Page 440 of 539

IN CASE OF AN EMERGENCY
421
Emergency towing eyelet precautions:
Before emergency towing, check that the eyelet is not
broken or damaged and that the installation bolts are not
loose.
Fasten the towing cable or chain securely to the eyelet.
Do not jerk the eyelet. Apply steady and even force.
To avoid damaging the eyelet, do not pull from the side or
at a vertical angle. Always pull straight ahead.
CAUTION
If the emergency towing eyelet is used to get out when
your vehicle becomes stuck in the mud, sand or other
condition from which the vehicle cannot be driven out
under its own power, make sure to observe the
precautions mentioned below. Otherwise, excessive
stress will be put on the eyelet and the towing cable or
chain may break, causing serious injury or damage.
If the towing vehicle can hardly move, do not forcibly
continue the towing. Contact your Lexus dealer or a
commercial tow truck service for assistance.
Tow the vehicle as straight ahead as possible.
Keep away from the vehicle during towing.
Tips for towing a stuck vehicle:
The following methods are effective to use when your
vehicle is stuck in the mud, sand or other condition from
which the vehicle cannot be driven out under its own
power. Use extreme caution when towing the vehicle. In
addition, keep a way from the vehicles and towing cable or
chain when towing.
Remove the sand and soil in the front and the back of the
tires.
Place stones or wood under the tires.
Page 441 of 539
IN CASE OF AN EMERGENCY
422
(e) Installing towing eyelet
40L178a
1. Remove the towing eyelet cover on the front bumper by
pushing the right side of the cover.
40L179
2. Use the towing eyelet in the trunk. Secure it to the hole on
the bumper by turning clockwise. (For the eyelet location, see
page 408.)
40L180
3. Tighten the towing eyelet securely by a wheel nut wrench.
CAUTION
When installing the eyelet on the vehicle, be sure to
tighten the eyelet securely. If the eyelet is loose, it may
come off when being towed and result in death or
serious injury.
Page 458 of 539

INTRODUCTION
439
PARTS AND TOOLS
Here is a list of parts and tools you will need to perform
do−it−yourself maintenance. Remember all Lexus parts are
designed in metric sizes, so your tools must be metric.
Checking the engine oil level
Parts (if level is low):
“Toyota Genuine Motor Oil” or equivalent
Oil grade: API grade SL “Energy −Conserving” or ILSAC
multigrade engine oil. For recommended oil viscosity, see
page 454.
Tools:
Rag or paper towel
Funnel (only for adding oil)
Checking the engine coolant level
Parts (if level is low):
“Toyota Super Long Life Coolant” or similar high quality
ethylene glycol based non −silicate, non −amine, non −nitrite,
and non −borate coolant with long −life hybrid organic acid
technology. (Coolant with long −life hybrid organic acid
technology is a combination of low phosphates and organic
acids.)
“Toyota Super Long Life Coolant” is a mixture of 50%
coolant and 50% deionized water (for the U.S.A.) or 55%
coolant and 45% deionized water (for Canada).
Distilled water
Tools:
Funnel (only for adding coolant)
Checking brake fluid
Parts (if level is low):
FMVSS No. 116 DOT 3 or SAE J1703 brake fluid
Tools:
Funnel (only for adding fluid)
Page 459 of 539
INTRODUCTION
440
Checking power steering fluid
Parts (if level is low):
Automatic transmission fluid DEXRON
\bII or III
Tools:
Rag or paper towel
Funnel (only for adding fluid)
Checking battery condition
Tools:
Warm water
Baking soda
Grease
Conventional wrench (for terminal clamp bolts)
Checking and replacing the blade type fuses
Parts (if replacement is necessary):
Fuse with same amperage rating as original
Checking the cartridge type fuses
Parts (if replacement is necessary):
Genuine Lexus fuse or equivalent with same amperage
rating as original
Adding washer fluid
Parts:
Water
Washer fluid containing antifreeze (for winter use)
Tools:
Funnel
Page 530 of 539
BODY
511
370.SPECIFICATIONS
– DIMENSIONS AND WEIGHTSOverall length
5015 mm (197.4 in.)
Overall width1830 mm (72.0 in.)
Overall height– with electronically modulated air suspension
– without electronically modulated air suspension
1470 mm (57.9 in.)*
1490 mm (58.7 in.)*
Wheelbase2925 mm (115.2 in.)
Tread
– Frontwith electronically modulated air suspension
without electronically modulated air suspension
– Rear with electronically modulated air suspension
without electronically modulated air suspension
1575 mm (62.0 in.)
1570 mm (61.8 in.)
1575 mm (62.0 in.)
1570 mm (61.8 in.)
Vehicle capacity weight (occupants + cargo)410 kg (900 lb.)
Towing capacity (trailer weight + cargo weight)907 kg (2000 lb.)
*Unladen vehicle
– FUEL TANK
Capacity
84 L (22.2 gal., 18.5 lmp.gal.)
Page 533 of 539

BODY
514Plastic wheel
ornaments: The plastic wheel ornaments are
damaged easily by organic substances. If any organic
substance splashes an ornament, be sure to wash it off with
water and check if the ornament is damaged.
CAUTION
Do not attach the heavily damaged plastic wheel
ornament. It may fly off the wheel and cause accidents
while the vehicle is moving.
Aluminum wheels: Use only a mild soap or neutral detergent.
Urethane bumpers and side moldings: Wash carefully. Do
not scrub with abrasive cleaners. The bumper and side
molding faces are soft.
Road tar: Remove with turpentine or cleaners that are marked
safe for painted surfaces.
NOTICE
Do not use organic substances (gasoline, kerosene,
benzine or strong solvents), which may be toxic or
cause damage.
3. Rinse thoroughly − dried soap can cause streaking. In hot
weather you may need to rinse each section right after you
wash it.
4. To prevent water spots, dry the vehicle using a clean soft
cotton towel. Do not rub or press hard − you might scratch the
paint.
Automatic car wash
NOTICE
To prevent damage to the antenna, make sure to remove
it before driving your Lexus through an automatic car
wash.
Your vehicle may be washed in an automatic car wash, but
remember that the paint can be scratched by some types of
brushes, unfiltered washing water, or the washing process
itself. Scratching reduces paint durability and gloss, especially
on darker colors. The manager of the car wash should be able
to advise you whether the process is safe for the paint on your
vehicle.
Waxing your Lexus
Polishing and waxing is recommended to maintain the
original beauty of your Lexus’ finish.
Apply wax once a month or if the vehicle surface does not repel
water well.
1. Always wash and dry the vehicle before you begin waxing,
even if you are using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become
extremely weathered, use a car −cleaning polish, followed by
a separate wax. Carefully follow the manufacturer’s
instructions and precautions. Be sure to polish and wax the
chrome trim as well as the paint.