2005 MERCEDES-BENZ SPRINTER tire pressure

(12) Disconnect the discharge line from the retain-
ing clip and remove the discharge line from the vehi-
cle.
INSTALLATION
Any kinks or sharp bends in the refrigerant plumb-
ing will reduce the capacity of the entire air condi-
tioning system. Kinks and sharp bends reduce the
flow of refrigerant in the system. A good rule for the
flexible hose refrigerant lines is to keep the radius of
all bends at least ten times the diameter of the hose.
In addition, the flexible hose refrigerant lines should
be routed so they are at least 80 millimeters (3
inches) from the exhaust manifold.
(1) Position the discharge line into the engine com-
partment.
(2) Remove the tape or plugs from the compressor
discharge port and the discharge line fitting.
(3) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the discharge line fit-
ting.
(4) Connect the discharge line fitting to the com-
pressor discharge port on the top of the compressor.(5) Install the bolt that secures the discharge line
fitting to the compressor. Tighten the bolt to 23 N´m
(17 ft. lbs.).
(6) Remove the tape or plugs from the condenser
inlet port and the discharge line fitting.
(7) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the discharge line fit-
ting.
(8) Connect the discharge line fitting to the con-
denser inlet port.
(9) Install the nut that secures the discharge line
fitting to the condenser. Tighten the nut to 33 N´m
(24 ft. lbs.).
(10) Install the grille(Refer to 23 - BODY/EXTERI-
OR/GRILLE - INSTALLATION).
(11) Evacuate the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM EVACUATE)
(12) Charge the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM CHARGE)
(13) Reconnect the negative battery cable.
A/C EVAPORATOR
DESCRIPTION
The evaporator is located in the heater housing,
behind the instrument panel. The evaporator is posi-
tioned in the housing so that all air that enters the
housing must pass over the fins of the evaporator
coils before it is distributed through the system ducts
and outlets. However, air passing over the evaporator
coil fins will only be conditioned when the compres-
sor is engaged and refrigerant is circulating through
the evaporator coil tubes.
OPERATION
Refrigerant enters the evaporator from the expan-
sion valve as a low-temperature, low-pressure liquid.
As air flows over the fins of the evaporator, the
humidity in the air condenses on the fins, and the
heat from the air is absorbed by the refrigerant. Heat
absorption causes the refrigerant to boil and vapor-
ize. The refrigerant becomes a low-pressure gas
before it leaves the evaporator.
The evaporator cannot be repaired and, if faulty or
damaged, it must be replaced.
Fig. 4 A/C Compressor - Refrigerant Lines
1 - A/C COMPRESSOR
2 - O-RING SEAL
3 - SUCTION LINE
4 - BOLT
5 - RETAINING CLIP
6 - BOLT
7 - DISCHARGE LINE
8 - O-RING SEAL
24 - 54 PLUMBINGVA
A/C DISCHARGE LINE (Continued)

BACKLITE - BULKHEAD TRIM PANEL -
INSTALLATION.......................23-81
BACKLITE - BULKHEAD TRIM PANEL -
REMOVAL..........................23-81
BACKUP LAMP BULB - INSTALLATION.....8L-6
BACKUP LAMP BULB - REMOVAL........8L-5
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-3
BALL JOINT - INSTALLATION, LOWER......2-6
BALL JOINT - REMOVAL, LOWER..........2-6
BAR - DESCRIPTION, STABILIZER.........2-9
BAR - INSTALLATION, STABILIZER.....2-15,2-9
BAR - OPERATION, STABILIZER...........2-9
BAR - REMOVAL, STABILIZER........2-15,2-9
BASE BRAKE, SPECIFICATIONS............5-6
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-2
BASECOAT/CLEARCOAT FINISH -
DESCRIPTION.......................23-74
BATTERY - DESCRIPTION...............8F-6
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY - OPERATION.................8F-7
BATTERY CABLES - DESCRIPTION.......8F-14
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-14
BATTERY CABLES - INSTALLATION.......8F-16
BATTERY CABLES - OPERATION.........8F-14
BATTERY CABLES - REMOVAL..........8F-16
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY ELECTROLYTE LEVEL -
STANDARD PROCEDURE, CHECKING.....8F-12
BATTERY HOLDDOWN - DESCRIPTION....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-14
BATTERY HOLDDOWN - REMOVAL.......8F-14
BATTERY INSTALLATION, INSTALLATION
- AUXILIARY........................8F-13
BATTERY INSTALLATION, INSTALLATION
- UNDER HOOD......................8F-13
BATTERY REMOVAL, REMOVAL -
AUXILIARY..........................8F-13
BATTERY REMOVAL, REMOVAL - UNDER
HOOD..............................8F-12
BATTERY SYSTEM - CLEANING...........8F-5
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION.........8F-2
BATTERY SYSTEM SPECIAL TOOLS,
SPECIAL TOOLS......................8F-6
BATTERY TESTER - STANDARD
PROCEDURE, USING MICRO 420........8F-11
BATTERY TRAY - DESCRIPTION.........8F-16
BATTERY TRAY - INSTALLATION.........8F-16
BATTERY TRAY - OPERATION...........8F-16
BATTERY TRAY - REMOVAL............8F-16
BEAM HEADLAMP BULB -
INSTALLATION, HIGH.................8L-17
BEAM HEADLAMP BULB -
INSTALLATION, LOW..................8L-19
BEAM HEADLAMP BULB - REMOVAL,
HIGH..............................8L-17
BEAM HEADLAMP BULB - REMOVAL,
LOW ..............................8L-18
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-17
BEAM INDICATOR - OPERATION, HIGH....8J-17
BEARING - INSTALLATION, CENTER........3-9
BEARING - INSTALLATION, HUB...........2-5
BEARING - INSTALLATION, OUTPUT
SHAFT............................21-122
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, HUB..............2-4
BEARING - REMOVAL, OUTPUT SHAFT . . . 21-122
BEARINGS/SEALS - INSTALLATION, AXLE . . 3-17
BEARINGS/SEALS - INSTALLATION, AXLE
HUB................................3-20
BEARINGS/SEALS - REMOVAL, AXLE......3-17
BEARINGS/SEALS - REMOVAL, AXLE
HUB
................................3-20
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE
.....................7-5
BELT & RETRACTOR - INSTALLATION,
FRONT SEAT
........................8O-21
BELT & RETRACTOR - INSTALLATION,
REAR SEAT
.........................8O-29
BELT & RETRACTOR - REMOVAL, FRONT
SEAT
..............................8O-19BELT & RETRACTOR - REMOVAL, REAR
SEAT ..............................8O-27
BELT BUCKLE - INSTALLATION, FRONT
SEAT ..............................8O-23
BELT BUCKLE - REMOVAL, FRONT SEAT . . 8O-22
BELT SWITCH - DESCRIPTION, SEAT.....8O-31
BELT SWITCH - OPERATION, SEAT.......8O-31
BELT TENSIONER - DESCRIPTION, SEAT . . 8O-31
BELT TENSIONER - OPERATION, SEAT....8O-32
BELT TENSIONERS - DESCRIPTION........7-5
BELT TENSIONERS - OPERATION..........7-5
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-34
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-33
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR INNER..................23-87
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR OUTER.................23-87
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR INNER..................23-87
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR OUTER.................23-87
BELTS - INSTALLATION, DRIVE............7-8
BELTS - REMOVAL, DRIVE...............7-8
BEZEL - INSTALLATION, ACCESSORY
SWITCH............................23-54
BEZEL - INSTALLATION, CLUSTER.......23-54
BEZEL - INSTALLATION, INSTRUMENT
PANEL CENTER......................23-55
BEZEL - REMOVAL, ACCESSORY SWITCH . 23-54
BEZEL - REMOVAL, CLUSTER...........23-53
BEZEL - REMOVAL, INSTRUMENT PANEL
CENTER............................23-55
BLADE - DESCRIPTION, WIPER.........8R-15
BLADE - INSTALLATION, WIPER.........8R-16
BLADE - OPERATION, WIPER...........8R-15
BLADE - REMOVAL, WIPER............8R-16
BLEED PROCEDURE, STANDARD
PROCEDURE - POWER STEERING
PUMP FILL.........................19-14
BLEEDING - STANDARD PROCEDURE,
MANUAL.............................5-4
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...................5-17
BLEEDING - STANDARD PROCEDURE,
PRESSURE...........................5-5
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR...................24-16
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-16
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-17
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-16
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-16
BLOCK #1 - DESCRIPTION, FUSE......8W-97-2
BLOCK #1 - INSTALLATION, FUSE.....8W-97-3
BLOCK #1 - OPERATION, FUSE.......8W-97-2
BLOCK #1 - REMOVAL, FUSE.........8W-97-3
BLOCK #2 - DESCRIPTION, FUSE......8W-97-3
BLOCK #2 - OPERATION, FUSE.......8W-97-3
