2005 MERCEDES-BENZ ML500 reset

189 Controls in detail
Useful features
Trip computer*
The trip computer is located in the
overhead console.
1RESET
2MODE
3Display
Switching on the trip computer
Switch on ignition.
Display3 shows one of the available
functions.

If a function display does not appear,
press MODE2.Selecting functions

Press MODE2 repeatedly until the
desired display appears.
The functions are displayed in the
following order:


Date


Compass


Stop watch


Present fuel consumption


Average fuel consumption


Distance remaining


Country


Switching off trip computerSetting the date

Press MODE2 repeatedly until the
date appears.

Press RESET1.
The month shown flashes.

Press MODE2 to advance to selected
month.

Press RESET1.
The day shown flashes.

Press MODE2 to advance to selected
day.

Press RESET1.
The year shown flashes.

Press MODE2 to advance to selected
year.

Press RESET1.
The display stops flashing and the date
is set.
iWith engine not running, the display
switches off automatically 30 seconds
after the last entry.

191 Controls in detail
Useful features
Setting the compass zone
Determine the geographical point of
the vehicle with the aid of the zone
maps.

Switch on the ignition.

Press MODE2 (
page 189) repeat-
edly until the compass display appears
in the trip computer display3.

Press RESET1 (
page 189) to select
the compass zone mode.
The zone selected last is shown in the
display.

Press RESET1 repeatedly until the
correct compass zone, as determined
from the zone map, is shown in the dis-
play.

Press MODE2 twice.
The new compass zone is activated and
the compass display will be shown.Calibrating the compass
If the vehicle was exposed to a significant
magnetic zone, such as high voltage power
lines, the compass may have to be calibrat-
ed.
To calibrate the compass correctly, ob-
serve the following:


Calibrate the compass in an area free
of steel superstructures and power
lines.


Switch off all electrical consumers (e.g.
exterior lamps, climate control, rear
window defroster etc.).


Do not open or close the tilt / sliding
sunroof.


Close doors and liftgate.

Start and run the engine.

Press MODE2 (
page 189) repeat-
edly until the compass display appears
in the trip computer display3.

Press RESET1 and afterwards press
MODE2.
In the display appears
CAL–
.

Press and hold RESET1 for approxi-
mately two seconds.
The calibration mode is activated and
the display shows
CAL
.

Drive without interruption two full cir-
cles at a speed between 3 mph
(5 km / h) and 7 mph (10 km / h).
The message
CAL
goes out after a short
time. The calibration is now complete.
iAn open liftgate triggers the
display
---
.

192 Controls in detailUseful featuresStop watch
Press MODE2 (
page 189) repeat-
edly until the stop watch display ap-
pears in the trip computer display3.
Counting

Press RESET1 (
page 189) to start
counting.Stopping

Press RESET1 again to stop counting.
Resetting

Press and hold RESET1 until the dis-
play shows “0:00”.
Average fuel consumption

Press MODE2 (
page 189) repeat-
edly until the average fuel consumption
display appears in the trip computer
display3.Distance remaining with fuel presently
in tank

Press MODE2 (
page 189) repeat-
edly until the distance remaining dis-
play appears in the trip computer
display3.
iIf CAL
remains in the display, calibration
was not successfully completed. You
have to recalibrate:


Remove the key from the steering
lock.


Start the vehicle and start the cali-
bration procedure described previ-
ously.
We recommend that you have the com-
pass calibrated at a Mercedes-Benz
Light Truck Center.
iWhen the fuel supply drops to reserve
level the display flashes distance re-
maining.

USA only:
The display alternates between FUEL
and distance remaining until
supply is consistently below the re-
serve level. When the fuel supply is
very low (approximately 1.5 gal
[5.5 l])
FUEL
is displayed
continuously.

193 Controls in detail
Useful features
Country
Press MODE2 (
page 189) repeat-
edly until the country display appears
in the trip computer display3.

Press and hold RESET1 a minimum of
five seconds to change the country unit
system.
Canada units system selection
You can choose between CAN-English or
CAN-French.Setting CAN-English

Press RESET1 repeatedly until CAN is
displayed.

Press MODE2 to select
–ENG
.

Press MODE2 again to set CAN-En-
glish.Setting CAN-French

Press RESET1 repeatedly until CAN is
displayed.

Press MODE2.–ENG
is displayed.

Press RESET1 to select
–Fr
.

