2005 MITSUBISHI LANCER service

KEYLESS ENTRY SYSTEM
BODY42-53
TROUBLESHOOTINGM1428000700287
The keyless entry system is controlled by the Smart
Wiring System (SWS). For troubleshooting, refer to
GROUP 54B, Troubleshooting P.54B-17 or GROUP
54C, Troubleshooting P.54C-4.
ON-VEHICLE SERVICE
KEYLESS ENTRY SYSTEM CHECKM1428001400096
Check the system as described below. If the system
does not work, carry out troubleshooting. Refer to
GROUP 54B, Troubleshooting P.54B-17, refer to
GROUP 54C, Troubleshooting P.54C-4.
•Operate the transmitter to check that the doors
and tailgate can be locked and unlocked.
•Operate the transmitter to check that the
answerback function works in response to door
and tailgate locking/unlocking.
NOTE: The adjustment function allows you to
change the answerback setting as follows. Prior
to that check, confirm which setting is activated.
.
•The hazard warning lamps flash twice when
locked and once when unlocked. The room
lamp flashes twice when locked and
illuminates for 15 seconds when unlocked.
•The hazard warning lamps do not flash when
locked and flash once when unlocked. The
room lamp flashes twice when locked and
illuminates for 15 seconds when unlocked.
•The hazard warning lamps flash twice when
locked and do not flash when unlocked. The
room lamp flashes twice when locked and
illuminates for 15 seconds when unlocked.
•The hazard warning lamps do not flash when
both locked and unlocked. The room lamp
flashes twice when locked and illuminates for
15 seconds when unlocked.
KEYLESS ENTRY SYSTEM TIMER LOCK
FUNCTION INSPECTION
M1428004000138
Push the transmitter unlock button and check to see
that the doors and tailgate lock within 30
seconds. If it doesn't, then execute troubleshooting
remedies. Refer to GROUP 54B, Troubleshooting
P.54B-17, refer to GROUP 54C, Troubleshooting
P.54C-4.
ENABLING/DISABLING THE
ANSWERBACK FUNCTION
M1428003200214
If the keyless entry system locks or unlocks the
doors, the room lamp flashes or illuminates, the
hazard warning lamp flashes (hazard answerback
function). The hazard answerback function can be
enabled or disabled according to the following
procedure:
ENABLING/DISABLING THE HAZARD
ANSWERBACK FUNCTION
The hazard answerback function can be enabled or
disabled by one of the two following procedures.
diagnosis connector (1) is earthed>
1. Enter the hazard answerback customize mode by
performing one of the following steps. If the
ETACS-ECU enters the customize mode, its
buzzer will sound once.
(1) Turn the ignition switch to “LOCK”(OFF)
position.
(2) Turn off the hazard warning lamp switch.
CAUTION
Before connecting or disconnecting the earth,
turn the ignition switch to the "LOCK" (OFF)
position.
(3) Connect the diagnosis connector to the
special tool diagnosis code check harness
(MB991529).
(4) Close the driver's side door.
(5) Keep the windshield washer switch on for at
least ten seconds. Then the ETACS-ECU
buzzer will sound once.
2. If the transmitter “LOCK” button is pushed
consecutively twice (within two seconds), the
ETACS-ECU buzzer will sound, indicating that the
hazard answerback function can be enabled or
disabled when the doors are locked.
AC305133AB
Diagnosis
connector
MB991529Steering shaft

KEYLESS ENTRY SYSTEM
BODY42-59
DISASSEMBLY SERVICE POINT
<> BATTERY REMOVAL
CAUTION
Do not allow water or dust to enter the inside of
the transmitter assembly when it is open. Also,
do not touch the precision electronic device.
REASSEMBLY SERVICE POINT
>>A<< BATTERY INSTALLATION
CAUTION
Do not allow water or dust to enter the inside of
the transmitter assembly when it is open. Also,
do not touch the precision electronic device.Install a new battery to the transmitter assembly with
its (+) side facing towards the upper cover side.
Battery required for replacement: Coin type
battery CR1616
INSPECTIONM1428003800067
TRANSMITTER BATTERY CHECK
Measure the voltage of the battery. If the voltage of
the battery is not within the standard value, replace
the battery.
Standard value: 2.5 − 3.2 V
AC304118
AD
+ –
Master key sideUpper cover side
Battery Transmitter assembly
AC004486