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-14
BLOCK HEATER - REMOVAL, ENGINE......7-14
BLOCK JOURNALS - STANDARD
PROCEDURE, MEASURE CRANKSHAFT
....9-35
BLOWER MOTOR - INSTALLATION
. . 24-33,24-40
BLOWER MOTOR - REMOVAL
......24-32,24-39
BLOWER MOTOR RELAY - DESCRIPTION
. . 24-23
BLOWER MOTOR RELAY - DIAGNOSIS
AND TESTING
.......................24-24
BLOWER MOTOR RELAY -
INSTALLATION
.......................24-24
BLOWER MOTOR RELAY - OPERATION
. . . 24-23
BLOWER MOTOR RELAY - REMOVAL
.....24-24
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION
.......................24-16
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING
.............24-16
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION
.......................24-17
BLOWER MOTOR RESISTOR BLOCK -
OPERATION
.........................24-16
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL
..........................24-16BLOWER MOTOR SWITCH -
DESCRIPTION..................24-17,24-22
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING..................24-17,24-23
BLOWER MOTOR SWITCH -
INSTALLATION.......................24-23
BLOWER MOTOR SWITCH - OPERATION . . 24-17,
24-22
BLOWER MOTOR SWITCH - REMOVAL . . . 24-17,
24-23
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-1
BODY & CABLE - REMOVAL, ANTENNA....8A-1
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC.................23-3
BOLT INSPECTION - STANDARD
PROCEDURE, CYLINDER HEAD...........9-21
BOOST PRESSURE SENSOR -
DESCRIPTION.......................14-17
BOOST PRESSURE SENSOR -
DIAGNOSIS AND TESTING.............14-18
BOOST PRESSURE SENSOR -
INSTALLATION.......................14-18
BOOST PRESSURE SENSOR -
OPERATION.........................14-18
BOOST PRESSURE SENSOR - REMOVAL . . 14-18
BOOSTER - DESCRIPTION, POWER
BRAKE..............................5-19
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-16
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-19
BOOSTER - OPERATION, POWER BRAKE....5-19
BOOSTER - REMOVAL, POWER BRAKE....5-19
BORES - STANDARD PROCEDURE,
MEASURING CYLINDER................9-34
BOX - INSTALLATION, GLOVE...........23-56
BOX - REMOVAL, GLOVE..............23-56
B-PILLAR TRIM - INSTALLATION........23-69
B-PILLAR TRIM - REMOVAL............23-68
BRACKET - INSTALLATION, LICENSE
PLATE .............................23-47
BRACKET - INSTALLATION, PASSENGER
AIRBAG............................8O-27
BRACKET - INSTALLATION, REAR VIEW
MIRROR SUPPORT...................23-72
BRACKET - REMOVAL, LICENSE PLATE . . . 23-47
BRACKET - REMOVAL, PASSENGER
AIRBAG............................8O-27
BRAKE - CLEANING, REAR DRUM IN
HAT ................................5-27
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - REMOVAL, CONTROLLER
ANTILOCK...........................8E-3
BRAKE BOOSTER - DESCRIPTION,
POWER.............................5-19
BRAKE BOOSTER - INSTALLATION,
POWER.............................5-19
BRAKE BOOSTER - OPERATION, POWER . . . 5-19
BRAKE BOOSTER - REMOVAL, POWER....5-19
BRAKE CABLES - ADJUSTMENT,
PARKING............................5-25
BRAKE FLUID - DESCRIPTION............0-3
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-14
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-14
BRAKE FLUID, SPECIFICATIONS..........5-14
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-11
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-12
BRAKE LAMP SWITCH - INSTALLATION....8L-6
BRAKE LAMP SWITCH - REMOVAL.......8L-6
BRAKE, SPECIAL TOOLS - PARK.........5-23
BRAKE, SPECIFICATIONS - BASE..........5-6
BRAKE SWITCH - INSTALLATION, PARK . . . 8L-20
BRAKE SWITCH - REMOVAL, PARK
......8L-20
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE
........................5-2
BRAKE WEAR INDICATOR -
DESCRIPTION
.......................8J-12
BRAKE WEAR INDICATOR - OPERATION
. . . 8J-12
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION
.......................8J-11
2 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-12
BRAKE/PARK LAMP BULB -
INSTALLATION........................8L-7
BRAKE/PARK LAMP BULB - REMOVAL.....8L-7
BRAKES, SPECIAL TOOLS................5-7
BREAKER - DESCRIPTION, CIRCUIT....8W-97-2
BREAKER - DIAGNOSIS AND TESTING,
CIRCUIT.........................8W-97-2
BREAKER - OPERATION, CIRCUIT.....8W-97-2
BREAK-IN - STANDARD PROCEDURE,
COMPRESSOR CLUTCH................24-9
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-23
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-22
BULB - INSTALLATION, BACKUP LAMP....8L-6
BULB - INSTALLATION, BRAKE/PARK
LAMP...............................8L-7
BULB - INSTALLATION, CARGO/DOME
LAMP..............................8L-27
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
BULB - INSTALLATION, CLEARANCE
LAMP...............................8L-8
BULB - INSTALLATION, DOME
LAMP/INTRUSION SENSOR.............8L-30
BULB - INSTALLATION, DOME/READING
LAMP..............................8L-29
BULB - INSTALLATION, ENTRY/EXIT
LAMP..............................8L-32
BULB - INSTALLATION, FOG LAMP.......8L-10
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-14
BULB - INSTALLATION, FRONT
TURN/PARK/SIDE MARKER LAMP.......8L-15
BULB - INSTALLATION, HIGH BEAM
HEADLAMP.........................8L-17
BULB - INSTALLATION, LICENSE PLATE
LAMP..............................8L-18
BULB - INSTALLATION, LOW BEAM
HEADLAMP.........................8L-19
BULB - INSTALLATION, REAR SIDE
MARKER LAMP......................8L-21
BULB - INSTALLATION, REAR TURN
LAMP..............................8L-22
BULB - INSTALLATION, REPEATER LAMP . . 8L-22
BULB - REMOVAL, BACKUP LAMP........8L-5
BULB - REMOVAL, BRAKE/PARK LAMP....8L-7
BULB - REMOVAL, CARGO/DOME LAMP . . 8L-27
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
BULB - REMOVAL, CLEARANCE LAMP.....8L-8
BULB - REMOVAL, DOME LAMP/
INTRUSION SENSOR..................8L-30
BULB - REMOVAL, DOME/READING
LAMP..............................8L-29
BULB - REMOVAL, ENTRY/EXIT LAMP....8L-31
BULB - REMOVAL, FOG LAMP..........8L-10
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-14
BULB - REMOVAL, FRONT TURN/PARK/
SIDE MARKER LAMP.................8L-14
BULB - REMOVAL, HIGH BEAM
HEADLAMP.........................8L-17
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-17
BULB - REMOVAL, LOW BEAM
HEADLAMP.........................8L-18
BULB - REMOVAL, REAR SIDE MARKER
LAMP..............................8L-21
BULB - REMOVAL, REAR TURN LAMP....8L-21
BULB - REMOVAL, REPEATER LAMP.....8L-22
BULKHEAD - INSTALLATION............8L-29
BULKHEAD - REMOVAL................8L-28
BULKHEAD TRIM PANEL -
INSTALLATION.......................23-69
BULKHEAD TRIM PANEL -
INSTALLATION, BACKLITE..............23-81
BULKHEAD TRIM PANEL - REMOVAL.....23-69
BULKHEAD TRIM PANEL - REMOVAL,
BACKLITE..........................23-81
BUMPER - STEP - INSTALLATION, REAR
. . . 13-3
BUMPER - STEP - REMOVAL, REAR
.......13-3
BUMPER - STEPS - INSTALLATION,
FRONT
..............................13-2
BUMPER - STEPS - REMOVAL, FRONT
.....13-2
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF
................21-102BUSHINGS - INSTALLATION..............2-3
BUSHINGS - REMOVAL..................2-3
BUZZ, SQUEAK & RATTLE - STANDARD
PROCEDURE........................23-10
CABIN HEATER - DESCRIPTION.........24-72
CABIN HEATER - OPERATION...........24-72
CABLE - DESCRIPTION.................8P-3
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT........................21-109
CABLE - INSTALLATION, ANTENNA BODY . . 8A-1
CABLE - INSTALLATION, GEARSHIFT....21-109
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-2
CABLE - INSTALLATION, LATCH RELEASE . 23-51
CABLE - INSTALLATION, PARK LOCK....21-126
CABLE - REMOVAL, ANTENNA BODY......8A-1
CABLE - REMOVAL, GEARSHIFT........21-109
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-1
CABLE - REMOVAL, LATCH RELEASE.....23-51
CABLE - REMOVAL, PARK LOCK........21-125
CABLE TENSIONER - INSTALLATION......5-23
CABLE TENSIONER - REMOVAL..........5-23
CABLES - ADJUSTMENT, PARKING
BRAKE..............................5-25
CABLES - DESCRIPTION, BATTERY.......8F-14
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-14
CABLES - INSTALLATION, BATTERY......8F-16
CABLES - INSTALLATION, MODE DOOR . . . 24-19
CABLES - OPERATION, BATTERY........8F-14
CABLES - REMOVAL, BATTERY..........8F-16
CABLES - REMOVAL, MODE DOOR.......24-19
CAMSHAFT POSITION - STANDARD
PROCEDURE, CHECKING................9-27
CAMSHAFT POSITION SENSOR -
DESCRIPTION.......................14-19
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................14-19
