2005 MERCEDES-BENZ E55AMG low beam

137 Controls in detail
Lighting
Rear fog lamp (driver’s side only)
Switch on the low beam headlamps
(page 50).

Pull out exterior lamp switch to second
stop.
The yellow indicator lamp† in the
exterior lamp switch comes on
(page 133).

Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The yellow indicator lamp† in the
exterior lamp switch goes out.
The front fog lamps remain lit.
Combination switch
The combination switch is located on the
left side of the steering column.Combination switch1High beam
2High beam flasherHigh beam

Turn the exterior lamp switch to
positionB orU (
page 133).

Push the combination switch in direc-
tion of arrow1 to switch on the high
beam.
The high beam headlamp indicator
lampA in the instrument cluster
comes on (
page 24).

Pull the combination switch in direction
of arrow2 to its original position to
switch off the high beam.
The high beam headlamp indicator
lampA in the instrument cluster
goes out.
High beam flasher

Pull the combination switch briefly in
direction of arrow2.

162 Controls in detailControl systemLighting submenu
Access the
Lighting
submenu via the
Set-
tings
menu. Use the
Lighting
submenu
to change the lamp and lighting settings on
your vehicle. The following functions are
available:Setting daytime running lamp mode
(USA only)

Move the selection marker with
buttonæ orç to the
Lighting

submenu.

Press buttonj ork repeatedly
until you see
Lamp circuit headlamp
in
the multifunction display.
The selection marker is on the current
setting.

Press buttonæ orç to select
manual operation (
manual
) or daytime
running lamp mode (
constant
) activat-
ed.
With daytime running lamp mode activated
and the exterior lamp switch at
positionM orU the low beam head-
lamps are switched on when the engine is
running.
In low ambient light conditions the follow-
ing lamps will switch on additionally:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps
For more information on the daytime run-
ning lamp mode, see “Lighting”
(
page 133).
Function
Page
Set daytime running lamp mode
(USA only)
162
Setting locator lighting
163
Setting night security illumina-
tion
164
Setting interior lighting delayed
shut-off
165
Setting ambient lighting
165
iThis function is not available in coun-
tries where the daytime running lamp
mode is mandatory and therefore in a
constant mode.

368 Practical hintsWhat to do if …On the pages that follow, you will find a
compilation of the most important warning
and malfunction messages that may ap-
pear in the multifunction display.
For your convenience the messages are di-
vided into two sections:

Text messages (
page 369)


Symbol messages (
page 378)
iSwitching on the ignition causes all in-
strument cluster lamps (except low
beam headlamp indicator lamp, high
beam headlamp indicator lamp, and
turn signal indicator lamps unless acti-
vated) as well as the multifunction dis-
play to come on. Make sure the lamps
and multifunction display are in work-
ing order before starting your journey.

393 Practical hints
What to do if …
Display symbol
Display messages
Possible cause
Possible solution
.
Low beam,
right
The right low beam lamp is malfunction-
ing.
Halogen headlamp:
Replace the bulb as soon as possible.
Bi-Xenon* headlamp:

Visit an authorized Mercedes-Benz
Center as soon as possible.
Front Marker light
,
left
The front left side marker lamp is mal-
functioning.

Replace the bulb as soon as possible.
Front Marker light
right
The front right side marker lamp is mal-
functioning.

Replace the bulb as soon as possible.
Fr. Park. lamp, left
The left parking lamps are malfunction-
ing.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Fr. Park. lamp, right
The right parking lamps are malfunction-
ing.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Rear foglamp
Substitute bulb on
The rear fog lamp is malfunctioning. A
substitute bulb is being used.

Replace the bulb as soon as possible.
Backup lamp, left
The left reverse lamp is malfunctioning.

Replace the bulb as soon as possible.
Backup lamp, right
The right reverse lamp is malfunctioning.

Replace the bulb as soon as possible.
Switch off lamps
Lamps have been turned on although the
SmartKey in the starter switch is in posi-
tion 0.

Switch off the headlights.

394 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause
Possible solution
.
High beam,
left
The left high beam lamp is malfunction-
ing.

Replace the bulb as soon as possible.
High beam,
right
The right high beam lamp is malfunction-
ing.

Replace the bulb as soon as possible.
License plate lamp,
left
The left license plate lamp is malfunction-
ing.

Replace the bulb as soon as possible.
License plate lamp,
right

The right license plate lamp is malfunc-
tioning.

Replace the bulb as soon as possible.
Light sensor
Drive to workshop
The lamp sensor is malfunctioning. The
headlamps switch on automatically.

In the control system, set lamp opera-
tion to manual mode (
page 162).

Switch on headlamps using the exteri-
or lamp switch.
Low beam,
left
The left low beam lamp is malfunctioning.
Halogen headlamp:
Replace the bulb as soon as possible.
Bi-Xenon* headlamp:

Visit an authorized Mercedes-Benz
Center as soon as possible.

418 Practical hintsReplacing bulbs
Front lamps Rear lamps
Lamp
Type
1
Additional turn signal
lamps
LED
2
Turn signal lamp
1156 NA
3
Side marker lamp
W 5 W
4
Halogen headlamps:
Low beam
Bi-Xenon* headlamps:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Bi-Xenon bulbs yourself. See your
authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35 W
5
Halogen headlamps:
High beam/high beam
flasher
Bi-Xenon* headlamps:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lamps
W 5 W
6
Front fog lamp
HB4 (51 W)
Lamp
Type
7
High mounted brake
lamp
LED
8
Brake, tail, parking,
standing, backup lamps
and turn signal lamps.
Rear fog lamp (only
driver’s side)
HiP
LED*
9
License plate lamps
C5W

420 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Bulb socket for high beam head-
lamp/high beam flasher bulb
2Bulb socket for parking and standing
lamp bulb
3Housing cover for low
beam/Bi-Xenon* headlamp4Bulb socket for turn signal lamp bulb
5Electrical connector for high beam
headlamp/high beam flasher bulb
6Bulb socket for parking and standing
lamp bulb
7Electrical connector for low beam
headlamp bulb (halogen headlamps
only)
Before you start to replace a bulb for a
front lamp, do the following first:

Turn the exterior lamp switch to
positionM (
page 133).

Open the hood (
page 303) (except
for side marker lamps).
Warning!
G
Do not remove the cover3 for the Bi-Xe-
non* headlamp. Because of high voltage in
Xenon* lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.

421 Practical hints
Replacing bulbs
Low beam bulb (halogen headlamps
only)
Turn housing cover3 counterclock-
wise and remove it.

Pull electrical connector7 off.

Unclip the retainer spring on the bulb
socket and take out the bulb.

Insert the new bulb so that its base lo-
cates in the recess on the lower left
and is level to it.

Clip on the retainer spring.

Plug electrical connector7 onto the
bulb.

Align housing cover3 and turn it
clockwise.
High beam bulb/high beam flasher
bulb (halogen headlamps)/high beam
flasher bulb (Bi-Xenon* headlamps)

Turn bulb socket1 with the bulb
counterclockwise and remove it.

Pull electrical connector5 off.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.

Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.

Plug electrical connector5 onto the
bulb.

Place bulb socket1 back into the
lamp and turn it clockwise.
Front turn signal lamp bulb

Turn bulb socket4 with the bulb
counterclockwise and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket4.

Press the new bulb gently into bulb
socket4 and turn clockwise until it
engages.

Place bulb socket4 back into the
lamp and turn it clockwise.Parking and standing lamp bulb

Pull out bulb socket6 with the bulb.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket6.

Press the new bulb gently into bulb
socket6 and turn clockwise until it
engages.

Press bulb socket6 back into the
lamp.