Page 430 of 539
IN CASE OF AN EMERGENCY
411
40L170
4. Position the jack at the jack points as shown.
Make sure the jack is positioned on a level and solid
surface.
40L162
5. After making sure no one is in the vehicle, raise it
high enough so that the spare tire can be installed.
Allow for the fact that you need more ground clearance
when putting on the spare tire than when removing the
flat tire.
To raise the vehicle, insert the jack handle into the jack
(it is a loose fit) and turn it clockwise. As the jack touches
the vehicle and begins to lift, double −check that it is
properly positioned.
CAUTION
Never get under the vehicle when the vehicle is
supported by the jack alone.
Page 433 of 539

IN CASE OF AN EMERGENCY
414
40L167
9. Lower the vehicle completely and tighten the
wheel nuts.
Turn the jack handle counterclockwise to lower the
vehicle.
Use only the wheel nut wrench to tighten the nuts. Do
not use other tools or any additional leverage other than
your hands, such as a hammer, pipe or your foot. Make
sure the wrench is securely engaged over the nut.
Tighten each nut a little at a time in the order shown.
Repeat the process until all the nuts are tight.
CAUTION
When lowering the vehicle, make sure all
portions of your body and all other persons
around will not be injured as the vehicle is
lowered to the ground.
Have the wheel nuts tightened with torque
wrench to 103 N·m (10.5 kgf·m, 76 ft·lbf.), as
soon as possible after changing wheels.
Otherwise, the nuts may loosen and the wheels
may fall off, which could cause a serious
accident.
10. After changing the wheel, check the air pressure
of the replaced tire. Stow all the tools, jack and flat
tire securely.
If the pressure of the replaced tire is low, drive slowly to
the nearest service station and fill to the correct
pressure.
Do not forget to reinstall the tire valve cap as dirt and
moisture could get into the valve core and possibly
cause air leakage. If the cap is missing, put a new one
on as soon as possible.
This is the same procedure for changing or rotating your
tires.
Page 441 of 539
IN CASE OF AN EMERGENCY
422
(e) Installing towing eyelet
40L178a
1. Remove the towing eyelet cover on the front bumper by
pushing the right side of the cover.
40L179
2. Use the towing eyelet in the trunk. Secure it to the hole on
the bumper by turning clockwise. (For the eyelet location, see
page 408.)
40L180
3. Tighten the towing eyelet securely by a wheel nut wrench.
CAUTION
When installing the eyelet on the vehicle, be sure to
tighten the eyelet securely. If the eyelet is loose, it may
come off when being towed and result in death or
serious injury.
Page 472 of 539
ENGINE
453
62L019c
If the oil level is below or only slightly above the low mark,
add engine oil of the same type as already in the engine.
Remove the oil filler cap and add engine oil a little at a time,
checking the dipstick. We recommend that you use a funnel
when adding oil. The approximate quantity of oil needed to fill
between the low level mark and the full level mark on the
dipstick is indicated below for reference.
When the level reaches within the correct range, return the
filler cap and turn the cap clockwise until you hear a click.
Oil quantity. L (qt., lmp. qt.) 1.5 (1.6, 1.3)
NOTICE
Be careful not to spill engine oil on the vehicle
components.
Avoid overfilling, or the engine could be damaged.
Check the oil level on the dipstick once again after
adding the oil.
Page 486 of 539

CHASSIS
467
CHECKING POWER STEERINGFLUID
63L011a
Check the fluid level on the through the reservoir. If
necessary, add automatic transmission fluid DEXRON\bII
or III.
If the vehicle has been driven around 80 km/h (50 mph) for 20
minutes (a little more in frigid temperatures), the fluid is hot
(60 C − 80C or 140F − 175F). You may also check the level
when the fluid is cold (about room temperature, 10 C − 30C
or 50F − 85F) if the engine has not been run for about five
hours.
63L012a
1 If cold O.K. 2If hot O.K. 3If cold add
4If hot add
Clean all dirt off the reservoir and look at the fluid level. If the
fluid is cold, the level should be in the “COLD” range. Similarly,
if it is hot, the fluid level should be in the “HOT” range. If th\
e
level is at the low side of the appropriate range, add automatic
transmission fluid DEXRON
\bII or III to bring the level within
the range.
To remove the reservoir cap, turn it counterclockwise and lift
up. To reinstall it, turn it clockwise. After replacing the reservoir
cap, visually check the steering box case, vane pump and hose
connections for leaks or damage.
Page 511 of 539
ELECTRICAL COMPONENTS
492
64L206
Engine compartment
No.FUSEAMPERECIRCUIT
1 TI & TE20Tilt and telescopic steering
2 PANEL7.5
Lexus park assist system, Rear
seat heater, Rear climate
control seat, Multi− information
display, Audio system,
Cigarette lighter, Instrument
panel light, Coin box light, Rear
mirror light, Glove box light,
Power rear seat, Electronically
modulated air suspension
system, Turn signal lights,
Clock, Shift lock system,
Vehicle stability control system,
Sunshade, Power rear view
mirror control system, Console
box light, Fuel opener system,
Adaptive Front Lighting System
(AFS)
3 D P/SEAT30Power seat system
4 GAUGE7.5Gauges and meters, Lexus
park assist system, Shift lock
system
5 MPX IG7.5
Tilt and telescopic steering,
Power door lock system, Power
seat system, Engine
immobilizer system
6 D S/HTR15Seat heater, Climate control
seat system
7 AIR SUS20Electronically modulated air
suspension system
8 D ACC7.5Shift lock system, Theft
deterrent system
Page 512 of 539