CAMSHAFT POSITION SENSOR -
OPERATION.........................14-19
CAMSHAFT POSITION SENSOR -
REMOVAL..........................14-19
CAMSHAFT(S) - INSTALLATION..........9-29
CAMSHAFT(S) - REMOVAL..............9-28
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-18
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-19
CAP - OPERATION, RADIATOR
PRESSURE..........................7-18
CAPACITIES - SPECIFICATIONS, FLUID......0-4
CAPACITY, SPECIFICATIONS - CHARGE . . . 24-49
CARGO/DOME LAMP BULB -
INSTALLATION.......................8L-27
CARGO/DOME LAMP BULB - REMOVAL . . . 8L-27
CARGO/DOME LAMP UNIT -
INSTALLATION.......................8L-28
CARGO/DOME LAMP UNIT - REMOVAL . . . 8L-28
CARPETS AND FLOOR MATS -
INSTALLATION.......................23-70
CARPETS AND FLOOR MATS - REMOVAL . 23-69
CARRIER - INSTALLATION, SPARE TIRE . . . 22-10
CARRIER - REMOVAL, SPARE TIRE......22-10
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-3
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING
......................21-102
CAUTION - CAUTION
..................24-45
CAUTION - REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS
.................24-45
CAUTION, CAUTION
...................24-45
CAUTION, INTERIOR
..................23-67
CENTER - DESCRIPTION, POWER
DISTRIBUTION
....................8W-97-3
CENTER - OPERATION, POWER
DISTRIBUTION
....................8W-97-3
CENTER BEARING - INSTALLATION
........3-9
CENTER BEARING - REMOVAL
............3-8
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL
..................23-55
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL
..................23-55
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION
.................8L-7
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL
.....................8L-7CENTER HIGH MOUNTED STOP LAMP
UN - INSTALLATION...................8L-8
CENTER HIGH MOUNTED STOP LAMP
UN - REMOVAL.......................8L-8
CENTER ROLLER ARM - INSTALLATION . . . 23-38
CENTER ROLLER ARM - REMOVAL......23-37
CENTER TRACK - INSTALLATION........23-39
CENTER TRACK - REMOVAL............23-38
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-13
CENTRAL TIMER MODULE -
DESCRIPTION........................8E-1
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING........................8E-2
CENTRAL TIMER MODULE -
INSTALLATION........................8E-2
CENTRAL TIMER MODULE - OPERATION . . . 8E-2
CENTRAL TIMER MODULE - REMOVAL....8E-2
CHAIN - INSTALLATION, OIL PUMP.......9-54
CHAIN - INSTALLATION, TIMING.........9-67
CHAIN - REMOVAL, OIL PUMP...........9-53
CHAIN - REMOVAL, TIMING.............9-63
CHAIN COVER - INSTALLATION, TIMING . . . 9-60
CHAIN COVER - REMOVAL, TIMING.......9-59
CHAIN TENSIONER - INSTALLATION,
TIMING.............................9-71
CHAIN TENSIONER - REMOVAL, TIMING . . . 9-70
CHAIN TENSIONING RAIL -
INSTALLATION, TIMING.................9-66
CHAIN TENSIONING RAIL - REMOVAL,
TIMING.............................9-63
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-48
CHARGE AIR COOLER AND PLUMBING -
CLEANING...........................11-5
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION........................11-4
CHARGE AIR COOLER AND PLUMBING -
INSPECTION.........................11-5
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION........................11-5
CHARGE AIR COOLER AND PLUMBING -
OPERATION..........................11-4
CHARGE AIR COOLER AND PLUMBING -
REMOVAL...........................11-5
CHARGE AIR COOLER SYSTEM - LEAKS
- DIAGNOSIS AND TESTING.............11-4
CHARGE CAPACITY, SPECIFICATIONS.....24-49
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-13
CHARGING INDICATOR - OPERATION.....8J-13
CHART - SPECIFICATIONS, TORQUE....5-29,5-5
CHART - SPECIFICATIONS, TORQUE.....19-10,
19-14,19-5,19-9
CHART - SPECIFICATIONS, TORQUE....2-12,2-2
CHART, SPECIFICATIONS - TORQUE.......5-22
CHART, SPECIFICATIONS - TORQUE.......22-5
CHECK - INSTALLATION..........23-13,23-24
CHECK - REMOVAL..............23-13,23-24
CHECK OIL LEVEL - STANDARD
PROCEDURE.......................21-102
CHECK VALVE - DESCRIPTION...........8R-7
CHECK VALVE - INSTALLATION..........8R-7
CHECK VALVE - OPERATION.............8R-7
CHECK VALVE - REMOVAL..............8R-7
CHECKING AND REPAIRING
CONNECTING RODS - STANDARD
PROCEDURE.........................9-40
CHECKING BATTERY ELECTROLYTE
LEVEL - STANDARD PROCEDURE........8F-12
CHECKING CAMSHAFT POSITION -
STANDARD PROCEDURE................9-27
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-2
CHIME/BUZZER - DESCRIPTION..........8B-1
CHIME/BUZZER - OPERATION............8B-1
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-1
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING
.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION
. 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL
. . 8W-97-2
CIRCUIT BREAKER - DESCRIPTION
....8W-97-2
CIRCUIT BREAKER - DIAGNOSIS AND
TESTING
.........................8W-97-2
VAINDEX 3
Description Group-Page Description Group-Page Description Group-Page

HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-27
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-31
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-32
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-31
HEAD - INSTALLATION, CYLINDER........9-25
HEAD - REMOVAL, CYLINDER...........9-22
HEAD BOLT INSPECTION - STANDARD
PROCEDURE, CYLINDER................9-21
HEAD COVER(S) - INSTALLATION,
CYLINDER...........................9-30
HEAD COVER(S) - REMOVAL, CYLINDER . . . 9-30
HEAD FRONT COVER - INSTALLATION,
CYLINDER...........................9-26
HEAD FRONT COVER - REMOVAL,
CYLINDER...........................9-23
HEAD GUIDE RAIL - INSTALLATION,
CYLINDER...........................9-26
HEAD GUIDE RAIL - REMOVAL,
CYLINDER...........................9-24
HEAD SURFACE - STANDARD
PROCEDURE, MEASURE CYLINDER.......9-21
HEADLAMP BULB - INSTALLATION, HIGH
BEAM..............................8L-17
HEADLAMP BULB - INSTALLATION, LOW
BEAM..............................8L-19
HEADLAMP BULB - REMOVAL, HIGH
BEAM..............................8L-17
HEADLAMP BULB - REMOVAL, LOW
BEAM...............................8L-18
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-16
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-15
HEADLAMP LEVELING SWITCH -
INSTALLATION.......................8L-17
HEADLAMP LEVELING SWITCH -
REMOVAL..........................8L-16
HEADLINER - INSTALLATION...........23-71
HEADLINER - REMOVAL...............23-70
HEADREST - INSTALLATION............23-76
HEADREST - REMOVAL................23-76
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-3
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-3
HEATED SEAT ELEMENT - OPERATION.....8G-3
HEATED SEAT RELAY - DESCRIPTION.....8G-4
HEATED SEAT RELAY - DIAGNOSIS AND
TESTING............................8G-4
HEATED SEAT RELAY - INSTALLATION.....8G-4
HEATED SEAT RELAY - OPERATION.......8G-4
HEATED SEAT RELAY - REMOVAL........8G-4
HEATED SEAT SENSOR - DESCRIPTION....8G-4
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SWITCH - DESCRIPTION,
DRIVER.............................8G-2
HEATED SEAT SWITCH - DESCRIPTION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, DRIVER.................8G-2
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, PASSENGER.............8G-5
HEATED SEAT SWITCH - INSTALLATION,
DRIVER.............................8G-3
HEATED SEAT SWITCH - INSTALLATION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - OPERATION,
DRIVER.............................8G-2
HEATED SEAT SWITCH - OPERATION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - REMOVAL,
DRIVER.............................8G-3
HEATED SEAT SWITCH - REMOVAL,
PASSENGER.........................8G-5
HEATED SEATS - DESCRIPTION..........8G-1
HEATED SEATS - DIAGNOSIS AND
TESTING............................8G-2
HEATED SEATS - OPERATION
............8G-2
HEATER - DCHA - DIAGNOSIS AND
TESTING, DIESEL SUPPLEMENTAL
.......24-72
HEATER - DESCRIPTION, CABIN
.........24-72
HEATER - INSTALLATION, ENGINE
BLOCK
..............................7-14
HEATER - OPERATION, CABIN
...........24-72HEATER - REMOVAL, ENGINE BLOCK......7-14
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-2
HEATER CONTROL - DESCRIPTION, A/C . . . 24-12
HEATER CONTROL - INSTALLATION, A/C . . 24-13
HEATER CONTROL - OPERATION, A/C....24-12
HEATER CONTROL - REMOVAL, A/C......24-12
HEATER CORE - DESCRIPTION..........24-57
HEATER CORE - INSTALLATION.........24-58