51-1
GROUP 51
EXTERIOR
CONTENTS
FRONT BUMPER ASSEMBLY . . . . .51-2
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-2
FRONT BUMPER ASSEMBLY . . . . . . . . . . 51-2
REMOVAL AND INSTALLATION . . . . . . . . 51-2
DISASSEMBLY AND REASSEMBLY . . . . . 51-3
REAR BUMPER ASSEMBLY . . . . . .51-5
REMOVAL AND INSTALLATION . . . . . . . . 51-5
DISASSEMBLY AND REASSEMBLY . . . . . 51-7
MOULDINGS . . . . . . . . . . . . . . . . . . .51-9
SPECIAL TOOL . . . . . . . . . . . . . . . . . . . . . 51-9
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-9
MOULDINGS . . . . . . . . . . . . . . . . . . . . . . . 51-10
REMOVAL AND INSTALLATION . . . . . . . . 51-10
SIDE AIR DAM . . . . . . . . . . . . . . . . . .51-15
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . 51-15
SIDE AIR DAM . . . . . . . . . . . . . . . . . . . . . . 51-15
REMOVAL AND INSTALLATION . . . . . . . . 51-15
GARNISHES . . . . . . . . . . . . . . . . . . .51-17
REMOVAL AND INSTALLATION . . . . . . . . 51-17
REAR SPOILER . . . . . . . . . . . . . . . . .51-18
REMOVAL AND INSTALLATION . . . . . . . . 51-18
TAILGATE SPOILER . . . . . . . . . . . . .51-19
REMOVAL AND INSTALLATION . . . . . . . . 51-19
ROOF RAIL . . . . . . . . . . . . . . . . . . . .51-20
REMOVAL AND INSTALLATION . . . . . . . . 51-20
WINDSHIELD WIPER AND WASHER51-21
GENERAL INFORMATION . . . . . . . . . . . . . 51-21
SERVICE SPECIFICATION . . . . . . . . . . . . 51-22TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-22
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . 51-22
WINDSHIELD WIPER AND WASHER . . . . 51-23
REMOVAL AND INSTALLATION . . . . . . . . 51-23
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-25
REAR WIPER AND WASHER . . . . . .51-28
GENERAL INFORMATION . . . . . . . . . . . . . 51-28
SERVICE SPECIFICATION . . . . . . . . . . . . 51-28
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-28
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . 51-28
REAR WIPER AND WASHER . . . . . . . . . . 51-29
REMOVAL AND INSTALLATION . . . . . . . . 51-29
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-30
HEADLAMP WASHER . . . . . . . . . . . .51-32
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-32
HEADLAMP WASHER . . . . . . . . . . . . . . . . 51-32
REMOVAL AND INSTALLATION . . . . . . . . 51-32
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-33
MARK . . . . . . . . . . . . . . . . . . . . . . . . .51-34
REMOVAL AND INSTALLATION . . . . . . . . 51-34
DOOR MIRROR . . . . . . . . . . . . . . . . .51-36
GENERAL INFORMATION . . . . . . . . . . . . . 51-36
SERVICE SPECIFICATION . . . . . . . . . . . . 51-36
SPECIAL TOOL. . . . . . . . . . . . . . . . . . . . . . 51-36
TROUBLESHOOTING . . . . . . . . . . . . . . . . 51-36
DIAGNOSIS TROUBLESHOOTING
FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-36
TROUBLE SYMPTOM CHART . . . . . . . . . . 51-36
SYMPTOM PROCEDURES . . . . . . . . . . . . 51-37
DOOR MIRROR . . . . . . . . . . . . . . . . . . . . . 51-45
REMOVAL AND INSTALLATION . . . . . . . . 51-45
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . 51-47

FRONT BUMPER ASSEMBLY
EXTERIOR51-4
DISASSEMBLY SERVICE POINT
<> FRONT BUMPER SIDE PLATE
ASSEMBLY REMOVAL
Use a drill (4.0 mm) to make a hole in the rivet to
break it, and then remove the rivet.
REASSEMBLY SERVICE POINT
>>A<< FRONT BUMPER SIDE PLATE
ASSEMBLY
Use the rivet tool shown in the illustration to attach
the rivet by the following procedure.
1. Insert the rivet into the base material front bumper
side plate assembly.
2. Place the recommended tool over section A of the
rivet.
3. While pushing the flange surface of the rivet with
the recommended tool, press the handle of the
tool.
4. The thin part of section A of the rivet will break
and the rivet will then be attached.
AC100411AB
Rivet Drill
Bumper face
AC305178AB
1
2
3
4Section A
Rivet
Rivet tool
Flange
Rivet Front bumper
side plateRivet tool
Front bumper
face
Front bumper face

