2005 LEXUS LS430 light

AIR CONDITIONING
255
These
are the controls added to the front air conditioning when
your vehicle is equipped with a rear air conditioning. The
controls for the rear passengers and for the front passengers
both work the same, so operation can be made with the
controls on either panel.
(a) Controls and Functions
This rear air conditioning is equipped with dustproof and
deodorant filter with photocatalyst. When light in the
xenon tube (ultraviolet rays) hits the filter, odious
ingredients adsorbed in the filter are oxidized and
decomposed to deliver clean air in the interior.
REAR AIR CONDITIONING ONOFF
Push the “AUTO” button to turn the air conditioning on,
and push the “OFF” button to turn it off.
AIR FLOW CONTROL
The mode changes every time the “LO HI A/C” button is
pushed.
AUTO mode − Turns the fan operation to automatic.
LO speed mode − Turns the fan at low speed.
HI speed mode − Turns the fan at high speed.
(b) Rear Cooling
1. Turn the front air conditioning on. The rear cooler will not
turn on if the front air conditioning is off.
2. Turn the rear air conditioning on. The fan speed and rear
cooler are adjusted automatically.
3. Use either of the “LO HI A/C” buttons to adjust the desired
fan speed and the rear cooler. Each indicator light shows
which mode is now selected.
(c) Air Purifier
The air purifier operates whenever the rear air conditioning or
the rear fan operation is on, regardless of front air conditioning
activation.

AIR CONDITIONING
256
(d) Replacing the photocatalyst filter for therear seats
This rear air conditioning is equipped with dustproof and
deodorant filter with photocatalyst.
Replace the air filter when the use of rear air conditioning or air
purification function reduces air flow or deodorant
performance.
This filter is an interchangeable type. Do not clean the filter by
washing or air blowing. The use of filter after washing or
cleaning may cause a malfunction of the system. Be sure to
replace it with a new one.
The filter is located in the trunk.
Replace the filter using the following procedures.
1. Be sure to turn the ignition switch to “LOCK”.
21L210
 1 Air purifier 2Filter cover
2. Open the trunk and remove the filter cover in the trunk.
21L211
 1 Filter case 2Filter
3. Pull out the filter case toward you.
4. Replace the filter.
When you install the filter, face the filter surface (gray)
downward and fit the filter folds properly in the case as shown.
5. Install the filter in the reverse order of removal.
The gray surface in the filter may turn to yellow (yellow spots)
because of ultraviolet rays included in the light, however it is
no problem for use.

AIR CONDITIONING
257
When the ignition switch is turned on, the xenon tube comes
on even if the rear air conditioning or rear fan is not operating.
This
does not indicate a malfunction but is required for the long
use of the photocatalyst.
NOTICE
 Do not look into the xenon tube in the air purifier
through the filter slot and do not expose your skin
directly to the light in the xenon tube also. Although
the xenon tube scarcely issues less than 300nm
ultraviolet rays which are thought harmful for the
human body, some people may have symptoms such
as eye sore, vision trouble, skin inflammation, etc.
 Do not disassemble the air purifier , or it may cause a
malfunction. As some part in the purifier is under
high voltage, you may get an electric shock when you
touch it.
 The filters should be installed properly in position.
The use of rear air conditioning controls with the filter
removed may cause the malfunction of the rear air
conditioning controls.
 Turn on the air conditioning with a filter in position.
The activation without an filter may not only cause a
malfunction of the system but also dirty the interior
by spouting dust.

AUDIO
283
20L145b
Ejecting a single CD:
1. Push the button under the “
” or “” signal on the
display to display the CD number you want to eject.
2. Push the “
” (eject) button briefly.
At this time, the display shows “ EJECT” and the indicators at
both ends of the slot as well as the CD number light up.
 Ejecting all the CDs:
Push the “
” (eject) button until you hear a beep.
However, if you accidentally pushed the “
” (eject) button,
push the “DISC” or “LOAD” button to insert the CD again.
Do not push in the CD which is being ejected forcibly. (b) Playing a CD
20L366
Push the “DISC” button if the CDs are already loaded in
the player.
“CD” appears on the display.
The CDs set in the player are played continuously
, starting with
the last CD you inserted. The CD number of the CD currently
being played, the track number and the time from the
beginning of the program appear on the display.
When play of one CD ends, the first track of the following CD
starts. When play of the final CD ends, play of the first CD
starts again.
The player will skip any empty CD number.