HEATER CORE - OPERATION............24-57
HEATER CORE - REMOVAL.............24-58
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-4
HI PRESSURE FUEL SHUTOFF SOL -
DESCRIPTION.......................14-16
HI PRESSURE FUEL SHUTOFF SOL -
OPERATION.........................14-16
HIGH BEAM HEADLAMP BULB -
INSTALLATION.......................8L-17
HIGH BEAM HEADLAMP BULB -
REMOVAL..........................8L-17
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-17
HIGH BEAM INDICATOR - OPERATION....8J-17
HIGH FUEL SYSTEM PRESSURE -
WARNING...........................14-1
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER................8L-7
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER....................8L-7
HIGH MOUNTED STOP LAMP UN -
INSTALLATION, CENTER................8L-8
HIGH MOUNTED STOP LAMP UN -
REMOVAL, CENTER....................8L-8
HIGH PRESSURE FUEL LINES -
DIAGNOSIS AND TESTING..............14-1
HIGH PRESSURE LINES - INSTALLATION . . . 14-7
HIGH PRESSURE LINES - REMOVAL......14-6
HIGH PRESSURE PUMP - DESCRIPTION . . . 14-7
HIGH PRESSURE PUMP - INSTALLATION . . 14-10
HIGH PRESSURE PUMP - REMOVAL......14-8
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-6
HINGE - INSTALLATION......23-17,23-34,23-50
HINGE - REMOVAL.........23-17,23-34,23-50
HITCH - INSTALLATION, TRAILER........13-10
HITCH - REMOVAL, TRAILER............13-9
HOAT COOLANT - DESCRIPTION..........0-2
HOISTING - STANDARD PROCEDURE.......0-5
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-56
HOLDER - REMOVAL, CUP.............23-55
HOLDING CLUTCH B1 - ASSEMBLY.....21-113
HOLDING CLUTCH B1 - DISASSEMBLY . . 21-112
HOLDING CLUTCH B2 - ASSEMBLY.....21-116
HOLDING CLUTCH B2 - DISASSEMBLY . . 21-115
HOLDING CLUTCHES - DESCRIPTION....21-111
HOLDING CLUTCHES - OPERATION.....21-112
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-5
HOOD - INSTALLATION................23-50
HOOD - REMOVAL....................23-50
HOOD BATTERY INSTALLATION,
INSTALLATION - UNDER...............8F-13
HOOD BATTERY REMOVAL, REMOVAL -
UNDER.............................8F-12
HORN - INSTALLATION.................8H-1
HORN - REMOVAL....................8H-1
HORN SWITCH - INSTALLATION
..........8H-1
HORN SWITCH - REMOVAL
.............8H-1
HOSE - INSTALLATION, INLET
..........24-78
HOSE - INSTALLATION, PRESSURE
......19-15
HOSE - REMOVAL, INLET
..............24-78
HOSE - REMOVAL, PRESSURE
..........19-15
HOSE FROM GEAR TO COOLER TUBE -
INSTALLATION, RETURN
...............19-15
HOSE FROM GEAR TO COOLER TUBE -
REMOVAL, RETURN
..................19-15
HOSES/LINES/TUBES PRECAUTIONS,
CAUTION - REFRIGERANT
..............24-45
HOSES/TUBES - DESCRIPTION, WASHER
. . 8R-8
HOSES/TUBES - OPERATION, WASHER
....8R-9
HOUSING - ASSEMBLY, HVAC
...........24-36
HOUSING - DISASSEMBLY, HVAC
........24-36HOUSING - INSTALLATION, AIR
CLEANER............................9-20
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, REAR A/C....24-41
HOUSING - REMOVAL, AIR CLEANER......9-20
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, REAR A/C........24-40
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
HUB / BEARING - INSTALLATION..........2-5
HUB / BEARING - REMOVAL..............2-4
HUB BEARINGS/SEALS - INSTALLATION,
AXLE...............................3-20
HUB BEARINGS/SEALS - REMOVAL,
AXLE...............................3-20
HUB SEAL - INSTALLATION, TORQUE
CONVERTER.......................21-147
HUB SEAL - REMOVAL, TORQUE
CONVERTER.......................21-147
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-36
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-2
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-5
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IGNITION CONTROL - SPECIAL TOOLS......8I-1
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-10
INBOARD - INSTALLATION.............8O-30
INBOARD - REMOVAL.................8O-29
IN-CAR TEMPERATURE SENSOR -
DESCRIPTION.......................24-19
IN-CAR TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............24-19
IN-CAR TEMPERATURE SENSOR -
OPERATION.........................24-19
IN-CAR TEMPERATURE SENSOR -
REMOVAL..........................24-19
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF............21-102
INDICATOR - DESCRIPTION, ABS.........8J-9
INDICATOR - DESCRIPTION, AIRBAG.....8J-10
INDICATOR - DESCRIPTION, AMBIENT
TEMPERATURE......................8J-11
INDICATOR - DESCRIPTION, BRAKE
WEAR.............................8J-12
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-11
INDICATOR - DESCRIPTION, CHARGING . . . 8J-13
INDICATOR - DESCRIPTION, COOLANT
LOW...............................8J-14
INDICATOR - DESCRIPTION, FUEL
FILTER CLOGGED.....................8J-15
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-17
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-17
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-18
INDICATOR - DESCRIPTION, LOW OIL
LEVEL.............................8J-18
INDICATOR - DESCRIPTION,
MAINTENANCE.......................8J-19
INDICATOR - DESCRIPTION, MULTI-
FUNCTION..........................8J-20
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-22
INDICATOR - DESCRIPTION, TRACTION
CONTROL...........................8J-24
INDICATOR - DESCRIPTION, TRACTION
CONTROL MALFUNCTION..............8J-25
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-25
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-26
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-27
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-27
INDICATOR - OPERATION, ABS...........8J-9
INDICATOR - OPERATION, AIRBAG
.......8J-10
INDICATOR - OPERATION, AMBIENT
TEMPERATURE
......................8J-11
INDICATOR - OPERATION, BRAKE WEAR
. . 8J-12
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-12
INDICATOR - OPERATION, CHARGING
....8J-13
8 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - OPERATION, COOLANT
LOW...............................8J-14
INDICATOR - OPERATION, FUEL FILTER
CLOGGED...........................8J-15
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-17
INDICATOR - OPERATION, HIGH BEAM....8J-17
INDICATOR - OPERATION, LOW FUEL.....8J-18
INDICATOR - OPERATION, LOW OIL
LEVEL.............................8J-18
INDICATOR - OPERATION,
MAINTENANCE.......................8J-19
INDICATOR - OPERATION, MULTI-
FUNCTION..........................8J-21
INDICATOR - OPERATION, SEATBELT.....8J-22
INDICATOR - OPERATION, TRACTION
CONTROL...........................8J-24
INDICATOR - OPERATION, TRACTION
CONTROL MALFUNCTION..............8J-25
INDICATOR - OPERATION, TURN SIGNAL . . 8J-25
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-26
INDICATOR - OPERATION, WASHER
FLUID..............................8J-27
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-28
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-20
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-20
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-12
INJECTOR CLASSIFICATION - STANDARD
PROCEDURE........................14-22
INJECTOR, DESCRIPTION - FUEL........14-20
INJECTORS - STANDARD PROCEDURE,
CLEANING FUEL.....................14-22
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
INLET AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-30
INLET AIR TEMPERATURE SENSOR -
OPERATION.........................14-29
INLET AIR TEMPERATURE SENSOR -
REMOVAL..........................14-30
INLET HOSE - INSTALLATION...........24-78
INLET HOSE - REMOVAL...............24-78
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR...........23-87
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR..............23-87
INPUT SPEED SENSORS - DESCRIPTION . 21-119
INPUT SPEED SENSORS - OPERATION . . . 21-119
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-34,23-37
INSIDE HANDLE ACTUATOR -
REMOVAL.....................23-34,23-37
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - INSTALLATION . . . 8J-9
INSTRUMENT CLUSTER - OPERATION.....8J-5
INSTRUMENT CLUSTER - REMOVAL......8J-7
INSTRUMENT PANEL - INSTALLATION....8L-29
INSTRUMENT PANEL - REMOVAL........8L-28
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-2
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-1
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-61
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-57
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-55
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-55
INSTRUMENT PANEL DUCTS -
INSTALLATION
.......................24-38
