2005 MERCEDES-BENZ E55AMG remote control

280 Controls in detailUseful featuresWarning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure that people and objects
are out of the way of the device to prevent
potential harm or damage. When program-
ming a garage door opener, the door moves
up or down. When programming a gate oper-
ator, the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.
iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact an authorized
Mercedes-Benz Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.

281 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on the ignition (
page 33).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons1 and3 and release
them only when the indicator lamp4
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp4 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (1, 2
or3). Do not release the buttons until
completing step 5.
The indicator lamp4 on the integrat-
ed remote control will flash, first slowly
and then rapidly.
iCanada only:
This device complies with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions:
(1) This device may not cause interfer-
ence, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation of the device.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.


283 Controls in detail
Useful features
Step 9:
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (1, 2
or3).
Step 11:

Press, hold for two seconds and re-
lease same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.Step 12:

Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (1, 2
or3).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Continue to press and hold the inte-
grated signal transmitter button (1,
2 or3) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp4 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.

284 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 33).

Select and press the appropriate inte-
grated signal transmitter button (1,
2 or3) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory

Switch on the ignition (
page 33).

Simultaneously hold down the signal
transmitter buttons1 and 3, for ap-
proximately 20 seconds, until the indi-
cator lamp4 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (1, 2 or3). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

299 Operation
At the gas station
At the gas station
Refueling
The fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking / unlocking the vehicle with
the remote control automatically
locks / unlocks the fuel filler flap.

Turn the engine off

by turning the SmartKey to
position0.


by pressing the KEYLESS-GO*
start/stop button. Open the driv-
er’s door (with the driver’s door
open, starter switch is now in
position0, same as SmartKey re-
moved from starter switch).

Remove the SmartKey from the starter
switch.

Open the fuel filler flap by pushing at
the point indicated by the arrow.
The fuel filler flap springs open.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in the recess
on the fuel filler flap.
To prevent fuel vapors from escaping
into open air, fully insert filler nozzle
unit.

Only fill your tank until the filler nozzle
unit cuts out – do not top up or over-
fill.
Warning!
G
Gasoline and diesel fuel are highly flamma-
ble and poisonous. They burn violently and
can cause serious injury. Whenever you are
around gasoline or diesel fuel, avoid inhaling
fumes and skin contact, extinguish all smok-
ing materials. Never allow sparks, flame or
smoking materials near gasoline or diesel
fuel!
!Diesel engine:
When filling the diesel fuel tank using
fuel containers, place a filling filter, a
suede cloth or a clean flannel cloth into
the filler neck to filter the diesel fuel.
Otherwise, you could clog the fuel
lines.


485 Index
Emergency operations
Opening/closing sliding/pop-up roof*
or panorama sliding/pop-up
roof* 414
Releasing trunk lid from inside 117
Remote door unlock 278
Unlocking the trunk lid 411
Unlocking the vehicle 410
Emergency tensioning device see
ETD 70, 472
Emission control 297
Ending
A call (telephone) 172
Engine 450
Compartment 303
Message in the display 359, 360,
383
Starting 46
Starting with KEYLESS-GO* 47
Starting with the SmartKey 46, 47
Turning off with the key 56
Engine compartment
Hood 303
Engine malfunction indicator lamp 359,
360, 383
Engine number 472Engine oil
Adding 306
Checking level 304
Consumption 304
Display messages 387
Messages in display 305
Viscosity 472
ESP 87, 472
Four wheel electronic traction system
with ESP 93
Switching off 89
Switching on 90
Synchronizing 372
Warning lamp 357
ETD 472
Safety guidelines 64
Exterior lamp switch 133
Exterior rear view mirrors
Adjusting 41
Parking position for 168F
Fahrenheit
Setting temperature units 157
Fastening the seat belts 43
Fine adjustment
Cruise control 234
First aid kit 407
Flat tire 425
Collapsible tire 429
Mounting the spare wheel 425, 428
Spare wheel 425
Flexible Service System (Canada
vehicles) 343
Flexible Service System (FSS) 473
Fog lamp, rear 137
Fog lamps, front
Messages in display 392
Switching on 136
Following distance in Distronic* 242
Four wheel electronic traction system
(4MATIC) with ESP 93
4MATIC 93

486 IndexFront airbags 65
Front fog lamp
Replacing bulb 418
Front lamps 418
Messages in display 394
Replacing bulbs 420
Switching on 133
Front seat head restraints
Power seat 123
Removing and installing 123
Front seats
Heater* 127
FSS (Canada vehicles) 343
FSS (Flexible Service System) 473
Fuel 300
Fuel tank reserve warning lamp 362
Premium unleaded gasoline 300
Fuel consumption statistics
After start 170
Since last reset 170Fuel filler flap 299
Locking 299
Unlocking 299
Fuel requirements 466
Fuel reserve tank
Message in display 389
Fuel tank
Filler flap 299
Fuels, coolants, lubricants etc. 461
Functions (control system) 149
Resetting 155
Fuse chart 443
Fuses 443
Fuse chart 443
Fuse extractor 443
Spare fuses 443G
Garage door opener 29, 279
Erasing the integrated remote
control 284
Integrated remote control 281
Rolling code programming 282
Gasoline see Fuel 300
GAWR 337
Gear range 473
Automatic transmission 177
Limiting 177
Shifting into optimal 176
Gear range limit
Canceling 176
Gear selector lever
Position 178
Global
Locking 100
Locking with KEYLESS-GO* 105
Unlocking 99
Unlocking with KEYLESS-GO* 105
Global Positioning System (GPS) 473
Glove box 262
Closing 262
Opening 262

487 Index
Good visibility 186
GPS 473
GPS see COMAND 272
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GVW 337
GVWR 338
H
Hand-held transmitter
Programming integrated remote
control 281
Reprogramming integrated remote
control 284
Hazard warning flasher 138
Switching off 138
Switching on 138Headlamps
Automatic control 134
Bi-Xenon* 471
Cleaning system* 186
Switching off 56
Switching on 50
Heated seats* 127
Heated steering wheel* 270
Heater booster system 203, 473
Height adjustment
Head restraints 39
Steering wheel 39
Vehicle level 248
High beam flasher 50, 137
High beam headlamps
Messages in display 394
Replacing bulbs 418
Switching on 50, 137
High mounted brake lamp 418
Hood 303
Closing 303
Message in display 389
Opening 303
Hydroplaning 291I
Identification labels 448
Ignition 34, 36
Switching on 46, 47
Immobilizer 94
Activating 94
Deactivating 94
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems 71
Installing 80
LATCH child seat anchors 81
Information
About service and warranty 10
Button for Tele Aid* 276
Inside rear view mirror
Antiglare 186
Installing
Infant and child restraint systems 80
Towing eye bolt 442
Wiper blades 424