REAR BUMPER ASSEMBLY
EXTERIOR51-8
DISASSEMBLY SERVICE POINT
<> RIVET REMOVAL
Use a drill (4.0 mm) to make a hole in the rivet to
break it, and then remove the rivet.
ASSEMBLY SERVICE POINT
>>A<< RIVET INSTALLATION
Use the rivet tool shown in the illustration to attach
the rivet by the following procedure.
1. Insert the rivet into the rear bumper face and rear
bumper side plate.
2. Insert “A” of the rivet into the rivet tool.
3. Pressing the flange surface of the rivet, move the
handle of the rivet tool.
4. The thinnest point of “A” is cut and the rivet is held
in position.
AC100411AB
Rivet Drill
Bumper face
Y0412AU
AC00587618E0192AB
1
2
3
4Section A
Rivet
Flange
Rivet Rear bumper
side plateRear bumper
face
Rear bumper face
Recommended tool
Recommended
tool

MOULDINGS
EXTERIOR51-11
REMOVAL SERVICE POINT
<> ROOF DRIP MOULDING REMOVAL
CAUTION
If the moulding has become warped, it should not
be reused.
Use special tool window moulding remover
(MB990449) to lever out the moulding.
AC304340
1
1
A
A
A
A
AB
B
B
C
C
C
C
B
B
N
N
N
2
N2
4
3
N3
N4
N
6
9
7
N
6N
N
7N
N9


Removal
•Front deck garnishes (Refer to
P.51-23.)
Roof drip moulding removal steps
<> >>C<<1. Roof drip moulding
>>B<<2. Front drip moulding clip A
>>B<<3. Front drip moulding clip B
>>B<<4. Front drip moulding clip C
>>B<<5. Rear drip moulding clip
>>A<<6. Drip moulding clip A
>>A<<7. Drip moulding clip B
>>A<<8. Drip moulding clip C
9. Roof drip moulding clip Roof drip moulding removal steps
AC304375MB990449AB

MOULDINGS
EXTERIOR51-12
INSTALLATION SERVICE POINTS
>>A<< DRIP MOULDING CLIP C/DRIP
MOULDING CLIP B/DRIP MOULDING
CLIP A INSTALLATION
1. The drip moulding clips A, B and C differ
according to where they are used, so check the
identification colour before installation.
2. After installing the clip to the front pillar outer in
alignment with its section A, cut from section B.
>>B<< REAR DRIP MOULDING
CLIP/FRONT DRIP MOULDING CLIP
C/FRONT DRIP MOULDING CLIP
B/FRONT DRIP MOULDING CLIP A
INSTALLATION
The front drip moulding clips A, B, C and rear drip
moulding clip differ according to where they are
used, so check the identification colour before
installation.
>>C<< ROOF DRIP MOULDING
INSTALLATION
Install the clips to the roof drip moulding before
installing the moulding to the vehicle body. Applicable location Identification colour
Drip moulding clip A Yellow
Drip moulding clip B Blue
Drip moulding clip C Milky white
AC304374
Front pillar outer
Section B
Section A
AB
Applicable location Identification colour
Front drip moulding clip A Orange
Front drip moulding clip B Purple
Front drip moulding clip C Blue
Rear drip moulding clip Grey

MOULDINGS
EXTERIOR51-14
REMOVAL SERVICE POINT
<> FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS REMOVAL
Gently lift and remove the door moulding. If there is
any double-sided tape remaining on the door
moulding, remove according to the following
instructions.
surface>
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
2. Use a resin spatula to scrape off the double-sided
tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with isopropyl alcohol.
moulding and adhere double-sided tape (when
re-using door moulding)>1. Scrape off the double-sided tape on the door
moulding with a resin spatula as possible.
2. Wipe the door moulding surface and clean it with
a rag moistened with isopropyl alcohol.
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
door moulding.
INSTALLATION SERVICE POINT
>>A<< FRONT FENDER, FRONT AND
REAR DOOR MOULDINGS
INSTALLATION
1. Tear off the double-sided tape backing paper.
NOTE: If attach the adhesive tape to the edge of
the backing paper, it will be easy to tear off.
2. Install the clips to the front and rear door
mouldings before installing them to the vehicle
body.
3. Install the door mouldings.
NOTE: . If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding
surfaces of the body and door mouldings to about
40
− 60°C before affixing the tape.
4. Firmly press in the door mouldings onto the
respective body surfaces.
AC000420Double-sided tapeProtection tapeAB
AC000421
Double-sided tape
AB
AC313343
AC313344
Backing paper Adhesive tape
AB