INSTRUMENT PANEL DUCTS - REMOVAL
. 24-37
INTAKE MANIFOLD - INSTALLATION
.......9-58
INTAKE MANIFOLD - REMOVAL
..........9-57
INTERIOR - CAUTION
.................23-67INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-25
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-26
INTERIOR LIGHTING - SPECIFICATIONS . . . 8L-26
INTERMEDIATE GEAR - INSTALLATION.....9-66
INTERMEDIATE GEAR - REMOVAL........9-61
INTERMEDIATE SHAFT - INSTALLATION....19-5
INTERMEDIATE SHAFT - REMOVAL.......19-5
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-2
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-9
INTRUSION SENSOR - INSTALLATION.....8Q-2
INTRUSION SENSOR - REMOVAL.........8Q-2
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
ISO FLARING - STANDARD PROCEDURE....5-8
JAMB SWITCH - INSTALLATION, DOOR . . . 8L-31
JAMB SWITCH - REMOVAL, DOOR.......8L-31
JET - DESCRIPTION, OIL................9-51
JET - INSTALLATION, OIL...............9-51
JET - REMOVAL, OIL...................9-51
JOINT - INSTALLATION, LOWER BALL......2-6
JOINT - REMOVAL, LOWER BALL..........2-6
JOURNALS - STANDARD PROCEDURE,
MEASURE CRANKSHAFT AND BLOCK......9-35
JUMP STARTING - STANDARD
PROCEDURE............................0-6
K1 - ASSEMBLY, DRIVING CLUTCH.......21-75
K1 - DISASSEMBLY, DRIVING CLUTCH....21-74
K2 - ASSEMBLY, DRIVING CLUTCH.......21-78
K2 - DISASSEMBLY, DRIVING CLUTCH....21-76
K3 - ASSEMBLY, DRIVING CLUTCH.......21-80
K3 - DISASSEMBLY, DRIVING CLUTCH....21-80
KEY - DESCRIPTION, TRANSPONDER.....8Q-5
KEY - OPERATION, TRANSPONDER.......8Q-5
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY................8Q-2
KEY REMOTE ENTRY MODULE -
INSTALLATION, SENTRY................8Q-4
KEY REMOTE ENTRY MODULE -
OPERATION, SENTRY..................8Q-3
KEY REMOTE ENTRY MODULE -
REMOVAL, SENTRY...................8Q-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-2
KEY/LOCK CYLINDER - INSTALLATION.....19-7
KEY/LOCK CYLINDER - REMOVAL........19-6
KNUCKLE - INSTALLATION...............2-5
KNUCKLE - REMOVAL...................2-5
LAMP BULB - INSTALLATION, BACKUP....8L-6
LAMP BULB - INSTALLATION,
BRAKE/PARK.........................8L-7
LAMP BULB - INSTALLATION,
CARGO/DOME.......................8L-27
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-7
LAMP BULB - INSTALLATION,
CLEARANCE..........................8L-8
LAMP BULB - INSTALLATION,
DOME/READING.....................8L-29
LAMP BULB - INSTALLATION,
ENTRY/EXIT.........................8L-32
LAMP BULB - INSTALLATION, FOG.......8L-10
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-14
LAMP BULB - INSTALLATION, FRONT
TURN/PARK/SIDE MARKER.............8L-15
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP BULB - INSTALLATION, REAR
SIDE MARKER.......................8L-21
LAMP BULB - INSTALLATION, REAR
TURN..............................8L-22
LAMP BULB - INSTALLATION, REPEATER . . 8L-22
LAMP BULB - REMOVAL, BACKUP........8L-5
LAMP BULB - REMOVAL, BRAKE/PARK....8L-7
LAMP BULB - REMOVAL, CARGO/DOME . . 8L-27
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-7
LAMP BULB - REMOVAL, CLEARANCE
.....8L-8
LAMP BULB - REMOVAL, DOME/
READING
...........................8L-29
LAMP BULB - REMOVAL, ENTRY/EXIT
....8L-31
LAMP BULB - REMOVAL, FOG
..........8L-10
LAMP BULB - REMOVAL, FRONT
POSITION
..........................8L-14LAMP BULB - REMOVAL, FRONT
TURN/PARK/SIDE MARKER.............8L-14
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-17
LAMP BULB - REMOVAL, REAR SIDE
MARKER...........................8L-21
LAMP BULB - REMOVAL, REAR TURN....8L-21
LAMP BULB - REMOVAL, REPEATER.....8L-22
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-20
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-20
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING............................8L-9
LAMP RELAY - INSTALLATION, FOG......8L-11
LAMP RELAY - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP RELAY - REMOVAL, FOG.........8L-10
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - INSTALLATION, FOG....8L-12
LAMP SWITCH - REMOVAL, BRAKE.......8L-6
LAMP SWITCH - REMOVAL, FOG........8L-11
LAMP UN - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-8
LAMP UN - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-8
LAMP UNIT - ADJUSTMENT, FRONT......8L-12
LAMP UNIT - INSTALLATION, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - INSTALLATION, CARGO/
DOME...............................8L-28
LAMP UNIT - INSTALLATION,
CLEARANCE..........................8L-9
LAMP UNIT - INSTALLATION, DOME/
READING...........................8L-30
LAMP UNIT - INSTALLATION, ENTRY/
EXIT...............................8L-32
LAMP UNIT - INSTALLATION, FRONT.....8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP UNIT - INSTALLATION, REPEATER . . 8L-23
LAMP UNIT - INSTALLATION, TAIL.......8L-23
LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - REMOVAL, CARGO/DOME . . . 8L-28
LAMP UNIT - REMOVAL, CLEARANCE.....8L-8
LAMP UNIT - REMOVAL, DOME/
READING...........................8L-30
LAMP UNIT - REMOVAL, ENTRY/EXIT....8L-32
LAMP UNIT - REMOVAL, FRONT.........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-18
LAMP UNIT - REMOVAL, REPEATER......8L-22
LAMP UNIT - REMOVAL, TAIL...........8L-23
LAMP/INTRUSION SENSOR -
INSTALLATION, DOME.................8L-31
LAMP/INTRUSION SENSOR - REMOVAL,
DOME.............................8L-31
LAMP/INTRUSION SENSOR BULB -
INSTALLATION, DOME.................8L-30
LAMP/INTRUSION SENSOR BULB -
REMOVAL, DOME....................8L-30
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-3
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS......................8L-5
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-25
LAMPS/LIGHTING - INTERIOR -
OPERATION.........................8L-26
LATCH - INSTALLATION.....23-18,23-35,23-51
LATCH - INSTALLATION, REAR..........23-40
LATCH - INSTALLATION, SAFETY........23-52
LATCH / LOCK CONTROL -
INSTALLATION.......................23-40
LATCH / LOCK CONTROL - REMOVAL.....23-39
LATCH - REMOVAL.........23-18,23-34,23-51
LATCH - REMOVAL, REAR..............23-40
LATCH - REMOVAL, SAFETY............23-52
LATCH RELEASE CABLE - INSTALLATION . . 23-51
LATCH RELEASE CABLE - REMOVAL.....23-51
LATCH RELEASE HANDLE -
INSTALLATION
.......................23-52
LATCH RELEASE HANDLE - REMOVAL
....23-52
LATCH STRIKER - INSTALLATION
........23-18
LATCH STRIKER - INSTALLATION, REAR
. . 23-41
LATCH STRIKER - REMOVAL
...........23-18
VAINDEX 9
Description Group-Page Description Group-Page Description Group-Page

LATCH STRIKER - REMOVAL, REAR......23-41
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK DOWN TEST - STANDARD
PROCEDURE, CYLINDER.................9-3
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-12
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM..........11-4
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM....................7-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-46
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEFT MOUNT - INSTALLATION...........9-49
LEFT MOUNT - REMOVAL...............9-49
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID........21-102
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECK OIL........................21-102
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE......8F-12
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-65
LEVEL INDICATOR - DESCRIPTION, LOW
OIL................................8J-18
LEVEL INDICATOR - OPERATION, LOW
OIL.................................8J-18
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..................14-15
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL.................14-15
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL.....................14-15
LEVEL SENSOR - INSTALLATION,
COOLANT............................7-13
LEVEL SENSOR - REMOVAL, COOLANT....7-13
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-8
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-16
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-15
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-17
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-16
LEVER - INSTALLATION................5-26
LEVER - INSTALLATION, ALB............5-15
LEVER - REMOVAL....................5-26
LEVER - REMOVAL, ALB................5-15
LICENSE PLATE BRACKET -
INSTALLATION.......................23-47
LICENSE PLATE BRACKET - REMOVAL....23-47
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-18
LIGHTER LAMP UNIT - INSTALLATION,