Press MODE2 to set CAN-French.
The language selected determines how the
various displays are presented, see table.
Display
Language
Date
Cardinal points
Fuel consumption
Distance remaining
GEr
German
DD.MM
Süd, Nord, Ost, West
l / 100 km
Kilometer
Gb
English
MM.DD
South, North, East, West
mi / gal (Imperial)
Miles
ESP
Spain
DD.MM
Sur, Norte, Este, Oeste
l / 100 km
Kilometer
Fr
French
DD.MM
Sud, Nord, Est, Ouest
l / 100 km
Kilometer
USA
American
MM.DD
South, North, East, West
mi / gal (US)
Miles
CAN-ENG
American
MM.DD
South, North, East, West
l / 100 km
Kilometer
CAN-Fr
French
DD.MM
Sud, Nord, Est, Ouest
l / 100 km
Kilometer

238 OperationMaintenanceMaintenance service term exceeded
If you have exceeded the suggested
maintenance service term:

the9 or ½symbol appears in
the display2 for 30 seconds and a
signal sounds after switching on the
ignition.


it is preceded by a “–” (minus symbol).
The Mercedes-Benz Light Truck Center will
reset the maintenance service indicator
following a completed maintenance
service.Calling up the maintenance service
indicator
Within one second press knob1
twice.
The maintenance service indicator dis-
play will appear for ten seconds.Resetting the maintenance service
indicator
In the event that the maintenance service
on your vehicle is not carried out by an au-
thorized Mercedes-Benz Light Truck Cen-
ter, you can reset the maintenance service
indicator yourself.
Switch ignition on and immediately
press knob1 twice within
one second.
The present status for days or distance
is displayed.

Within ten seconds turn the key in
steering lock to position0 (
page 33).

Press and hold knob1 while switch-
ing the ignition on.
The present status for days or distance
is displayed once more.
iIf the battery is disconnected, the days
of disconnection will not be included in
the count shown by the service indica-
tor. To arrive at the true maintenance
service deadline, you will need to sub-
tract these days from the days shown
in the maintenance service indicator.
Do not confuse the maintenance ser-
vice indicator with the engine oil level
indicator:.

239 Operation
Maintenance

Continue to hold knob1.
After approximately ten seconds a sig-
nal sounds, and the display shows the
distance to the next maintenance ser-
vice due for approximately
ten seconds.

Release knob1.iIf the maintenance service indicator
was inadvertently reset, have a
Mercedes-Benz Light Truck Center cor-
rect it.
Only reset if the proper maintenance
service has been performed. Resetting
the system without performing the
proper service as called for by the
maintenance service indicator will re-
sult in engine damage and / or other ve-
hicle damage not covered by the
Mercedes-Benz Limited Warranty.

344 IndexRemote control
Global locking 89
Global unlocking 89
Replacing batteries 273
Synchronizing 273
Unlocking liftgate 89
Unlocking the driver’s door,
fuel filler flap 89
Unlocking with 32
Remote control with folding key 88
Remote door unlock
With Tele Aid* 182
Remote Vehicle Diagnostics 326
Removing
Vehicle battery 289
Wheel 286
Wiper blades 283
Removing spare wheel 266Replacing
Backup lamp bulbs 279
Brake lamp bulbs 279
Bulbs 274
Front lamp bulbs 276
Front turn signal bulbs 278
Fuses 298
High beam halogen bulbs 277
High mounted brake lamp 281
License plate lamp bulbs 281
Low beam bulbs 276
Rear fog lamp bulbs 279
Rear lamp bulbs 275, 279
Rear side marker lamp bulbs 279
Rear turn signal bulbs 279
Side marker bulb 278
Wiper blades 283
Replacing front fog lamp bulb 279
Reporting
Safety defects 19
Resetting
Service indicator (FSS) 238
Trip odometer 119
Residual heat utilization 142, 326
Residual ventilation 142REST (Residual engine heat
utilization) 326
Restraint system 326
Restraint system see Infant and child
restraint systems
Returning from off-road driving 210
Rims 307
Roadside assistance 12
Tele Aid* 178
RON 220
RON (Research Octane Number) 326
Roof rack 166
Rotating wheels 233
Rubber parts
Cleaning 245
S
Safety
Occupant 58
Safety belts see Seat belts
Safety defects
Reporting 19
Safety systems
Driving 76

349 Index
Trip computer* 29, 189
Average fuel consumption 192
Compass 190
Country 193
Distance remaining 192
Language 193
Selecting functions 189
Setting date 189
Stop watch 192
Switching on 189
Trip odometer
Resetting 119
Trip odometer display 118
Trunk see Cargo compartment
Turn signal lamps
Replacing bulbs 274, 275
Turn signal, side marker lamp
Replacing bulbs 274
Turn signals 50
Additional in mirrors 274
Cleaning lenses 242
Front bulbs 274
Indicator lamps 25
Rear bulbs 275, 279Turning off
Engine 55
TWR (Tongue Weight Rating) 327
U
Unlocking 32, 88
Centrally from inside 94
Driver’s door in an emergency 268
Driver’s door, fuel filler flap 89
Fuel filler flap 219
In an emergency 268
Transmission selector lever
manually 270
Vehicle in an emergency 182
With the remote control 32
Upgrade signals
Tele Aid* 181
Uphill driving
Cruise control 154
Upholstery
Cleaning 245
Upshifting 121Useful features 167
Ashtrays and cigarette lighter 171
Cup holder 169
Electrical outlet 173
Garage door opener 183
Storage compartments 167
Tele Aid* 174
Telephone* 173
Trip computer* 189
V
Vehicle
Data recording 20
Locking 28
Locking in an emergency 269
Lowering 287
Proper use of 17
Service battery 272
Towing 293
Unlocking 28
Unlocking in an emergency 268
Vehicle and trailer weights and
ratings 212
Vehicle battery 272