2005 MERCEDES-BENZ E55AMG bulb

417 Practical hints
Replacing bulbs
Replacing bulbs
Bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
iIf the headlamps or front fog lamps are
fogged up on the inside as a result of
high humidity, driving the vehicle a dis-
tance with the lights on should clear up
the fogging.
iSubstitute bulbs will be brought into
use when lamps malfunction. Observe
the messages in the multifunction dis-
play (
page 392).

418 Practical hintsReplacing bulbs
Front lamps Rear lamps
Lamp
Type
1
Additional turn signal
lamps
LED
2
Turn signal lamp
1156 NA
3
Side marker lamp
W 5 W
4
Halogen headlamps:
Low beam
Bi-Xenon* headlamps:
Low and high beam
1
1Vehicles with Bi-Xenon* headlamps: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Bi-Xenon bulbs yourself. See your
authorized Mercedes-Benz Center.
H7 (55 W)
D2S-35 W
5
Halogen headlamps:
High beam/high beam
flasher
Bi-Xenon* headlamps:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lamps
W 5 W
6
Front fog lamp
HB4 (51 W)
Lamp
Type
7
High mounted brake
lamp
LED
8
Brake, tail, parking,
standing, backup lamps
and turn signal lamps.
Rear fog lamp (only
driver’s side)
HiP
LED*
9
License plate lamps
C5W

419 Practical hints
Replacing bulbs
Notes on bulb replacement

Use only 12 volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:


Additional turn signals in the exterior
rear view mirrors


High mounted brake lamp


Xenon* lamps


Front fog lamps


Rear lamps (except license plate
lamps)
Warning!
G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas.
A bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
iHave the headlamp adjustment
checked regularly.

420 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Bulb socket for high beam head-
lamp/high beam flasher bulb
2Bulb socket for parking and standing
lamp bulb
3Housing cover for low
beam/Bi-Xenon* headlamp4Bulb socket for turn signal lamp bulb
5Electrical connector for high beam
headlamp/high beam flasher bulb
6Bulb socket for parking and standing
lamp bulb
7Electrical connector for low beam
headlamp bulb (halogen headlamps
only)
Before you start to replace a bulb for a
front lamp, do the following first:

Turn the exterior lamp switch to
positionM (
page 133).

Open the hood (
page 303) (except
for side marker lamps).
Warning!
G
Do not remove the cover3 for the Bi-Xe-
non* headlamp. Because of high voltage in
Xenon* lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.

421 Practical hints
Replacing bulbs
Low beam bulb (halogen headlamps
only)
Turn housing cover3 counterclock-
wise and remove it.

Pull electrical connector7 off.

Unclip the retainer spring on the bulb
socket and take out the bulb.

Insert the new bulb so that its base lo-
cates in the recess on the lower left
and is level to it.

Clip on the retainer spring.

Plug electrical connector7 onto the
bulb.

Align housing cover3 and turn it
clockwise.
High beam bulb/high beam flasher
bulb (halogen headlamps)/high beam
flasher bulb (Bi-Xenon* headlamps)

Turn bulb socket1 with the bulb
counterclockwise and remove it.

Pull electrical connector5 off.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.

Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.

Plug electrical connector5 onto the
bulb.

Place bulb socket1 back into the
lamp and turn it clockwise.
Front turn signal lamp bulb

Turn bulb socket4 with the bulb
counterclockwise and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket4.

Press the new bulb gently into bulb
socket4 and turn clockwise until it
engages.

Place bulb socket4 back into the
lamp and turn it clockwise.Parking and standing lamp bulb

Pull out bulb socket6 with the bulb.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket6.

Press the new bulb gently into bulb
socket6 and turn clockwise until it
engages.

Press bulb socket6 back into the
lamp.

422 Practical hintsReplacing bulbsSide marker lamp bulb
Carefully slide the lamp towards the
front in direction of arrows.

Remove the rear end first.

Turn the bulb socket with the bulb
counterclockwise and remove it.

Pull the bulb out of the bulb socket.

Insert the new bulb into the bulb sock-
et.

Place the bulb socket back into the
lamp and turn it clockwise.

To reinstall the lamp, set the front end
in the bumper and let the rear end en-
gage.
Replacing bulbs for rear lamps
Tail lamp unit
The tail lamps are equipped with HiP bulbs.License plate lamp
1Screw

Turn the exterior lamp switch to
positionM (
page 133).

Loosen both screws1.

Remove the license plate lamp.

Replace the bulb.

Reinstall the license plate lamp.

Retighten screws1.
Warning!
G
The bulbs in the tail lamps cannot be re-
placed individually. The tail lamp bulbs are
under pressure and could explode during an
attempt to replace them.
If the tail lamps are malfunctioning, have
them exchanged at an authorized
Mercedes-Benz Center.

480 IndexBattery discharged
Jump starting 436
Bead 337
Bi-Xenon headlamps* 471
Bleeding the fuel system 432
Block heater* 342
Blocking
Rear window operation 83
Brake assist system (BAS) 471
Brake fluid 301, 382
Brake pads
Message in display 380
Brakes
Warning lamp 358
Break-in period 286Bulbs, replacing
Additional turn signals 417
Fog lamps 417
Front lamps 417, 420
High beam 418
High mounted brake lamp 418
License plate lamps 418, 422
Low beam 418
Parking lamps 418
Side marker lamps 417, 422
Standing lamps 418
Tail lamp 418
Tail lamp assemblies 422
Turn signal lamp 417
C
CAC (Customer Assistance Center) 471
Calling up
Distronic* settings 152
Maintenance service indicator 345
Range (distance to empty) 171
CAN system 471
Cargo tie-down rings 261
CD player
Operating 151Center console
Lower part 28
PASS AIR BAG OFF indicator
lamp 365
Upper part 27
Centigrade
Setting temperature units 157
Central locking
From inside 119
Switch 119
Switching on/off (control
system) 166
Unlocking from inside 119
Central locking switch 119
Changing
Batteries (SmartKey with
KEYLESS-GO*) 415, 416
Batteries (SmartKey) 415, 416
SmartKey setting 167
Vehicle level 249
Charging
Vehicle batteries 435
CHECK ENGINE malfunction indicator
lamp 359, 360

486 IndexFront airbags 65
Front fog lamp
Replacing bulb 418
Front lamps 418
Messages in display 394
Replacing bulbs 420
Switching on 133
Front seat head restraints
Power seat 123
Removing and installing 123
Front seats
Heater* 127
FSS (Canada vehicles) 343
FSS (Flexible Service System) 473
Fuel 300
Fuel tank reserve warning lamp 362
Premium unleaded gasoline 300
Fuel consumption statistics
After start 170
Since last reset 170Fuel filler flap 299
Locking 299
Unlocking 299
Fuel requirements 466
Fuel reserve tank
Message in display 389
Fuel tank
Filler flap 299
Fuels, coolants, lubricants etc. 461
Functions (control system) 149
Resetting 155
Fuse chart 443
Fuses 443
Fuse chart 443
Fuse extractor 443
Spare fuses 443G
Garage door opener 29, 279
Erasing the integrated remote
control 284
Integrated remote control 281
Rolling code programming 282
Gasoline see Fuel 300
GAWR 337
Gear range 473
Automatic transmission 177
Limiting 177
Shifting into optimal 176
Gear range limit
Canceling 176
Gear selector lever
Position 178
Global
Locking 100
Locking with KEYLESS-GO* 105
Unlocking 99
Unlocking with KEYLESS-GO* 105
Global Positioning System (GPS) 473
Glove box 262
Closing 262
Opening 262