2005 LEXUS LS430 cruise control

GAUGES, METERS AND SERVICE REMINDER INDICATORS
103
w280
If the system cannot easily measure the
vehicletovehicle distance because of the following
conditions while the dynamic radar/laser cruise control is
on, the master warning light comes on, the “CRUISE”
indicator light flashes, and a warning tone sounds. At this
time the above message appears.
Dynamic radar cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as extremely hot weather)
 The wipers are operated at high speed with the wiper lever
in the “AUTO” position
Dynamic laser cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as rainy, foggy, or snowy
weather)
 The wipers are operated at high or low speeds with the
wiper lever in the “AUTO” position.
 Direct sunlight from the front In the following
cases, the dynamic radar/laser cruise
control switches to the “RADAR READY” mode:
Dynamic radar cruise control—
 The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to low speed or
intermittent operation. (Including intermittent and stopped
wipers in the “AUTO” position)
In the above conditions, press the control lever upward in the
“RES/ACC” direction and release it. The dynamic radar cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
104Dynamic laser cruise control—

The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to intermittent
operation. (Including intermittent and stopped wipers in the
“AUTO” position)
 No direct sunlight from the front
In the above conditions, press the control lever upward in the
“RES/ACC” direction and release it. The dynamic laser cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.
w281
If a system malfunction is detected when dynamic
radar/laser cruise control is in the “RADAR READY” mode
or operating, the master warning light comes on, the
“CRUISE” indicator light flashes and a warning tone
sounds. At this time the above message appears.
If this message appears, stop your vehicle in a safe place, turn
the ignition off, and then restart it to reset the system. If the
setting still cannot be made or the same message appears
again, the system might have malfunctioned. Although it is no
problem to continue driving, contact your Lexus dealer.
NOTICE
While you are cruising with the dynamic radar/laser
cruise control on, if the master warning light comes on,
the cruise indicator light flashes, “Check Cruise
System” appears on the multiinformation display and
the warning tone sounds, turn the ignition switch off
and then on again. If the function is cancelled again
after setting or if settings cannot be made, the dynamic
radar/laser cruise control system may be
malfunctioning. Although it is no problem to continue
driving, have your vehicle checked by your Lexus
dealer.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
105
w278
The master warning light comes on, a warning tone
sounds and the above message appears in the following
conditions:
The millimeter wave radar sensor or the grille cover is
dirty.
Clean the grille or sensor with a soft cloth to remove the dirt.
 The precollision seat belts are activated repeatedly for
a short time.
The system turns of f temporarily for overheating protection,
but turns back on after a while.
w277
If there is a problem somewhere in the precollision safety
system, the master warning light comes on, a warning
tone sounds, and the above message appears.
If the above message appears, the pre −collision safety system
may not operate. Contact your Lexus dealer as soon as
possible to service the vehicle.
COMPASS
(Vehicles without Navigation System)
13L149
When the ignition is turned on, the previously selected display
appears. If the compass is not displayed, push the “DISP2”
button several times for 1 to 2 seconds to display the compass.
However if you push the main switch of dynamic radar/laser
cruise control to use dynamic radar/laser cruise control, the
dynamic radar/laser cruise control display appears. To change
to the compass display, push the “DISP2” button for longer
than about 1 second.
The compass indicates the direction in which the vehicle
is heading. The illustration shown above indicates that the
vehicle is heading north.

SECTION 3 – 1
295
STARTING AND DRIVING
Starting and driving
Three−way catalytic converters296
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution 297
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine 298
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart ignition system with steering lock 298
. . . . . . . . . . . . . . . . . . . . .
Ignition switch with steering lock 301
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
How to start the engine 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 305
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic throttle control system 315
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lexus park assist system 316
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view monitor system 323
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control 326
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Dynamic radar/laser cruise control 329
. . . . . . . . . . . . . . . . . . . . . . . . .
Electronically modulated air suspension 360
. . . . . . . . . . . . . . . . . . . . .
Traction control system 362
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle stability control system 364
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system 366
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Tire pressure warning system 370
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake pad wear limit indicators 373
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre−collision safety system 374
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING AND DRIVING
311
(c) Using engine braking
31L327
“S” mode position
To use the braking power of the engine, downshift the range in
the “S” mode position as follows:
 Shift into the “5” (fifth range) position. The transmission will
downshift to fifth gear and engine braking will be enabled.
If you drive in the “D” position: Shift the selector lever to
the “S” position and “5” (fifth range) will automatically \
be
selected.
If you drive in the “S” position: Shift the selector lever
down to the “–” position by selecting the “5” (fifth ran\
ge). Vehicles with the cruise control —
When
the cruise control is being used, even if you downshift
from “D” or “6” (sixth range) to “5” (fifth range)\
, engine
braking will not be enabled because the cruise control is not
cancelled. For vehicle speed reduction, see page 328.
Vehicles with the dynamic radar/laser cruise control —
When the cruise control is being used in the conventional
(fixed speed) cruise control mode or in the
vehicle −to−vehicle distance control mode, even if you
downshift from “D” or “6” (sixth range) to “5” (fif\
th range),
engine braking will not be enabled because the cruise
control is not cancelled. For vehicle speed reduction, see
pages 359 and 344.
 Shift into the “4” (fourth range) position. The transmission
will downshift to fourth gear when the vehicle speed is or
becomes lower than 197 km/h (122 mph) and more
powerful engine braking will be enabled.
If you drive in the “D” position: Shift the selector lever to
the “S” position and shift the lever down to the “–” posi\
tion
once to select “4” (fourth range). However, when you move
the lever to the “S” position while the AI shifting control is
operating, the first shift range will be “5” (fifth range), “4”
(fourth r ange) or “3” (third range) because the suitable shift
range is selected depending on the driving condition.
If you drive in the “S” position: Shift the selector lever
down to the “–” position to select the “4” (fourth range\
).

