switched on for approx. 20 seconds when the
vehicle is unlocked, a door opened or the ignition key removed.
The switch must be in the door contact position for this function.
Once the door is closed, the inside light remains on for another 20
seconds (delayed switch off of inside light).
It is however switched off as soon as the vehicle is locked or the
ignition switched on, and whenever all the doors and boot/tailgate
are closed.
With the door open, the interior light will remain on for a maximum
of ten minutes. This prevents the vehicle battery from discharging.
Once the ignition is off, all inside lights, including reading light,
the one on the courtesy mirror and on the door, and the boot light,
will remain switched on for a maximum of one hour, to prevent the
battery from discharging.
N No
ot
te
e
On vehiclesw wi
it
th
ho
ou
ut
t
an anti-theft warning system*, the interior light isn no
ot
t
switched on when the tailgate is opened.K
Central locking button*
The central locking button makes it possible to lock/unlock the
whole vehicle from the inside. The button is located in the door
release lever on the driver’s door
⇒ fig. 63.
L Lo
oc
ck
ki
in
ng
g
By pressing the right hand side of the switch
Aall doors and the
boot lid/tailgate are locked. It is now no longer possible to open
the doors or boot lid/tailgate. Unwanted access from outside (e.g.
at trafficlights) is also prevented in this way.
If the driver’s door iso op
pe
en
n
it will not be locked. This is to prevent
you from locking yourself out.
The dead-lock mechanism and anti-theft alarm* are n no
ot
t
activated
when the button is operated.
Fig. 63
AB
AL0-002


Opening and closing81
Safety FirstControls and equipment Tips and Maintenance Technical Data
Volumetric sensor
This is a surveillance function or a control incorporated in the anti-
theft alarm system which detects through ultrasound unauthorized
access to the vehicle interior (i.e. through a window). This system
has two sensors: a transmitter and a receiver.
A Ac
ct
ti
iv
va
at
te
e
The volumetricsensor is switched on automatically when the anti-
theft alarm is activated whether by locking manually with the key
or by remote control.
D De
ea
ac
ct
ti
iv
va
at
te
e
The volumetricsensor is deactivated when unlocking the vehicle
manually with the key in the door lock or by radio wave remote
control.
N No
ot
te
e
• A warning lamp in the driver’s door will flash if the alarm has been
triggered by the volumetricsensor. This flashing is different from that of the
activated alarm.
• If the volumetricsensor has caused the alarm to set off three times the
alarm system will no longer go off.
• Other sensors (door opening, luggage compartment, etc.) will continue to
set off the alarm.
K
R Ra
ad
di
io
o-
-f
fr
re
eq
qu
ue
en
nc
cy
y rre
em
mo
ot
te
e cco
on
nt
tr
ro
ol
l kke
ey
y*
*
Locking and unlocking the vehicle
You can use the remote control to carry out the following
operations without having to use the key:
– Opening and closing the central locking.
– Switching the anti-theft alarm* and the safety locking system on
and off.
– Individual opening* of just the driver’s door.
– Connecting and diconnecting the inside light
⇒"Doors, central
locking" chapter.
The radio wave emitter with batteries is incorporated into the grip
of the car key. The receiver is in the cabin.

Fig. 67AL0-081

Opening and closing82
The e ef
ff
fe
ec
ct
ti
iv
ve
e rra
an
ng
ge
e
(red areas) of the remote control are shown in
the fig. 67. The maximum range depends on several factors.
The range is also reduced as the batteries wear down.
N No
ot
te
e
Duplicate, unprogrammed keys for the remote control are available at
Technical Service Centres. However, the second key must be synchronised
in a SEAT Official Service Centre, as the immobiliser code must also be
entered into the head of the key.
Up to a maximum of four keys with radio-frequency remote control maybe
used.
K
Opening and closing your vehicle
To open the car, point the key at the car, within the effective range,
and briefly press the opening button (arrow 1). To close the car,
briefly press the closing button (arrow 2).
If you press the closing button (arrow
2) twice, the safety lock and
anti-theft alarm system* are deactivated and the indicators will
briefly flash to show this.
N No
ot
te
e
While the “open” or “close” buttons are pressed, a warning lightin the key
flashes. If this does not happen, the battery in the key might be flat. In this
case a Technical Service Centre should check or change the battery.
When the safety lock and the anti-theft alarm* are activated,
proceed in the following manner:
If you open the car with the opening button of the radio-frequency*
remote control, all the locks will be blocked automatically if you do
not open any of the doors or boot/tailgate before 30 seconds have
elapsed. However, the safety lock and the anti-theft alarm* will be
deactivated during those 30 seconds. This function stops
u un
nw
wa
an
nt
te
ed
d oop
pe
en
ni
in
ng
g
of the vehicle within the effective range of the
radio-frequency* remote control.
When unlocking the vehicle, keep the key in the driver’s and
passenger’s door lock or tailgate in the unlocking position. All
windows, except for the lateral electric windows, will open
automatically.
When keeping the key in the locking position, the windows and the
roof will close automatically.
21
LEO-009Fig. 68