AUDIO
290Radio reception
Usually, a problem with radio reception does not mean there
is a problem with your radio
− it is just the normal result of
conditions outside the vehicle.
For example, nearby buildings and terrain can interfere with
FM reception. Power lines or telephone wires can interfere
with AM signals. And of course, radio signals have a limited
range. The farther you are from a station, the weaker its signal
will be. In addition, reception conditions change constantly as
your vehicle moves.
Here are some common reception problems that probably do
not indicate a problem with your radio:
FM
Fading and drifting stations − Generally, the ef fective range
of FM is about 40 km (25 miles). Once outside this range, you
may notice fading and drifting, which increase with the
distance from the radio transmitter. They are often
accompanied by distortion.
Multipath − FM signals are reflective, making it possible for
two signals to reach your antenna at the same time. If this
happens, the signals will cancel each other out, causing a
momentary flutter or loss of reception.
Static and fluttering − These occur when signals are blocked
by buildings, trees, or other large objects. Increasing the bass
level may reduce static and fluttering. Station swapping −
If the FM signal you are listening to is
interrupted or weakened, and there is another strong station
nearby on the FM band, your radio may tune in the second
station until the original signal can be picked up again.
AM
Fading − AM broadcasts are reflected by the upper
atmosphere − especially at night. These reflected signals can
interfere with those received directly from the radio station,
causing the radio station to sound alternately strong and weak.
Station interference − When a reflected signal and a signal
received directly from a radio station are very ne arly the same
frequency, they can interfere with each other, making it dif ficult
to hear the broadcast.
Static − AM is easily affected by external sources of electrical
noise, such as high tension power lines, lightening, or electrical
motors. This results in static.
Caring for your cassette player and tapes
For the best performance for your cassette player and tapes:
Clean the tape head and other parts regularly.
 A dirty tape head or tape path can decrease sound quality
and tangle your cassette tapes. The easiest way to clean
them is by using a cleaning tape. (A wet type is
recommended.)

AUDIO
291
Use high−
quality cassettes:
 Low −quality cassette tapes can cause many problems,
including poor sound, inconsistent playing speed, and
constant auto− reversing. They can also get stuck or
tangled in the cassette player.
 Do not use a cassette if it has been damaged or tangled or
if its label is peeling off.
 Do not leave a cassette in the player if you are not listening
to it, especially if it is hot outside.
 Store cassettes in their cases and out of direct sunlight.
 Avoid using cassettes with a total playing time longer than
100 minutes (50 minutes per side). The tape used in these
cassettes is thin and could get stuck or tangled in the
cassette player. Caring for your CD player and CDs

Your CD player is intended for use with 12 cm (4.7 in.) CDs
only.
 Extremely high temperature can keep your CD player from
working. On hot days, use air conditioning to cool the
vehicle interior before you listen to a CD.
 Bumpy roads or other vibrations may make your CD player
skip.
 If moisture gets into your CD player, you may not hear any
sound even though your CD player appears to be working.
Eject all CDs from the player and wait until the player dries.
CAUTION
CD players use an invisible laser beam which could
cause hazardous radiation exposure if directed outside
the unit. Be sure to operate the player correctly.

AUDIO
294
20L038
Correct Wrong
 Handle CDs carefully, especially when you set them into the
player. Hold them on the edge and do not bend them. A void
getting fingerprints on them, particularly on the shiny side.
 Dirt, scratches, warping, pin holes, or other CD damage
could cause the player to skip or to repeat a section of a
track. (To see a pin hole, hold the CD up to the light.)
20L039
To clean a CD: Wipe it with a soft, lint− free cloth that has been
dampened with water. Wipe in a straight line from the center
to the edge of the CD (not in a circle). Do not use a
conventional record cleaner or anti −static device.

STARTING AND DRIVING
299
31L346a
When you enter the vehicle carrying a sm art key and push
the ignition switch, the electronic code in the key is
automatically checked as to whether it corresponds to the
registered ID code for the vehicle. The key indicator light
comes on, the steering column lock is released, and the
engine immobilizer system is cancelled.
At this time, the security indicator light goes off and you can
start the engine when you turn the ignition switch and the key
indicator light does not come on. When you turn the ignition
switch, turn it slowly and surely. If you turn it quickly, it may
become stuck. To free it, see the following “If the ignition switch
seems to be stuck”.
If you push the ignition switch when the smart key is not within
the effective range of the smart key system, a warning tone
sounds and “Key is not Detected” appears on the display. If the ignition switch seems to be stuck:
To free the ignition switch, perform the following:
31L638
1. Push the ignition switch.
31L639
2. Be sure to push the ignition switch while turning the
steering wheel slightly in either direction, and then turn
the switch.