2005 MAZDA MODEL MX-5 window

Black plate (132,1)
Mode selector dial
Turn the mode selector dial to select
airflow mode (page 6-4).
A/C switchí
Push the switch to turn the air conditioner
on. The indicator light on the switch will
illuminate when the fan control dial is set
at position 1, 2, 3, or 4.
Push the switch once again to turn the air
conditioner off.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector
This lever controls the source of air
entering the vehicle.
It is recommended that under normal
conditions the lever be kept in the outside
air position.
Outside air position (
)
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
Recirculated air position (
)
Outside air is shut off. Air within the
vehicle is recirculated.
This position can be used when driving on
a dusty road or in similar conditions. It
also helps to provide quicker cooling of
the interior.
WARNING
The Recirculated Air Position:
Using the
position in cold or
rainy weather will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident. Do not use the
position in cold or rainy weather.
6-6
Interior Comfort
íSome models.
Climate Control System
MX-5 Miata_8T72-EA-04G_Edition1 Page132
Wednesday, June 9 2004 3:5 PM
Form No.8T72-EA-04G

Black plate (133,1)
Rear window defroster switch
When using the rear window defroster
switch, refer to Rear Window Defroster
(page 5-33).
qHeating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidified heating is desired, turn
on the air conditioner.
NOTE
lIf the windshield fogs up easily, set
the mode selector dial to the
position.
lIf cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qCooling (With Air Conditioner)í
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner.
5. Adjust the fan control dial and
temperature control dial to maintain
maximum comfort.
CAUTION
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-20).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner off.
NOTE
lWhen maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the
position,
then set the fan control dial to
position 4.
lIf warmer air is desired at floor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Interior Comfort
Climate Control System
6-7íSome models. MX-5 Miata_8T72-EA-04G_Edition1 Page133
Wednesday, June 9 2004 3:5 PM
Form No.8T72-EA-04G

Black plate (134,1)
qVentilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
qWindshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
WARNING
Foggy Windshield:
Using the
position with the
temperature control set to the cold
position will cause the outside of the
windshield to fog up. Your vision will
be hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the
position.
NOTE
lFor maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
lIf warm air is desired at the floor, set
the mode selector dial to the
position.
qDehumidifying (With Air
Conditioner)í
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
5. Turn on the air conditioner.
6-8
Interior Comfort
íSome models.
Climate Control System
MX-5 Miata_8T72-EA-04G_Edition1 Page134
Wednesday, June 9 2004 3:5 PM
Form No.8T72-EA-04G

