2005 MERCEDES-BENZ CL-Class key

89 Telephone*
Important notes
iIf you have a Mercedes-Benz specified
integrated mobile telephone (TDMA/
CDMA or GSM) and the telephone is
inserted in the cradle, the telephone
functions can be used as follows: 
at the COMAND

at the multifunction steering wheel

with the Voice control system*
This instruction manual describes the
operation at the COMAND. Unless
otherwise indicated, the descriptions
and illustrations refer to the COMAND.
Operation at the mobile phone and
operation with the Voice control
system* are described in separate
operating guides. Refer to the vehicle
Operator’s Manual for operation of the
telephone using the multifunction
steering wheel.
Which soft key functions are available
depends on the mobile phone variant.
iThe COMAND can display phone
number and name of the other party
(e.g. if the COMAND detects an
incoming call, but also in other menus).
For the number to be displayed, the
number information must be
transmitted with the incoming call. The
same goes for the name display which
additionally requires that the caller’s
number and name are saved in the
phone book.
iNo ring or DTMF tones will be heard
when a phone set to silent mode is in-
serted into the cradle.
For ringtone settings, refer to the sepa-
rate operating instructions for the
mobile phone.

94 Telephone*Telephone operationInitiating an emergency call
Telephone is locked
Press the
911
soft key.
The system opens an inquiry menu
prompting if you want to dial a “911”
call.
The selection marker in the inquiry
menu should be on
Yes
.

If necessary, press H to select Yes
.

Press E to confirm
Yes
if you want to
place the “911” emergency call.
The emergency call will be placed.

Wait until the emergency rescue
station answers and describe the
emergency.
If you do not want to place the emergency
call:

Press h to select
No
when the
inquiry menu appears.

Press E to confirm
No
.
Telephone is ready for operation

Press a repeatedly until the
telephone menu is displayed.

Press 9, 1 and 1 one after the
other.

Press E or press the
Send
soft key.
The emergency call will be placed.

Wait until the emergency rescue
station answers and describe the
emergency.iEnding the emergency call:
Depending on the cellular network, it
may be necessary to press the K
button on the mobile phone.

95 Telephone*
Telephone operation
Entering the unlock code
Use the number keys 1 through 0
to enter the four-digit unlock code.
Asterisks instead of digits will appear in
the input line.

Press the
OK
soft key.
If entered code is correct and the mobi-
le phone is registered in a network, the
mobile phone is ready for use.GSM mobile phone
Entering the PIN code

Enter the PIN code for the mobile pho-
ne. Refer to the mobile phone opera-
tor’s manual on how to do this.
If no SIM card is in the mobile phone,
the message
Check
SIM
Card
ap-
pears.

Insert a SIM card. Refer to the mo-
bile phone operator’s manual.
Entry incorrect:
You will hear a warning sound.

You need to re-enter your PIN code.
Entering codes
iYour unlock code prevents unauthori-
zed persons from using your mobile
phone. Be sure to memorize this code, a
four digit number, carefully.
If you enter an incorrect code, the sys-
tem returns to the menu for entering the
unlock code.iYou must always enter the unlock code
when you switch on the telephone the
first time (if mobile phone is in locked
mode). Warning
G
When in the enter unlock code screen, the
emergency number 911 (default input) will
be dialed if you press “1” longer than 2 se-
conds. The 911 emergency call system is a
public service. Using it without due cause is
a criminal offense.
!If the PIN is entered incorrectly three
times in a row, the SIM card will be
blocked. The message
SIM Card
Blocked
is displayed briefly. After that
the message
PIN Blocked
Please
Enter PUK on Cell Phone is
displayed.

99 Telephone*
Telephone operation

Use the number keys 1 - 0 to enter
the telephone number.
Deleting the last or several digits:
Press the
Delete
soft key once or
several times.
Deleting all digits:

Press K.
or

Press and hold
Delete
soft key for
more than 2 seconds.
Begin dialing

When you have entered the telephone
number, press k to confirm your
input.
or

In the Telephone menu, press the
Send

soft key.
or

Press E.Dialing will begin. If a name is associa-
ted with the phone number saved in the
phone book, the name appears on the
screen. In the status bar, the off-hook
symbol will appear.
COMAND will mute an active audio
source. If the person called answers
the call, the call is active. You talk over
the hands-free set.
Ending a call

Press K.
or

Press the
End
soft key.Subsequent dialing
Transmitting other dial tones:

During a call you can press the number
keys 1 through 0, # and *.
Redial

In the Telephone menu, press k or
E twice.
The telephone dials the number that
was dialed last.iIf the system is downloading the phone
book at that time (e.g. after inserting
the mobile phone) these tones may be
transmitted with delay.iIf you press k or E just once, the
dialed numbers list is displayed
(page 100).

