Page 114 of 282

114
Controls, Instruments
Automatic Headlight Beam
Adjustment Vehicles with Bi-Xenon headlights feature
automatic headlight beam adjustment.
When the ignition is switched on, the level of the
headlight beam automatically changes in accord-
ance with the vehicle load.
The level of the headlight beam is automatically
kept constant during acceleration and braking. Checking operation 1. Switch the low beam on.
2. Insert ignition key and switch ignition on.
The light beam first dips all the way down and
is then adapted to the vehicle load.
If this test item is not met, the headlight beam
adjustment system must be checked by an author-
ized Porsche dealer.
Turn Signal / Headlight Dimmer /
Parking light / Flasher Lever Turn signals, low beam and high beam are ready
for operation when the ignition is on.
1 – Turn signal left
2 – Turn signal right
Push the lever to the upper or lower pressure
point – turn signals flash three times
3 – High beam
4 – Headlight flasher
Lever in center position – Low beam
When high beam and headlight flasher are select-
ed, the blue indicator light in the tachometer is lit. The turn signal lever turns off automatically when
the steering wheel is straightened out after com-
pleting a turn.
Lane changer fTo indicate your intention when changing lanes
on the freeway, slightly lift or depress the lever
to the resistance point.
The lever will return to the OFF position when
released.
fIf the frequency of the display becomes notice-
able faster, check the operation of the turn sig-
nal bulbs. Headlight flasher (With ignition on or off)
fTo flash the headlights to oncomming motor-
ists, slightly pull the lever toward the steering
wheel and then release it.
The blue indicator light in the tachometer will
go on/off as you pull/release the lever. Parking lightThe parking light can only be switched on when
the ignition is switched off.
fMove the lever up or down to switch on the
right or left parking light.
Page 245 of 282
Practical Tips, Emergency Service
245
Bulb chart
Ty p e , r a t i n g
Halogen low beam H7, 55W
Low beam with Bi-Xenon headlight Philips, D2S 35W
Halogen high beam H9, 65W
Additional high beam with Bi-Xenon headlight H11, 55W
Fog light H8, 35W
Tail light, rear fog light P21/4W
Brake light/tail light P21/4W
Tail light, reflector P21/5W
Make-up mirror light K3W
Reversing light P21
Trun signal indicator light, front and rear PY21W
Turn signal indicator light, side WY5W
Side marker light W3W
Door guard/Curb light W5W
Parking light W5W Blue-Vision
License plate light C5W
Luggage compartment/engine compartment
light, interior lightK10W
Reading light 6W Xenon
Page 250 of 282
250
Practical Tips, Emergency Service
Changing bulbs for parking light, turn
signal light and fog lightThe release card for the auxiliary headlights is
inside the vehicle folder.
1. Insert release card at the side of the auxiliary
headlight.
The auxiliary headlight is released by pushing
in the card.
The card may have to be pushed again to
release the second connection.2. Remove auxiliary headlight.
Ensure that the vent hose D is not lost when
the auxiliary headlight is pulled out.
A - Parking light
B - Turn signal
C - Fog light
D - Vent hose
Page 251 of 282
Practical Tips, Emergency Service
251
Bulb for parking light A
1. Turn holder towards the left and pull it out to
the rear.
2. Pull out and replace defective bulb.
3. Push holder back in and turn towards the right.Bulb for turn signal B
1. Turn holder counter-clockwise (bayonet lock)
and remove it.
2. Turn the defective bulb counter-clockwise
(bayonet lock) and replace it.
3. Insert holder and turn towards the right.Bulb for fog light C
1. Press the release tab of the plug and pull plug
off.
2. Turn bulb of the defective left fog light towards
the left and the bulb of the right fog light
towards the right (bayonet lock) and replace
them.
3. Push on plug.
Page 253 of 282
Practical Tips, Emergency Service
253
Changing bulb for side marker light1. Remove the cap in the wheel housing liner with
a screwdriver.
2. Insert the screwdriver into the opening in the
wheel housing liner at right angles to the turn
signal housing.
By pressing with the screwdriver, disengage
the securing spring of the turn signal housing.3. Swivel out the indicator light and undo bulb
holder (bayonet lock).
4. Remove the bulb from the holder and replace
it. Insert holder.
Check operation of the light.
5. Insert the turn signal’s retaining lugs A into the
side section at the front.
Push in turn signal until the securing spring B
is felt to engage.
6. Press the cap into the wheel housing liner.
Page 254 of 282
254
Practical Tips, Emergency Service
Tail LightChanging bulb1. Open the engine compartment lid.
2. Completely unscrew fastening screw A.
3. Pull tail light out towards the back.
A- Reversing light
B-Turn signal
C- Tail light/brake light
D- Tail light/reflector
E- Rear fog light/side marker light4. Turn the bulb holder in the tail light housing
counter-clockwise and pull it out.
5. Turn the defective bulb counter-clockwise
(bayonet lock) and replace it.
6. Insert the bulb holder and turn it clockwise.7. Insert tail light into the side section.
Ensure that the retaining lug has been inserted
into the mounting guide properly.
8. Tighten fastening screw A on the tail light.
9. Check operation of the light.