2005 MERCEDES-BENZ E WAGON ignition

282 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 34).

Select and press the appropriate inte-
grated signal transmitter button (1,
2 or3) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory

Switch on the ignition (
page 34).

Simultaneously hold down the signal
transmitter buttons1 and 3, for ap-
proximately 20 seconds, until the indi-
cator lamp4 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (1, 2 or3). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.iIf you sell your vehicle, erase the codes
of all three channels.

300 OperationEngine compartment
Closing
Let the hood drop from a height of ap-
proximately 1 ft (30 cm).
The hood will lock audibly.

Check to make sure the hood is fully
closed.
If you can raise the hood at a point
above the headlamps, then it is not
properly closed. Open it again and let it
drop with somewhat greater force.
Engine oil
The amount of oil your engine needs will
depend on a number of factors, including
driving style. Higher oil consumption can
occur when

the vehicle is new


the vehicle is driven frequently at
higher engine speeds
Engine oil consumption checks should only
be made after the vehicle break-in period.
Warning!
G
If you see flames or smoke coming from the
engine compartment, or if the coolant tem-
perature gauge indicates that the engine is
overheated, do not open the hood. Move
away from vehicle and do not open the hood
until the engine has cooled. If necessary,
call the fire department.Warning!
G
The engine is equipped with a transistorized
ignition system. Because of the high voltage
it is dangerous to touch any components (ig-
nition coils, spark plug sockets, diagnostic
socket) of the ignition system

with the engine running


while starting the engine


if ignition is “on” and the engine is
turned manually
Warning!
G
Be careful that you do not close the hood on
anyone.
iDo not use any special lubricant addi-
tives, as these may damage the drive
assemblies. Using special additives not
approved by Mercedes-Benz may
cause damage not covered by the
Mercedes-Benz Limited Warranty.
More information on this subject is
available at any Mercedes-Benz
Center.

301 Operation
Engine compartment
Checking engine oil level with the
control system
When checking the oil level

the vehicle must be parked on level
ground


with the engine at operating tempera-
ture, the vehicle must have been sta-
tionary for at least five minutes with the
engine turned off


with the engine not at operating tem-
perature yet, the vehicle must have
been stationary for at least 30 minutes
with the engine turned off
To check the engine oil level via the multi-
function display, do the following:

Switch on the ignition (
page 34).
The standard display (
page 153) should
appear in the multifunction display.

Press button k or j, on the
steering wheel until the following
message is seen in the multifunction
display:
Engine oil level - Measuring now!
Measurement correct only if veh.
levelOne of the following messages will
subsequently appear in the indicator:

Engine oil level ok


Add 1.0 Qt. to reach max. oil
level(Canada:
1.0 Liter
)


Add 1.5 Qts. to reach max. oil
level(Canada:
1.5 Liters
)


Add 2.0 Qts. to reach max. oil
level(Canada:
2.0 Liters
)

If necessary, add engine oil.
For adding engine oil, see (
page 302).
More information on engine oil can be
found in the “Technical data” section
(
page 450) and (
page 453).
Other display messages
If the SmartKey or KEYLESS-GO start/stop
button* is not in position 2, the following
message will appear:
Switch on ignition
to check engine oil level
Switch on the ignition (
page 34).
iIf you want to interrupt the checking
procedure, press thek orj
button on the multifunction steering
wheel.

319 Operation
Tires and wheels

Switch on the ignition (
page 34).

Press buttonè orÿ on the mul-
tifunction steering wheel repeatedly
until the standard display menu ap-
pears in the multifunction display
(page 158).

Press the j or k button until the
current inflation pressures for each tire
appear in the multifunction display.iPossible differences between the read-
ings of a tire inflation pressure gauge of
an air hose, e.g. gas station equipment,
and the vehicle’s control system can
occur. The readings issued by the con-
trol system are more precise.
Warning!
G
When the tire pressure monitoring system*
warning light is lit, one or more of your tires
is significantly under-inflated. You should
stop and check your tires as soon as possi-
ble, and inflate them to the proper pressure
as indicated on the vehicle’s tire information
placard. Driving on a significantly under-in-
flated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability. Each tire, including the
spare, should be checked monthly when
cold and set to the recommended inflation
pressure as specified in the vehicle placard
and Operator’s Manual.iThe recommended tire inflation pres-
sures for your vehicle can be found on
the placard of the driver’s door B-pillar
or the inside of the fuel filler flap, not in
the Operator’s Manual.
Warning!
G
The tire pressure monitoring system* does
not indicate a warning for wrongly selected
inflation pressures. Always adjust tire infla-
tion pressure according to the placard of the
driver’s door B-pillar or the inside of the fuel
filler flap.
The tire pressure monitoring system* is not
able to issue a warning due to a sudden dra-
matic loss of pressure (e.g. tire blowout
caused by a foreign object). In this case
bring the vehicle to a halt by carefully apply-
ing the brakes and avoiding abrupt steering
maneuvers.iOperating radio transmission equip-
ment (e.g. wireless headsets, two-way
radios) in or near the vehicle could
cause the tire pressure monitoring sys-
tem* to malfunction.

