2005 MERCEDES-BENZ SLK CLASS turn signal

206 Controls in detailAudio systemObtaining additional text information
Additional text information (artist, title)
related to the current channel can be
displayed.
Press
INF
soft key.
The title being played is displayed.

Press
INF
soft key again.
The name of the artist performing the
title being played is displayed.Storing stations

Tune in desired station.

Press and hold desired station
button1 to R until a brief signal
tone is heard.
The frequency is stored on the selected
station button.
The radio saves the current station at
the memory preset selected. The
memory preset selected appears in the
status line, e.g. S3.Calling up the ESN information menu

Press
INF
soft key.

Press
ESN
soft key.
The twelve-digit electronic serial
number (ESN) of the SAT tuner*
installed in your vehicle is displayed.

Press
RET
soft key to exit the menu.
iIf a button is not pressed within
four seconds, the radio will return to
the standard display.
iThere are ten presets available.
An existing entry is overwritten in the
memory list when a new entry is given.

267 Controls in detail
Useful features
Step 3:
Hold the end of hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping indicator lamp4 in view.
Step 4:

Using both hands, simultaneously
press hand-held transmitter button5
and desired integrated signal transmit-
ter button (1,2 or3). Do not re-
lease the buttons until completing
step 5.
Indicator lamp4 on the integrated re-
mote control will flash, first slowly and
then rapidly.Step 5:

When indicator lamp4 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe indicator lamp4.
If indicator lamp4 stays on constant-
ly, programming is complete and your
device should activate when the inte-
grated signal transmitter button is
pressed and released.Step 7:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
iThe indicator lamp4 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after
20 seconds.
iIf the indicator lamp4 flashes rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code” feature.

270 Controls in detailUseful featuresReprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Press and hold desired signal transmit-
ter button (1,2 or3). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.Heated steering wheel*
(SLK 350, Canada only)
The steering wheel heating warms up the
leather area of the steering wheel.
The lever is on the lower left-hand side of
the steering wheel.
1Switching on
2Indicator lamp
3Switching offSwitching on

Switch on the ignition (
page 35).

Turn switch at tip of lever in direction of
arrow1 and release it.
Indicator lamp2 comes on.
The steering wheel heating switches
on.
Switching off

Turn switch at tip of lever in direction of
arrow3 and release it.
The steering wheel heating switches
off.
Indicator lamp2 goes out.iThe heating of the steering wheel de-
pends on the current temperature.
The steering wheel heating switches off
automatically when you remove the
SmartKey from the starter switch.

337 Operation
Vehicle care
To prevent damage to the antenna, un-
screw and remove antenna on left rear
side of vehicle before taking the vehicle
through a car wash. Note that without the
antenna on the left rear side of the vehicle
installed, the signaling range of the
SmartKey is considerably reduced. Hold
the SmartKey in close proximity towards
the antenna base when locking and un-
locking the vehicle.
In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the undercarriage, do not
forget to clean the inner sides of the
wheels.Ornamental moldings
For regular cleaning and care of very dirty
chrome-plated parts, use a chrome clean-
er.
Headlamps, side makers, tail lamps,
turn signal lenses
Use a mild car wash detergent, such as
Mercedes-Benz approved Car Shampoo,
with plenty of water.
To prevent scratches, never apply strong
force and use only a soft, non-scratchy
cloth when cleaning the lenses. Do not at-
tempt to wipe dirty lenses with a dry cloth
or sponge.Wiper blades

Switch on wipers and place them in a
vertical position.
For information on placing the wipers
in a vertical position, see “Replacing
wiper blades” (
page 386).
!The windshield wipers must be in a ver-
tical position before folding them away
from the windshield. They could other-
wise damage the hood.


349 Practical hints
What to do if …
On the pages that follow, you will find a
compilation of the most important warning
and malfunction messages that may ap-
pear in the multifunction display.
For your convenience the messages are
divided into two sections:

Text messages (
page 350)


Symbol messages (
page 355)
Warning!
G
No messages will be displayed if either the
instrument cluster or the multifunction dis-
play is inoperative.
Contact your nearest authorized
Mercedes-Benz Center.
iSwitching on ignition (
page 35)
causes all instrument cluster lamps
(except high beam headlamp indicator
lamp and turn signal indicator lamps
unless activated) as well as the multi-
function display to come on. Make sure
the lamps and multifunction display are
in working order before starting your
journey.

367 Practical hints
What to do if …
.
Turn signal in
mirror, left
The left turn signal in the side mirror
is malfunctioning. This message will
only appear if a critical number of
LEDs have stopped working.

Visit an authorized Mercedes-Benz Center
as soon as possible.
Turn signal in
mirror, right
The right turn signal in the side mir-
ror is malfunctioning. This message
will only appear if a critical number
of LEDs have stopped working.

Visit an authorized Mercedes-Benz Center
as soon as possible.
Turn signal
,
front left
The left front turn signal is malfunc-
tioning.

Replace the bulb as soon as possible.
Turn signal
,
front right
The right front turn signal is mal-
functioning.

Replace the bulb as soon as possible.
Rear left turn signal
Back-up lamp on
The left rear turn signal is malfunc-
tioning. A backup bulb has been
brought into use.

Replace the bulb as soon as possible.
Rear right turn signal
Back-up lamp on
The right rear turn signal is malfunc-
tioning. A backup bulb has been
brought into use.

Replace the bulb as soon as possible.
Display symbol
Display message
Possible cause
Possible solution

381 Practical hints
Replacing bulbs
Front lamps Rear lamps
Lamp
Type
1
Additional turn signal
lamp
LED
2
Turn signal lamp
PY 21 W
3
Halogen headlamp:
Low beam
Bi-Xenon* headlamp:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Bi-Xenon* bulbs yourself. See an
authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35W
4
Front fog lamp
HB4 (51 W)
5
Parking and standing
lamp
W5W
6
Halogen headlamp:
High beam/high beam
flasher
Bi-Xenon* headlamp:
High beam flasher
H7 (55 W)
H7 (55 W)
7
Side marker lamp
W5W
Lamp
Type
8
Rear fog lamp (driver’s
side only)
P21W
9
High mounted brake
lamp
LED
a
Tail, parking, standing,
side marker lamp and
brake lamp
LED
b
License plate lamps
C5W
c
Backup lamp
P21W
d
Turn signal lamp
P21W
iVehicles equipped with cornering fog
lamps*:
Front fog lamps use H7 (55 W) lamps.
Warning!
G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

382 Practical hintsReplacing bulbsNotes on bulb replacement

Only use 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:


Additional turn signal lamps in the
exterior rear view mirrors


Bi-Xenon* lamps


Front fog lamps


High mounted brake lamp


Brake lamps


Front and rear side marker lamps


Parking/standing lamps in the tail
lamp assemblies
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 106).

Open the hood (
page 287) (except
for side marker lamps).
iHave the headlamp adjustment
checked regularly.