ASH RECEIVER/CIGAR.................8L-27
LIGHTER LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR.....................8L-27
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-1
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-2
LIGHTING - SPECIFICATIONS, INTERIOR . . 8L-26
LINE - DESCRIPTION, REFRIGERANT.....24-44
LINE - INSTALLATION, A/C DISCHARGE . . . 24-54
LINE - INSTALLATION, FUEL............24-76
LINE - INSTALLATION, LIQUID..........24-59
LINE - INSTALLATION, SUCTION.........24-66
LINE - OPERATION, REFRIGERANT
.......24-44
LINE - REMOVAL, A/C DISCHARGE
.......24-53
LINE - REMOVAL, FUEL
................24-75
LINE - REMOVAL, LIQUID
..............24-58
LINE - REMOVAL, SUCTION
............24-66LINE FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN...............19-15
LINE FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN..................19-15
LINES - DIAGNOSIS AND TESTING, HIGH
PRESSURE FUEL......................14-1
LINES - INSTALLATION, HIGH PRESSURE . . 14-7
LINES - INSTALLATION, OIL COOLER......9-50
LINES - INSTALLATION, UNDERBODY....24-69
LINES - REMOVAL, HIGH PRESSURE......14-6
LINES - REMOVAL, OIL COOLER.........9-50
LINES - REMOVAL, UNDERBODY........24-68
LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING
FUEL...............................14-2
LINK - INSTALLATION, STABILIZER....2-16,2-9
LINK - REMOVAL, STABILIZER........2-16,2-9
LINKAGE - DESCRIPTION, WIPER.......8R-17
LINKAGE - INSTALLATION, WIPER.......8R-18
LINKAGE - OPERATION, WIPER.........8R-17
LINKAGE - REMOVAL, WIPER...........8R-17
LIQUID LINE - INSTALLATION...........24-59
LIQUID LINE - REMOVAL..............24-58
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL......8W-01-8
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - INSPECTION, FLUID
FILL/CHECK............................0-4
LOCK CABLE - INSTALLATION, PARK....21-126
LOCK CABLE - REMOVAL, PARK........21-125
LOCK CONTROL - INSTALLATION, LATCH . . 23-40
LOCK CONTROL - REMOVAL, LATCH.....23-39
LOCK CYLINDER - INSTALLATION.......23-18
LOCK CYLINDER - REMOVAL...........23-18
LOCK MOTOR - INSTALLATION, DOOR....8N-1
LOCK MOTOR - REMOVAL, DOOR........8N-1
LOCK SWITCH - DESCRIPTION, MASTER . . . 8N-2
LOCK SWITCH - DIAGNOSIS AND
TESTING, MASTER....................8N-2
LOCK SWITCH - INSTALLATION, MASTER . . 8N-2
LOCK SWITCH - REMOVAL, MASTER......8N-2
LOCKS - DESCRIPTION, POWER.........8N-1
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-34
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-33
LOSS - STANDARD PROCEDURE,
DETERMINING CYLINDER PRESSURE......9-4
LOW BEAM HEADLAMP BULB -
INSTALLATION.......................8L-19
LOW BEAM HEADLAMP BULB -
REMOVAL..........................8L-18
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-18
LOW FUEL INDICATOR - OPERATION.....8J-18
LOW INDICATOR - DESCRIPTION,
COOLANT...........................8J-14
LOW INDICATOR - OPERATION,
COOLANT...........................8J-14
LOW OIL LEVEL INDICATOR -
DESCRIPTION.......................8J-18
LOW OIL LEVEL INDICATOR -
OPERATION.........................8J-18
LOW PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE................14-3
LOW PRESSURE PUMP - DESCRIPTION . . . 14-7
LOW PRESSURE PUMP - INSTALLATION . . 14-11
LOW PRESSURE PUMP - OPERATION.....14-8
LOW PRESSURE PUMP - REMOVAL
.......14-9
LOWER BALL JOINT - INSTALLATION
......2-6
LOWER BALL JOINT - REMOVAL
..........2-6
LOWER CONTROL ARM - INSTALLATION
....2-6
LOWER CONTROL ARM - REMOVAL
.......2-6
LOWER ROLLER ARM - INSTALLATION
. . . 23-38
LOWER ROLLER ARM - REMOVAL
.......23-38
LUBRICANT RECOMMENDATIONS -
STANDARD PROCEDURE, PARTS
..........0-5
MAINTENANCE INDICATOR -
DESCRIPTION
.......................8J-19
MAINTENANCE INDICATOR - OPERATION
. . 8J-19
MAINTENANCE SCHEDULES -
DESCRIPTION
.........................0-7
MALFUNCTION INDICATOR -
DESCRIPTION, TRACTION CONTROL
.....8J-25
MALFUNCTION INDICATOR -
OPERATION, TRACTION CONTROL
.......8J-25MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-20
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-20
MANIFOLD - INSTALLATION, EXHAUST....9-59
MANIFOLD - INSTALLATION, INTAKE......9-58
MANIFOLD - REMOVAL, EXHAUST........9-59
MANIFOLD - REMOVAL, INTAKE..........9-57
MANIFOLD AIR FLOW (MAF) SENSOR -
DESCRIPTION.......................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
INSTALLATION.......................14-31
MANIFOLD AIR FLOW (MAF) SENSOR -
OPERATION.........................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
REMOVAL..........................14-31
MANUAL - INSTALLATION, WINDOW
REGULATOR........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR........................23-22
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-4
MARKER LAMP BULB - INSTALLATION,
FRONT TURN/PARK/SIDE..............8L-15
MARKER LAMP BULB - INSTALLATION,
REAR SIDE.........................8L-21
MARKER LAMP BULB - REMOVAL,
FRONT TURN/PARK/SIDE..............8L-14
MARKER LAMP BULB - REMOVAL, REAR
SIDE..............................8L-21
MASTER CYLINDER - INSTALLATION......5-18
MASTER CYLINDER - REMOVAL...........5-17
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-17
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-16
MASTER LOCK SWITCH - DESCRIPTION . . . 8N-2
MASTER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-2
MASTER LOCK SWITCH - INSTALLATION . . 8N-2
MASTER LOCK SWITCH - REMOVAL......8N-2
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-2
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-70
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-69
MEASURE CRANKSHAFT AND BLOCK
JOURNALS - STANDARD PROCEDURE.....9-35
MEASURE CYLINDER HEAD SURFACE -
STANDARD PROCEDURE................9-21
MEASURING CYLINDER BORES -
STANDARD PROCEDURE................9-34
MEASURING PISTON PROTRUSION -
STANDARD PROCEDURE................9-42
MECHANISM - DESCRIPTION, SHIFT....21-133
MECHANISM - INSTALLATION, SHIFT....21-135
MECHANISM - OPERATION, SHIFT......21-133
MECHANISM - REMOVAL, SHIFT.......21-134
METRIC SYSTEM - DESCRIPTION......Intro.-5
MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE, USING........8F-11
MIRROR - GLASS - INSTALLATION, SIDE
VIEW..............................23-49
MIRROR - GLASS - REMOVAL, SIDE
VIEW..............................23-49
MIRROR - INSTALLATION, SIDE VIEW....23-48
MIRROR - REMOVAL, REAR VIEW.......23-72
MIRROR - REMOVAL, SIDE VIEW
........23-48
MIRROR SUPPORT BRACKET -
INSTALLATION, REAR VIEW
............23-72
MIRROR SWITCH - DIAGNOSIS AND
TESTING, POWER
.....................8N-3
MIRROR SWITCH - INSTALLATION,
POWER
.............................8N-4
MIRROR SWITCH - REMOVAL, POWER
....8N-3
MIRRORS - DESCRIPTION, POWER
.......8N-3
MODE DOOR CABLES - INSTALLATION
. . . 24-19
MODE DOOR CABLES - REMOVAL
.......24-19
MODULE - DESCRIPTION, AIRBAG
CONTROL
...........................8O-8
MODULE - DESCRIPTION, CENTRAL
TIMER
..............................8E-1
MODULE - DESCRIPTION, CONTROL
.....24-24
MODULE - DESCRIPTION, ENGINE
CONTROL
...........................8E-3
MODULE - DESCRIPTION, FUEL TANK
....14-13
10 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-55
PANEL DUCTS - INSTALLATION,
INSTRUMENT.......................24-38
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PARK BRAKE, SPECIAL TOOLS...........5-23
PARK BRAKE SWITCH - INSTALLATION . . . 8L-20
PARK BRAKE SWITCH - REMOVAL.......8L-20
PARK LOCK CABLE - INSTALLATION.....21-126
PARK LOCK CABLE - REMOVAL........21-125
PARKING BRAKE CABLES -
ADJUSTMENT........................5-25
PARK/NEUTRAL CONTACT -
DESCRIPTION......................21-139
PARK/NEUTRAL CONTACT - OPERATION . 21-140
PARTS & LUBRICANT
RECOMMENDATIONS - STANDARD
PROCEDURE..........................0-5
PASSENGER AIRBAG - DESCRIPTION....8O-23
PASSENGER AIRBAG - INSTALLATION....8O-26
PASSENGER AIRBAG - OPERATION......8O-24
PASSENGER AIRBAG - REMOVAL........8O-24
PASSENGER AIRBAG BRACKET -
INSTALLATION......................8O-27
PASSENGER AIRBAG BRACKET -
REMOVAL..........................8O-27
PASSENGER HEATED SEAT SWITCH -
DESCRIPTION.........................8G-5
PASSENGER HEATED SEAT SWITCH -
DIAGNOSIS AND TESTING..............8G-5
PASSENGER HEATED SEAT SWITCH -
INSTALLATION.......................8G-5
PASSENGER HEATED SEAT SWITCH -
OPERATION..........................8G-5
PASSENGER HEATED SEAT SWITCH -
REMOVAL...........................8G-5
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PEDAL - INSTALLATION................5-19
PEDAL - REMOVAL....................5-18