Opening and closing83
Safety FirstControls and equipment Tips and Maintenance Technical Data
Individual opening of the doors
O Op
pe
en
ni
in
ng
g wwi
it
th
h tth
he
e iin
nd
di
iv
vi
id
du
ua
al
l oop
pe
en
ni
in
ng
g aac
ct
ti
iv
va
at
te
ed
d
To o op
pe
en
n
the car, point the key at it within the effective range and
briefly press the opening button
⇒ fig. 68, arrow 1o
on
nc
ce
e
:
Only the driver’s door is unlocked. The safety lock and the anti-
theft alarm* are immediately deactivated, and all the indicators
flash to show this.
• If you press the opening button
⇒ fig. 68, arrow 1t
tw
wi
ic
ce
e
all the
locks are unlocked.
• The safety lock and the anti-theft alarm* remain deactivated.
N No
ot
te
e
All other individual door opening functions can be found in the "Doors,
central locking" chapter.K
Synchronisation
If the vehicle cannot be opened by pressing the radio transmitter
button, it could be that the code of the key no longer matches that
of the control unit in the vehicle. This can occur if the transmitter
button is frequently pressed outside the effective range of the
system.
The infrared key must be resynchronized. The synchronization
process must be completed with 1 1 mmi
in
nu
ut
te
e
.
The necessary steps for the programming of the key are:
1. Insert key into driver’s door lock and turn three times forwards
(unlock), before 5 seconds have elapsed (maximum). Each time
hold it for 1/2 second in the unlock position. Remove key. The
warning lamp in the inner driver’s door cover will flash to show that
the operation has been properly completed.
2. Press and hold “close” button
⇒ fig. 68, arrow 2.
3. Press “open” button
⇒ fig. 68, arrow 13 times. Release
“close” button. The key has now been recoded. To check the
system, the warning lamp in the door trim will flash, and the light
in the key will flash 5 times.
If any further infrared keys are being used, they must also be
synchronised. To do this, steps 2 to 4 of the synchronisation
procedure must be carried out. This procedure must not last any
longer than 15 seconds for each key and must be carried out
immediately after the synchronisation of the previous key.
T To
o een
ns
su
ur
re
e tth
ha
at
t nno
ob
bo
od
dy
y iis
s iin
nj
ju
ur
re
ed
d wwh
he
en
n ccl
lo
os
si
in
ng
g tth
he
e wwi
in
nd
do
ow
ws
s oor
r
s sl
li
id
di
in
ng
g/
/t
ti
il
lt
ti
in
ng
g rro
oo
of
f,
, tth
he
e oop
pe
er
ra
at
to
or
r ssh
ho
ou
ul
ld
d aal
lw
wa
ay
ys
s wwa
at
tc
ch
h tth
he
e wwi
in
nd
do
ow
ws
s aan
nd
d
s sl
li
id
di
in
ng
g/
/t
ti
il
lt
ti
in
ng
g rro
oo
of
f aas
s tth
he
ey
y ccl
lo
os
se
e.
.
C Ca
ar
re
el
le
es
ss
s oor
r uun
nc
co
on
nt
tr
ro
ol
ll
le
ed
d ccl
lo
os
si
in
ng
g oof
f tth
he
e wwi
in
nd
do
ow
ws
s cca
an
n cca
au
us
se
e iin
nj
ju
ur
ri
ie
es
s.
.
K
W WA
AR
RN
NI
IN
NG
G