339 Operation
Maintenance
Maintenance
We strongly recommend that you have
your vehicle serviced by an authorized
Mercedes-Benz Center, in accordance with
the Maintenance Booklet at the times
called for by the maintenance service indi-
cator display.
Failure to have the vehicle maintained in
accordance with the Maintenance Booklet
and maintenance service indicator at the
designated times /mileage will result in ve-
hicle damage not covered by the
Mercedes-Benz Limited Warranty.
The maintenance service indicator will no-
tify you when your next maintenance ser-
vice is due.
Starting approximately one month before
maintenance service is due, one of the fol-
lowing messages will appear in the multi-
function display while you are driving or
when you switch on the ignition (example
service A):
Service A in XXXX miles (km)
Service A in XX days
Service A in X day
Service A due now!The maintenance services will be indicated
by showing a service type A through type H
in the multifunction display. Types A
through H are classified based on estimat-
ed time needed to perform the mainte-
nance service, ranging:
from
Service A(approx. one hour)
toService H(approx. eight hours)When the service type appears, you can
use the vehicle’s control system to view a
list of the service items (1-14) that need to
be performed at the called for service type
(
page 343).iThe additional + after the type of ser-
vice indicates the degree of wear of the
brake pads.
The brake pads may reach their wear
limit in the time period up to the next
service interval.
Have the brake pads checked and, if
necessary, replaced by an authorized
Mercedes-Benz Center during your
next service appointment.

341 Operation
Maintenance
Calling up the maintenance service indicator
Switch on the ignition (
page 34).
The standard display of the control sys-
tem appears (
page 153).

Press button k or j on the mul-
tifunction steering wheel until the
maintenance service indicator with the
service symbol 9 or ´ and the
service deadline appears in the multi-
function display.Resetting the maintenance service
indicator
In the event that the maintenance service
on your vehicle is not carried out by an au-
thorized Mercedes-Benz Center, you can
have the maintenance service indicator re-
set. The automotive maintenance facility
carrying out the maintenance service will
find the information for resetting the main-
tenance service indicator in the mainte-
nance-relevant information for your
vehicle. Such information is available from
either your authorized Mercedes-Benz
Center or directly from Mercedes-Benz.
iIf the battery is disconnected, the days
of disconnection will not be included in
the count shown by the maintenance
service indicator. To arrive at the true
maintenance service deadline, you will
need to subtract these days from the
days shown in the maintenance service
indicator.
Do not confuse the maintenance ser-
vice indicator with the engine oil level
indicator :.
iIf the maintenance service indicator
was inadvertently reset, have an autho-
rized Mercedes-Benz Center correct it.
Only reset if the proper maintenance
service has been performed. Resetting
the system without performing the
proper service as called for by the
maintenance service indicator will re-
sult in engine damage and/or other ve-
hicle damage not covered by the
Mercedes-Benz Limited Warranty.

342 OperationMaintenanceSetting the date for special works
You can enter appointments for exhaust
gas analysis and general inspection using
the maintenance system.
Switch on the ignition (
page 34).
The standard display of the control sys-
tem appears (
page 153).

Press buttonk orj on the mul-
tifunction steering wheel until the
maintenance indicator appears in the
multifunction display.

Press the reset button (
page 24) for
about five seconds.
The
Service menu
appears in the multi-
function display.

Select the
Addit. Work
menu with the
+ or - button.

Press the ÿ button.
The service indicator now displays the Addit. Work
menu.

Select the
Exh.-gas analysis
or
General inspection
menu with the
+ or - button.

Press the ÿ button.
The service indicator now displays the Next due date
menu.

Select the
Month a
nd
Year
with the
+ or - button.

Press buttonk orj on the mul-
tifunction steering wheel to set the
month and year.

Select
Confirm
with the + or -
button.

Press the ÿ button.
The new date is set.

343 Operation
Maintenance

Press theè button on the multi-
function steering wheel until the stan-
dard display appears in the
multifunction display.
The maintenance service system now re-
calculates the values. You cannot call up
the service display or the service menu
during this time.
Calling up the maintenance service
data information
The maintenance service indicator shows
the maintenance service type (letters A-H)
in the multifunction display approximately
one month before the service appointment
is due in miles (distance criterion) or in
days (time criterion).
This maintenance service type is based on
the service items to be carried out. The
service items are described in the Mainte-
nance Booklet.
The service items to be carried out under
the corresponding service type can be dis-
played in the multifunction display.Calling up the service item menu

Switch on the ignition (
page 34).
The standard display of the control sys-
tem appears (
page 153).

Press buttonk orj on the mul-
tifunction steering wheel until the
maintenance service indicator appears
in the multifunction display.

Press the reset button (
page 24) for
about five seconds.
The
Service menu
appears in the multi-
function display (page 153).

Select the
Items
menu with the +
or - button.

Press the ÿ button.The service indicator now displays the
Items
menu.

Press buttonè on the multifunction
steering wheel until the standard
display appears in the multifunction
display.iThe service items to be carried out are
shown in this menu.
Please refer to the Maintenance Book-
let for a description of each service
item.