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR..........14-17
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-4
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, A/C........................24-3
PILLAR - INSTALLATION, REAR.........8L-29
PILLAR - REMOVAL, REAR.............8L-28
PINION SEAL - INSTALLATION...........3-22
PINION SEAL - REMOVAL...............3-22
PIPE - INSTALLATION, EXHAUST.........11-3
PIPE - REMOVAL, EXHAUST.............11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON PROTRUSION - STANDARD
PROCEDURE, MEASURING..............9-42
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-46
PISTONS - DESCRIPTION.............21-128
PISTONS - OPERATION...............21-128
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-131
PLANETARY GEARTRAIN - DESCRIPTION . 21-130
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-131
PLANETARY GEARTRAIN - OPERATION . . 21-130
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE BRACKET - INSTALLATION,
LICENSE...........................23-47
PLATE BRACKET - REMOVAL, LICENSE . . . 23-47
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-18
PLATES - INSTALLATION, SPRING
CLAMP..............................2-8
PLATES - INSTALLATION, SPRING STOP....2-9
PLATES - REMOVAL, SPRING CLAMP
......2-8
PLATES - REMOVAL, SPRING STOP
........2-9
PLUG - INSTALLATION, GLOW
............8I-1
PLUG - REMOVAL, GLOW
...............8I-1
PLUG RELAY - DESCRIPTION, GLOW
......8I-2PLUG RELAY - OPERATION, GLOW........8I-2
PLUG RELAYS - DIAGNOSIS AND
TESTING, GLOW.......................8I-2
PLUGS - STANDARD PROCEDURE,
REPLACING ENGINE CORE AND OIL
GALLERY............................9-34
PLUMBING - CLEANING, CHARGE AIR
COOLER.............................11-5
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER.........................11-4
PLUMBING - INSPECTION, CHARGE AIR
COOLER.............................11-5
PLUMBING - INSTALLATION, CHARGE
AIR COOLER.........................11-5
PLUMBING - OPERATION, CHARGE AIR
COOLER.............................11-4
PLUMBING - REMOVAL, CHARGE AIR
COOLER.............................11-5
PLUMBING - WARNING................24-44
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISH - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-75
POSITION - STANDARD PROCEDURE,
CHECKING CAMSHAFT.................9-27
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-14
POSITION LAMP BULB - REMOVAL,
FRONT.............................8L-14
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-17
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-19
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT.......................14-20
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-19
POSITION SENSOR - INSTALLATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-19
POSITION SENSOR - OPERATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-19
POSITION SENSOR - REMOVAL,
CRANKSHAFT.......................14-20
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-7
POWER - INSTALLATION, WINDOW
REGULATOR........................23-21
POWER - REMOVAL, WINDOW
REGULATOR........................23-20
POWER BRAKE BOOSTER -
DESCRIPTION........................5-19
POWER BRAKE BOOSTER -
INSTALLATION........................5-19
POWER BRAKE BOOSTER - OPERATION . . . 5-19
POWER BRAKE BOOSTER - REMOVAL.....5-19
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-3
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-3
POWER LOCKS - DESCRIPTION..........8N-1
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING........................8N-3
POWER MIRROR SWITCH -
INSTALLATION.......................8N-4
POWER MIRROR SWITCH - REMOVAL....8N-3
POWER MIRRORS - DESCRIPTION.......8N-3
POWER OUTLET - DESCRIPTION......8W-97-3
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-4
POWER OUTLET - INSTALLATION.....8W-97-4
POWER OUTLET - OPERATION........8W-97-4
POWER OUTLET - REMOVAL.........8W-97-4
POWER STEERING FLUID -
DESCRIPTION
.........................0-3
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE
. . . 19-12
POWER STEERING PUMP FILL AND
BLEED PROCEDURE, STANDARD
PROCEDURE
........................19-14
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING
..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING
.....19-13POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING........................8N-5
POWER WINDOW SWITCH -
INSTALLATION.......................8N-6
POWER WINDOW SWITCH - REMOVAL....8N-6
POWER WINDOWS - DESCRIPTION.......8N-5
POWER WINDOWS - OPERATION.........8N-5
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-8
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING..............2-17
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, CAUTION -
REFRIGERANT HOSES/LINES/TUBES......24-45
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY.................23-82
PRELIMINARY - DIAGNOSIS AND
TESTING...........................21-23
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-1
PRESSURE - WARNING, HIGH FUEL
SYSTEM............................14-1
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-18
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-19
PRESSURE CAP - OPERATION,
RADIATOR...........................7-18
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE...................22-6
PRESSURE FUEL LINES - DIAGNOSIS
AND TESTING, HIGH...................14-1
PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE, LOW...........14-3
PRESSURE FUEL SHUTOFF SOL -
DESCRIPTION, HI....................14-16
PRESSURE FUEL SHUTOFF SOL -
OPERATION, HI......................14-16
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-8
PRESSURE HOSE - INSTALLATION.......19-15
PRESSURE HOSE - REMOVAL..........19-15
PRESSURE LINES - INSTALLATION, HIGH . . 14-7
PRESSURE LINES - REMOVAL, HIGH......14-6
PRESSURE LOSS - STANDARD
PROCEDURE, DETERMINING
CYLINDER............................9-4
PRESSURE PUMP - DESCRIPTION, HIGH . . . 14-7
PRESSURE PUMP - DESCRIPTION, LOW . . . 14-7
PRESSURE PUMP - INSTALLATION,
HIGH..............................14-10
PRESSURE PUMP - INSTALLATION, LOW . 14-11
PRESSURE PUMP - OPERATION, LOW.....14-8
PRESSURE PUMP - REMOVAL, HIGH......14-8
PRESSURE PUMP - REMOVAL, LOW......14-9
PRESSURE SENSOR - DESCRIPTION,
BOOST.............................14-17
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, BOOST.....................14-18
PRESSURE SENSOR - INSTALLATION,
BOOST.............................14-18
PRESSURE SENSOR - OPERATION,
BOOST.............................14-18
PRESSURE SENSOR - REMOVAL, BOOST . . 14-18
PRESSURE SOLENOID - DESCRIPTION,
FUEL..............................14-27
PRESSURE SOLENOID - INSTALLATION,
FUEL..............................14-28
PRESSURE SOLENOID - OPERATION,
FUEL..............................14-27
PRESSURE SOLENOID - REMOVAL, FUEL . 14-28
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-13
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-13
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-14
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-13
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-14
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PROP ROD - INSTALLATION
............23-52
12 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

PROP ROD - REMOVAL................23-52
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - INSTALLATION.......3-6
PROPELLER SHAFT - REMOVAL...........3-6
PROPELLER SHAFT - SPECIAL TOOLS......3-5
PROPELLER SHAFT - SPECIFICATIONS......3-5
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROTRUSION - STANDARD PROCEDURE,
MEASURING PISTON...................9-42
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-19
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-21
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-19
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-20
PUMP - ASSEMBLY, OIL..............21-121
PUMP - DESCRIPTION................19-12
PUMP - DESCRIPTION, ELECTRIC
COOLANT...........................24-57
PUMP - DESCRIPTION, FUEL DOSING....24-74
PUMP - DESCRIPTION, HIGH PRESSURE . . . 14-7
PUMP - DESCRIPTION, LOW PRESSURE . . . 14-7
PUMP - DESCRIPTION, OIL............21-120
PUMP - DESCRIPTION, VACUUM.........9-48
PUMP - DISASSEMBLY, OIL...........21-120
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-12
PUMP - INSTALLATION, ELECTRIC
COOLANT...........................24-57
PUMP - INSTALLATION, FUEL DOSING....24-74