Black plate (242,1)
2. Unfasten the clamps.
3. Lift off the air filter cover and remove
the filter.
Air filter cover
Air filter
4. Wipe inside the air cleaner housing
with a damp cloth.
5. Clean or replace the filter.
6. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3).
Wiper Blades
CAUTION
lHot waxes applied by automatic car
washers have been known to affect
the wiper's ability to clean windows.
lTo prevent damage to the wiper
blades, don't use gasoline, kerosene,
paint thinner, or other solvents on or
near them.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
qReplacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, don't move the
wipers by hand.
8-26
Maintenance and Care
Owner Maintenance
MX-5 Miata_8T72-EA-04G_Edition1 Page242
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (256,1)
Fuse panel (Driver's side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1AD
FA N
*120AAdd fan motor, Magnet
clutch
2
HEAD.LH15A Headlights (LH)
3
HEAD.RH15A Headlights (RH)
4―― ―
5 ST.SIG 7.5AInstrument cluster, Cruise
control
í
6FAN*230ACooling fan, Additional fan
(air conditioner)
7 CIGAR 20A Cigar lighter
8 RADIO 10A Audio
í
9 F.FOG 15A Fog lightsí
10 TAIL 15ATaillights, Front parking
lights, Side-marker lights
11 ENGINE 15A Engine control system
12 METER 15A Instrument cluster
13 TURN 7.5A Turn signal lights
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
14 A/B 10ASupplemental restraint
system, Antilock brake
system
í
15 WIPER 20AWindshield wipers and
washer
16 P.WIND 30A Power windows
17 A/C 7.5A Air conditioner
í
18HAZARD10A Turn signal lights
19 D.LOCK 10A Power door lockí
20 AUDIO 20A Audio ampí
21 DEFOG 15A Rear defroster
22 ROOM 10AInterior light, Auto
antenna, Warning buzzers
*1 MX-5/Miata
*2 MAZDASPEED MX-5
8-40
Maintenance and Care
íSome models.
Owner Maintenance
MX-5 Miata_8T72-EA-04G_Edition1 Page256
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (262,1)
qConvertible Top Maintenance
The convertible top is made of a special
high-grade material, but if it's not taken
good care of, hardening, staining, and loss
of luster will result. Maintain it under
these guidelines.
Washing
Don't wait until the top gets really dirty
before cleaning it. Dirt that's there too
long will cause deterioration.
1. Before washing, remove dust and
coarse particulate with a soft brush.
2. Gently clean the top with a synthetic
neutral detergent, lots of water, and a
soft brush.
3. Rinse it thoroughly with clean water to
remove all the soap.
4. Wipe it as dry as you can before the
water dries on it.
5. Then allow it to dry completely before
lowering it.
CAUTION
lAutomatic and high-pressure car
washes are harmful to a convertible
top. Avoid them.
lDon't spray water directly on the
area where the window glass and the
top meet. This would probably cause
water to enter the cabin.
Appearance(Polyvinyl only)
Dress the top once a month after washing
and drying it well. For best results, use a
water-based leather treatment or vinyl top
dressing. This will help maintain good
appearance and material condition of the
top.
CAUTION
lSome leather treatment products can
ruin the top's gloss. Be careful of the
one you choose.
lTest on an inconspicuous, small
corner of the top if you are not sure.
lDon't get any car wax on the top.
If you do, remove it with a good
leather cleaner.
lToo much treatment on the top can
be as damaging as too little. Follow
the manufacturer's directions.
Don't overdo it!
lLet the top dry completely before
lowering after applying treatment or
dressing.
qDetachable Hardtop
Maintenanceí
Washing
To help protect the hardtop's finish, use a
soft cloth or sponge to wash it.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if they are not removed
immediately. When prompt washing with
plain water is ineffective use a mild soap
made for use on vehicles.
8-46
Maintenance and Care
íSome models.
Appearance Care
MX-5 Miata_8T72-EA-04G_Edition1 Page262
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (264,1)
Fabric
Remove dust and loose dirt from fabric
with a whisk broom or vacuum cleaner.
Clean it with a mild soap solution good
for upholstery and carpets. Remove fresh
spots immediately with a fabric spot
cleaner.
To keep the fabric looking clean and
fresh, take care of it. Otherwise its color
will be affected, it can be stained easily,
and its fire-resistance may be reduced.
CAUTION
Use only recommended cleaners and
procedures. Others may affect
appearance and fire-resistance.
qCleaning the Lap/Shoulder Belt
Webbing
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don't bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.
WARNING
Damaged Seat Belt:
Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have an Authorized Mazda
Dealer replace damaged belts
immediately.
qCleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them
with glass cleaner. Follow the directions
on the container.
CAUTION
Don't scrape or scratch the inside of the
rear window. You may damage the rear
window defroster grid.
8-48
Maintenance and Care
Appearance Care
MX-5 Miata_8T72-EA-04G_Edition1 Page264
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (292,1)
A
Add-On Non-Genuine Parts and
Accessories ....................................... 9-12
Air Bag Systems ............................... 2-20
Air Conditioning System
Gas specifications ...................... 10-5
Air Filter ............................................ 8-25
Antenna ............................................... 6-9
Anti-Lock Brake System (ABS) ......... 5-7
Warning light ............................... 5-7
Appearance Care ............................... 8-41
Ashtray .............................................. 6-68
Audio System ..................................... 6-9
Audio set (Type A) ..................... 6-19
Audio set (Type B) ..................... 6-43
Operating tips for audio system .... 6-9
Safety certification ..................... 6-66
Automatic Transmission
Driving tips ................................ 5-13
Fluid ........................................... 8-22
Overdrive ................................... 5-12
Shift-lock override ..................... 5-12
Shift-lock system ........................ 5-11
Transmission ranges ................... 5-10
B
Battery
Emergency starting .................... 7-13
Maintenance ............................... 8-28
Specifications ............................. 10-4
Beep Sounds
Ignition key reminder ................. 5-28
Lights-on reminder ..................... 5-28
Seat belt warning beep ............... 5-28
Before Starting the Engine .................. 4-7
After getting in ............................. 4-7
Before getting in .......................... 4-7
Body Lubrication .............................. 8-25
B
Brake
Fluid ........................................... 8-19
Brakes
Anti-lock brake system (ABS) ..... 5-7
Foot brake .................................... 5-4
Pad wear indicator ........................ 5-8
Parking brake ............................... 5-5
Warning light ............................... 5-6
Break-In Period ................................... 4-8
Bulb Replacement ............................. 8-33
C
Capacities .......................................... 10-5
Carbon Monoxide ............................... 4-6
Catalytic Converter ............................. 4-4
Cell Phones ....................................... 9-13
Center Console .................................. 6-70
Child Restraint
Child restraint precautions ......... 2-13
LATCH child-restraint
systems ....................................... 2-18
Cigarette Lighter ............................... 6-68
Climate Control System ...................... 6-2
Clutch
Fluid ........................................... 8-20
Convertible Top ................................ 3-20
Cruise Control ................................... 5-14
Cup Holder ........................................ 6-69
Customer Assistance ........................... 9-2
D
Dashboard Illumination .................... 5-21
Daytime Running Lights ................... 5-31
Defroster
Rear window .............................. 5-33
Detachable Hardtop .......................... 3-25
11-2
Index
MX-5 Miata_8T72-EA-04G_Edition1 Page292
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G