Lights and visibility92
N
No
ot
te
e
• A warning lamp in the instrument panel lights up when the rear fog light is
switched on.
• Due to the amount of dazzle it causes, the rear fog light should only be
switched on when the visibility is very poor (e.g. in some E.U. countries, 50
metres).
The electrical system of the factory fitted tow bar* is wired up so
that when towing a trailer fitted with rear fog lights, the rear fog
light on the towing vehicle are automatically switched off.
K
Coming Home/Leaving Home function
After dark the area around the car is lit up with the aid of the
coming home / leaving home function.
T To
o aac
ct
ti
iv
va
at
te
e tth
he
e ffu
un
nc
ct
ti
io
on
n
This function can be activated, using the light switch, for 2 minutes
after the dipped headlights are switched off. This is done as
follows:
– Switch off the ignition with the doors closed.
– Move the indicator lever briefly in the direction of the steering
wheel (headlight flasher).
– Unlock the driver's door At his point the function is activated.
O Op
pe
er
ra
at
ti
io
on
n oof
f tth
he
e CCo
om
mi
in
ng
g HHo
om
me
e/
/L
Le
ea
av
vi
in
ng
g HHo
om
me
e ffu
un
nc
ct
ti
io
on
n
• When the driver’s door is opened, the dipped front headlights
will be switched on automatically for approximately 3 minutes.• If the driver’s door is closed during these 3 minutes, the dipped
headlights will remain lit for approximately 30 seconds.
• Switching on the vehicle ignition during the activation period will
switch off the dipped headlights.
K
Instrument lighting/Headlight range control*
I In
ns
st
tr
ru
um
me
en
nt
t lli
ig
gh
ht
ti
in
ng
g 2
When the lights are on, the level of the instrument lighting can be
set to any intensity by turning the knurled wheel next to the light
switch.
H He
ea
ad
dl
li
ig
gh
ht
t rra
an
ng
ge
e cco
on
nt
tr
ro
ol
l
3
With the electrical range control the headlight settings can be
matched exactly to the load condition of vehicle. This prevents
Fig. 76
123
AL0-018


Lights and visibility93
Safety FirstControls and equipment Tips and Maintenance Technical Data
oncoming traffic from being dazzled more than is unavoidable. At
the same time the correct headlight beam setting provides the
best possible visibility for the driver.
The headlights can only be regulated with the dipped headlights
switched on.
To lower the beams, turn knurled discfrom the basicposition (–)
downwards.
K
S Sw
wi
it
tc
ch
he
es
s iin
n tth
he
e cce
en
nt
tr
ra
al
l cco
on
ns
so
ol
le
e
Rear window heating 1
The heating will only function when the ignition is turned on.
On vehiclesw wi
it
th
ho
ou
ut
t wwi
in
nd
ds
sc
cr
re
ee
en
n hhe
ea
at
ti
in
ng
g
*, the heating is turned
on/off using this switch. A warning lamp will light up in the switch
when the heating is on.
On vehicles with electrically adjustable exterior mirrors the mirrors
are heated as long as the rear window heating is switched on.
On vehiclesw wi
it
th
h wwi
in
nd
ds
sc
cr
re
ee
en
n hhe
ea
at
ti
in
ng
g
, the heating is switched on
with a button.
The rear window heating automatically switches off about 20
minutes after it is switched on. It can also be switched off earlier by
pressing the button again.
If the heating is still required, simply press the button again. It will
again be switched off automatically after a further 20 minutes.
On vehicles with electrically adjustable exterior mirrors the mirrors
are heated as long as the rear window heating is switched on.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
As soon as window is clear, switch element off. The reduced current
consumption helps to reduce fuel consumption ⇒"Economic and
environment friendly driving" chapter.K
Fig. 77
1
2
3
4
5
6
7
8
ESP2PDC
1
AL0-087

Lights and visibility94
Windscreen heating*2
The windscreen heating works only when the engine is running.
When it is on a warning lamp in the switch lights up.
The windscreen heating automatically switches off about 10
minutes after it is switched on. It can also be switched off earlier by
pressing the button again.
If the heating is still required, press the switch again. The switch
will again switch off after about 10 minutes.
N No
ot
te
e
For technical reasons, the blower of the passenger compartment heater is
switched off when the windscreen heating is switched on.K
Knurled wheel for seat heating*3/7
The cushion and backrest of the front seats can be heated
electrically when the ignition is on.
The heating is switched on and regulated with the knurled wheel.
To switch heating off, turn knurled wheel to the basic position (0).
K
Anti-skidding system of the drive wheels (TCS).
Electronic Stability Program (ESP)* 4
The TCS or ESP connect automatically when the engine is switched
on. If necessary, they may be switched off briefly by pressing
corresponding switch.
If it is connected a warning lamp will light
⇒"Warning lamps"
chapter.
For further information
⇒pages 164 to 166.K
Hazard warning lamps5
The system also works when the ignition is switched off.
Switch on the hazard warning lamps if, for example:
– Your vehicle stops because of a technical defect,
– You have an emergency
– You reach the tail end of a traffic jam.
Fig. 78
1
2
3
4
5
6
7
8
ESP2PDC
1
AL0-087