PUMP - INSTALLATION, HIGH
PRESSURE.........................14-10
PUMP - INSTALLATION, LOW PRESSURE . 14-11
PUMP - INSTALLATION, VACUUM.........9-49
PUMP - INSTALLATION, WATER..........7-20
PUMP - OPERATION..................19-12
PUMP - OPERATION, ELECTRIC
COOLANT...........................24-57
PUMP - OPERATION, FUEL DOSING......24-74
PUMP - OPERATION, LOW PRESSURE.....14-8
PUMP - OPERATION, OIL.............21-120
PUMP - OPERATION, VACUUM...........9-48
PUMP - REMOVAL, ELECTRIC COOLANT . . 24-57
PUMP - REMOVAL, FUEL DOSING.......24-74
PUMP - REMOVAL, HIGH PRESSURE......14-8
PUMP - REMOVAL, LOW PRESSURE......14-9
PUMP - REMOVAL, VACUUM............9-48
PUMP - REMOVAL, WATER..............7-19
PUMP CHAIN - INSTALLATION, OIL.......9-54
PUMP CHAIN - REMOVAL, OIL...........9-53
PUMP FILL AND BLEED PROCEDURE,
STANDARD PROCEDURE - POWER
STEERING..........................19-14
PUMP LEAKAGE - DIAGNOSIS AND
TESTING...........................19-12
PUMP TEST - STANDARD PROCEDURE,
LOW PRESSURE FUEL.................14-3
PUMP TO COOLER TUBE -
INSTALLATION, RETURN LINE FROM.....19-15
PUMP TO COOLER TUBE - REMOVAL,
RETURN LINE FROM..................19-15
PUMP/MOTOR - DESCRIPTION, WASHER . . 8R-9
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-10
PUMP/MOTOR - OPERATION, WASHER . . . 8R-10
PUMP/MOTOR - REMOVAL, WASHER....8R-10
QUARTER TRIM PANEL - INSTALLATION . . 23-72
QUARTER TRIM PANEL - REMOVAL......23-71
QUARTER WINDOW - INSTALLATION.....23-81
QUARTER WINDOW - REMOVAL.........23-81
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - INSTALLATION.............7-17
RADIATOR - REMOVAL.................7-16
RADIATOR CROSSMEMBER -
INSTALLATION.......................23-48
RADIATOR CROSSMEMBER - REMOVAL . . 23-47
RADIATOR FAN - INSTALLATION
..........7-13
RADIATOR FAN - REMOVAL
.............7-13
RADIATOR PRESSURE CAP -
DESCRIPTION
........................7-18
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING
........................7-19
RADIATOR PRESSURE CAP - OPERATION
. . 7-18RADIO - INSTALLATION................8A-2
RADIO - REMOVAL....................8A-2
RAIL - DESCRIPTION, FUEL............14-11
RAIL - INSTALLATION, CYLINDER HEAD
GUIDE..............................9-26
RAIL - INSTALLATION, FUEL............14-11
RAIL - INSTALLATION, TENSIONING AND
SLIDE..............................9-66
RAIL - INSTALLATION, TIMING CHAIN
TENSIONING.........................9-66
RAIL - OPERATION, FUEL..............14-11
RAIL - REMOVAL, CYLINDER HEAD
GUIDE..............................9-24
RAIL - REMOVAL, FUEL...............14-11
RAIL - REMOVAL, TIMING CHAIN
TENSIONING.........................9-63
RAILS - REMOVAL, TENSIONING AND
SLIDE..............................9-61
RATTLE - STANDARD PROCEDURE,
BUZZ, SQUEAK......................23-10
REAR - DESCRIPTION..................2-11
REAR - INSTALLATION.........5-14,5-22,5-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-37
REAR - INSTALLATION, SEAT...........23-79
REAR - INSTALLATION, SEAT BACK
CUSHION/COVER.....................23-80
REAR - INSTALLATION, SEAT CUSHION/
COVER.............................23-80
REAR - REMOVAL.............5-13,5-22,5-24
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-37
REAR - REMOVAL, SEAT...............23-79
REAR - REMOVAL, SEAT BACK
CUSHION/COVER.....................23-80
REAR - REMOVAL, SEAT CUSHION/
COVER.............................23-80
REAR (15º WHEELS) (SRW) - REMOVAL....5-9
REAR (16º WHEELS) (SRW) -
INSTALLATION........................5-11
REAR (16º WHEELS) (SRW) - REMOVAL....5-9
REAR A/C HOUSING - INSTALLATION.....24-41
REAR A/C HOUSING - REMOVAL........24-40
REAR AXLE - DESCRIPTION.............3-10
REAR AXLE - DIAGNOSIS AND TESTING . . . 3-10
REAR AXLE - INSTALLATION............3-12
REAR AXLE - OPERATION...............3-10
REAR AXLE - REMOVAL................3-11
REAR AXLE - SPECIAL TOOLS...........3-14
REAR AXLE - SPECIFICATIONS...........3-13
REAR BUMPER - STEP - INSTALLATION . . . 13-3
REAR BUMPER - STEP - REMOVAL.......13-3
REAR CROSSMEMBER - TRANSMISSION
- INSTALLATION......................13-9
REAR CROSSMEMBER - TRANSMISSION
- REMOVAL..........................13-9
REAR DRUM IN HAT BRAKE - CLEANING . . . 5-27
REAR (DRW) - INSTALLATION . . . 5-11,5-13,5-21
REAR (DRW) - REMOVAL.......5-10,5-12,5-20
REAR EVAPORATOR - INSTALLATION.....24-61
REAR EVAPORATOR - REMOVAL........24-60
REAR EXPANSION VALVE -
INSTALLATION.......................24-63
REAR EXPANSION VALVE - REMOVAL....24-62
REAR FASCIA - INSTALLATION...........13-3
REAR FASCIA - REMOVAL...............13-3
REAR LATCH - INSTALLATION..........23-40
REAR LATCH - REMOVAL..............23-40
REAR LATCH STRIKER - INSTALLATION . . . 23-41
REAR LATCH STRIKER - REMOVAL......23-41
REAR PILLAR - INSTALLATION..........8L-29
REAR PILLAR - REMOVAL.............8L-28
REAR SEAT BACK SHIELD -
INSTALLATION.......................23-79
REAR SEAT BACK SHIELD - REMOVAL....23-79
REAR SEAT BELT & RETRACTOR -
INSTALLATION......................8O-29
REAR SEAT BELT & RETRACTOR -
REMOVAL..........................8O-27
REAR SIDE MARKER LAMP BULB -
INSTALLATION.......................8L-21
REAR SIDE MARKER LAMP BULB -
REMOVAL
..........................8L-21
REAR (SRW) - INSTALLATION
.......5-13,5-21
REAR (SRW) - REMOVAL
...........5-12,5-20
REAR TURN LAMP BULB -
INSTALLATION
.......................8L-22
REAR TURN LAMP BULB - REMOVAL
....8L-21REAR VIEW MIRROR - REMOVAL........23-72
REAR VIEW MIRROR SUPPORT
BRACKET - INSTALLATION.............23-72
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL.........22-12
REAR WHEEL SPEED SENSOR -
INSTALLATION........................5-31
REAR WHEEL SPEED SENSOR -
REMOVAL...........................5-30
REAR WHEELS - INSTALLATION, AXLE
SHAFTS - DUAL.......................3-19
REAR WHEELS - REMOVAL, AXLE
SHAFTS - DUAL.......................3-19
RECEIVER - INSTALLATION, ASH........23-55
RECEIVER - REMOVAL, ASH............23-55
RECEIVER/CIGAR LIGHTER LAMP UNIT -
INSTALLATION, ASH..................8L-27
RECEIVER/CIGAR LIGHTER LAMP UNIT -
REMOVAL, ASH......................8L-27
RECEIVER/DRIER - DESCRIPTION........24-64
RECEIVER/DRIER - INSTALLATION.......24-64
RECEIVER/DRIER - OPERATION.........24-64
RECEIVER/DRIER - REMOVAL...........24-64
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION.......................24-20
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-21
RECIRCULATION DOOR ACTUATOR -
OPERATION.........................24-20
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-21
RECOMMENDATIONS - STANDARD
PROCEDURE, PARTS & LUBRICANT........0-5
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-47
REFERENCES - DESCRIPTION, TORQUE . . Intro.-7
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-12
REFRIGERANT - DESCRIPTION..........24-65
REFRIGERANT - OPERATION............24-65
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS, CAUTION..............24-45
REFRIGERANT LINE - DESCRIPTION......24-44
REFRIGERANT LINE - OPERATION.......24-44
REFRIGERANT OIL - DESCRIPTION......24-65
REFRIGERANT OIL - OPERATION........24-65
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-65
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-47
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-48
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-46
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-46
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-23
REGULATOR - MANUAL - INSTALLATION,
WINDOW...........................23-23
REGULATOR - MANUAL - REMOVAL,
WINDOW...........................23-22
REGULATOR - POWER - INSTALLATION,
WINDOW...........................23-21
REGULATOR - POWER - REMOVAL,
WINDOW...........................23-20
RELAY - DESCRIPTION..............8W-97-4
RELAY - DESCRIPTION, BLOWER
MOTOR
............................24-23
RELAY - DESCRIPTION, GLOW PLUG
......8I-2
RELAY - DESCRIPTION, HEATED SEAT
.....8G-4
RELAY - DESCRIPTION, STARTER
MOTOR
............................8F-31
RELAY - DESCRIPTION, WIPER
.........8R-20
RELAY - DIAGNOSIS AND TESTING
....8W-97-5
RELAY - DIAGNOSIS AND TESTING,
BLOWER MOTOR
....................24-24
RELAY - DIAGNOSIS AND TESTING,
HEATED SEAT
........................8G-4
RELAY - INSTALLATION
.............8W-97-5
RELAY - INSTALLATION, BLOWER
MOTOR
............................24-24
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP
......................8L-9
RELAY - INSTALLATION, FOG LAMP
......8L-11
RELAY - INSTALLATION, HEATED SEAT
....8G-4
VAINDEX 13
Description Group-Page Description Group-Page Description Group-Page