100 Telephone*Telephone operationSelecting an entry from the dialed
numbers list
The COMAND automatically generates a
list of the last 10 numbers dialed. The list
is sorted chronologically with the most
recently dialed number at the top of the
list.
Displaying the list
In the Telephone menu (
page 96),
press the
Redial
soft key.
or

In the Telephone menu (
page 96),
press the
Calls
soft key.

Press H to display the dialed num-
bers list.
The most recently dialed number is
highlighted.The status bar shows:

the caller’s name if her or his name and
number are stored in the phone book

the message
Unknown
Name
if no entry
is available
You can select the following functions:

Changing the list display

Selecting an entry and begin dialing

Ending a call (
page 99)Changing the list display

Press the
123
soft key.
The display changes to names.
or

Press the
ABC
soft key.
The display changes to numbers.
Selecting an entry and begin dialing

Use g or G to select the desired
entry.

Press k.
or

Press E.
The telephone dials the number.
iDuplicate entries will be shown only
once. This means the list may contain
less than 10 entries.

101 Telephone*
Telephone operation
Selecting an entry from the received
calls list
The COMAND automatically generates a
list of the last 10 calls received. The list is
sorted chronologically with the most
recently received call at the top of the list.
Displaying the list
In the Telephone menu (
page 96),
press the
Calls
soft key.
The list is displayed and the most
recently received number is
highlighted. The status bar shows:

the caller’s name if her or his name and
number are stored in the phone book

the message
Unknown
Name
if no entry
is available

the telephone numberYou can select the following functions:

Changing list display (
page 100)

Selecting an entry and begin dialing
(page 100)

Ending a call (
page 99)
Missed calls
If there are one or more missed calls avai-
lable on the mobile phone, a correspon-
ding message will appear.

Press the
Back
soft key to return to the
Telephone menu.
or

Press a.
or

Press E.
iDuplicate entries will be shown only
once. This means the list may contain
less than 10 entries.

102 Telephone*Telephone operationSpeed-dialing
For all memory locations
At the mobile phone you can save
telephone numbers in the speed-dialing
memory and use them. Refer to the mobile
phone operator’s manual.
You can also use speed-dialing at the
COMAND (only mobile phone memory
locations 1-999).
You can enter up to 3 digits.
Open the Telephone menu
(page 96).
Memory locations with up to two digits:

Use the number keys 1 to 9 to
enter the memory location number.
Memory locations with three digits:

Use the number keys 1 to 9 to
enter the memory location number
followed by the # key.

Press k.
or

Press E.
The telephone dials the saved number.
Ending a call (
page 99)
Quick-dialing
Quick-dialing can be used on memory loca-
tions 1-9.

Open the Telephone menu
(page 96).

Press one of the number keys 1 - 9
longer than 2 seconds.
The telephone dials the saved number.
Ending a call (
page 99)If the person called or you answer a call,
the call is active. The call indication is
displayed.
Call menuYou talk over the hands-free set. You can
setting the volume for the hands-free
operation (
page 97).
The status bar indicates the call time.
Active call

103 Telephone*
Telephone operation
The following functions can be used during
a call:
Ending an active call

Switch on/off hands-free microphone

Change sound settings (Bal/Fad only),
(page 98)

Transmitting other dial tones
(page 99)Ending an active call

Press K.
The Telephone menu will appear.
Switching hands-free microphone on/
off (available if microphone is switched
on)
The microphone status is indicated by the
status of the
Mic Off
soft key.

Press the
Mic Off
soft key.
The microphone is switched on or off.
The soft key status changes
accordingly.
When the microphone is off, the other
party cannot hear you. You can still
hear your partner.
iYou can use three-way calling if this
feature is offered by your mobile phone
service provider.
Refer to the mobile phone operator’s
manual or contact your mobile phone
service provider for feature availability
and operating instructions.
Microphone
status
SymbolMic Off
On
white
Off
black