STARTING AND DRIVING
312Vehicles with the cruise control —
When
the cruise control is being used, even if you downshift
from “D” or “5” (fifth range) to “4” (fourth range)\
, engine
braking will not be enabled because the cruise control is not
cancelled. For vehicle speed reduction, see page 328.
Vehicles with the dynamic radar/laser cruise control —
When the cruise control is being used in the conventional
(fixed speed) cruise control mode or in the
vehicle −to−vehicle distance control mode, even if you
downshift from “D” or “5” (fifth range) to “4” (fourth range),
engine braking will not be enabled because the cruise
control is not cancelled. For vehicle speed reduction, see
pages 359 and 344.
 Shift into the “3” (third range) position. The transmission will
downshift to third gear when the vehicle speed is or
becomes lower than 146 km/h (91 mph) and more powerful
engine braking will be enabled.
If you drive in the “D” position: Shift the selector lever to
the “S” position and shift the lever down to the “–” posi\
tion
twice to select the “3” (third range). However, when you
move the lever to the “S” position while the AI shifting control
is operating, the first shift range will be “5” (fifth range), “\
4”
(fourth range) or “3” (third range) because the suitable shift
range is selected depending on the driving condition.
If you drive in the “S” position: Shift the selector lever
down to the “–” position to select “3” (third range). 
Shift into the “2” (second range) position. The transmission
will downshift to second gear when the vehicle speed is or
becomes lower than 98 km/h (61 mph) and more powerful
engine braking than that of the “3” (third range) position will
be enabled.
If you drive in the “D” position: Shift the selector lever to
the “S” position and shift the lever down to the “–” posi\
tion
three times to select “2” (second range).
If you drive in the “S” position: Shift the selector lever
down to the “–” position to select “2” (second range).
 Shift into the “1” (first range) position. The transmission will
downshift to first gear when the vehicle speed is or becomes
lower than 35 km/h (22 mph) and maximum engine braking
will be enabled.
If you drive in the “D” position: Shift the selector lever to
the “S” position and shift the lever down to the “–” posi\
tion
four times to select “1” (first range).
If you drive in the “S” position: Shift the selector lever
down to the “–” position to select “1” (first range).
CAUTION
Be careful when downshifting on a slippery surface.
The abrupt change in engine speed could cause the
vehicle to skid or spin.

STARTING AND DRIVING
326
31L357
Check surroundings for safety.
If a bright light (for example, sunlight reflected off the vehicle
body) is picked up by the camera, the smear effect* peculiar
to the camera may occur.
*: Smear effect — A phenomenon that occurs when a bright
light (for example, sunlight reflected off the vehicle body) is
picked up by the camera; when transmitted by the camera, the
light source appears to have a vertical streak above and below
it.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over about 40 km/h (25 mph) with your foot
off the accelerator pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, a great
speed change will occur so it is better to drive without the cruise
control.
When the cruise control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.
CAUTION
 To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snowcovered) or winding roads.
 Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation to
the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.

STARTING AND DRIVING
327
Turning the system on
31L629
To operate the cruise control, push the “ON−OFF” button. This
turns the system on. The indicator light in the instrument
cluster shows that you can now set your desired cruising
speed. Another push on the button will turn the system
completely off.
When the ignition switch is turned off, the “ON −OFF” button is
also automatically turned off. To use the cruise control again,
push the “ON −OFF” button again to turn it on.
CAUTION
To avoid accidental cruise control engagement, keep
the “ONOFF” button off when not using the cruise
control.
Setting operation
31L630
 Each function is described below.
1
Setting at a desired speed.
The transmission must be in the “D” position, or the shift range
position must be “4” (fourth range), “5” (fifth range) o\
r “6” (sixth
range) in the “S” mode before you set the cruise control speed.
Bring the vehicle to the desired speed, press the control lever
downward in the “– SET” direction and release it. This sets the
vehicle at that speed. Now you may take your foot off the
accelerator pedal. If you need acceleration − for example,
when passing − depress the accelerator pedal enough for the
vehicle to exceed the set speed. When you release the
accelerator pe dal, the vehicle will return to the speed set prior
to the acceleration.