2005 MERCEDES-BENZ CL500 mirror controls

251 Controls in detail
Useful features
Garage door opener
The built-in remote control is capable of
operating up to three separately controlled
devices, for example garage door openers,
gate openers, or other devices compatible
with HomeLink
® or some other systems.
You can program the signal transmitter
buttons.
Remote control integrated into the interior
rear view mirror1Indicator lamp
2 3 4Signal transmitter button
5Hand-held transmitter button
6Hand-held remote control trans-
mitter (not part of the vehicle
equipment)
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage.
When programming a garage door opener,
the door moves up or down. When program-
ming a gate operator, the gate opens or
closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.

253 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition (
page 34).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and 4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 cm to 12 cm) away from the sur-
face of the integrated remote control
located on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp 1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.

437 Index
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems 72
Installing 76
LATCH child seat mounts 77
Information
About service and warranty 10
Button for Tele Aid* 246
Inside rear view mirror
Auto-dimming 178
Installing
Infant and child restraint systems 76
Wiper blades 380
Instrument cluster 23, 24, 133, 421
Cleaning 322
Coolant temperature gauge 134
Illumination 133
Multifunction display 136
Outside temperature indicator 135
Selecting language 157
Instruments and controls see Cockpit 22Integrated remote control
Canadian programming 254
Erasing memory 255
Hand-held transmitter 252
Operating 255
Rolling code programming 253
Interior illumination
Delayed switch-off 160
Interior lighting 130
Activating automatic control 130
Deactivating automatic control 131
Manual operation 131
Reading lamps 131
Interior rear view mirror
Adjusting 43
J
Jump starting 389K
Key, mechanical 367
Key, SmartKey
Loss of 94
Remote control 90
Restoring to factory setting 93
Starting the engine 48
Turning off the engine 59
Unlocking with 32
Key, SmartKey with KEYLESS-GO*
Remote control 94
Key, SmartKey, SmartKey with KEY-
LESS-GO*
Replacing the battery 371
Key-dependency memory
Settings 162
KEYLESS-GO* 421
Activating ignition with 36
Locking the vehicle 99
Messages in display 350
Starting the engine 49
Turning off engine 59

444 IndexReading lamps 131
Rear fog lamp 374
Bulb 374
Switching on 128
Rear lamp bulbs
Replacing 377
Rear lamps see Tail lamps
Rear passenger compartment
Adjustable air vents 196
Rear seat head restraints
Folding back with switch 115
Placing upright 115
Rear seats
Head restraints 115
Rear view mirror 29
Rear view mirror auto-dimming 178
Rear view mirrors see Mirrors
Rear window
Blocking operation 78Rear window defroster 193
Activating 193
Deactivating 193
Rear window sunshade* 183
Recommended inflation pressure 310
Reconnecting
Vehicle battery 388
Recovery services
For stolen vehicle 249
Refueling 270
Regular checks 271
Regular driving style 220
Reinstalling vehicle battery 387
Remote control
SmartKey 90
SmartKey with KEYLESS-GO* 94
Remote controls
Integrated 252
Remote door unlock
With Tele Aid 249Removing
Vehicle battery 387
Wheel 384
Wiper blades 379
Replacing
Backup lamp bulbs 377
Battery (SmartKey with
KEYLESS-GO*) 372
Brake lamp bulbs 377
Bulbs 373
Front lamp bulbs 376
License plate lamp bulbs 378
Parking lamp bulbs 377
Rear fog lamp bulbs 377, 378
Rear lamp bulbs 374, 377
Rear turn signal bulbs 377
Side marker lamp bulbs 377
Standing lamp bulbs 377
Wiper blades 379
Reporting
Safety defects 18