2005 Lexus IS300 brake light

GAUGES, METERS AND SERVICE REMINDER INDICATORS
55
When the ªABSº warning light is on (and the brake system
warning light is off), the anti±lock brake system, the brake
assist system, the traction control system and/or the vehicle
stability control system do not operate, but the brake system
still operates conventionally.
When the ªABSº warning light is on (and the brake system
warning light is off), the anti±lock brake system and/or the
traction
control system do/does not operate so that the wheels
could lock up during a sudden braking or braking on slippery
road surfaces.
If either of the following conditions occurs, this indicates
a malfunction somewhere in the components monitored
by the warning light system. Contact your Lexus dealer as
soon as possible to service the vehicle.
 The light does not come on when the ignition key is turned
to the ªONº position, or remains on.
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If the ªABSº warning light remains on together with the
brake system warning light, immediately stop your
vehicle at a safe place and contact your Lexus dealer.
In this case, not only the anti±lock brake system will fail
but also the vehicle will become extremely unstable
during braking.
(k) Open Door Warning Light
This light remains on until all the doors are completely closed.
(l) Rear Light Failure Warning Light
If this light comes on when the headlight switch is turned on (at
the first or second clickstop), it indicates that one or more of the
tail lights are burned out.
If it comes on when the brake pedal is depressed, one or more
stop lights are burned out.
Have defective bulbs replaced as soon as possible.
(m) Low Fuel Level Warning Light
This light comes on when the fuel level in the tank becomes
nearly empty. Fill the tank as soon as possible.
On inclines or curves, due to the movement of fuel in the tank,
the low fuel level warning light may come on earlier than usual.
(n) ªTRAC OFFº Indicator / Warning Lights
This light comes on when the ignition key is turned to ªONº, and
will go off after a few seconds. This means that the system is
operating properly.
If one of the following conditions occurs, this indicates a
malfunction somewhere in the components monitored by the
warning light system. Contact your Lexus dealer as soon as
possible to service the vehicle.
 The light does not come on after the ignition key is turned
to ªONº.
04 06.30

GAUGES, METERS AND SERVICE REMINDER INDICATORS
57
How to check all the service reminder
indicators
(except the low fuel level warning light):
1. Apply the parking brake.
2. Open the door.
The following service reminder indicator should come on. It
goes off when you close the door completely.
3. Turn the ignition key to ªACCº.
The following service reminder indicator should come on. It
goes off after about 6 seconds.
4. Turn the ignition key to ªONº.
The following service reminder indicators should come on.


or
or

or
The following service reminder indicators go off after a few
seconds.
or

The lights other than the slip indicator light may stay on for
about 60 seconds after the engine is started. It is normal if they
go out after a while.
If any service reminder indicator or warning buzzer does not
function as described above, have it checked by your Lexus
dealer as soon as possible.
04 06.30

OCCUPANT RESTRAINT SYSTEMS
177
Setting the driving position
SV16170
1. Adjust the driver's seat to the desired position.
2. While pushing the ªSETº button, push button ª1º or ª2º
until the signal beeps.
The beep sound means that the positions are recorded in the
computer's memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
SV16171
Automatic transmissionÐ
When you push button ª1º or ª2º, the driving position will
be automatically adjusted to the position recorded for
that button.
Manual transmissionÐ
While button ª1º or ª2º is being pushed down, the driving
position will be automatically adjusted to the position
recorded for that button.
Conditions for memorized position activation
 Automatic transmission: Ignition key ªONº and selector
lever in ªPº position.
 Manual transmission: Ignition key ªONº and apply the
parking brake.
 Ignition switch off and within 30 seconds of opening driver's
door.
04 06.30

STARTING AND DRIVING
236When starting the engine, the key may seem stuck at the
ªLOCKº position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to ªACCº.
CAUTION
For manual transmission:
Never remove the key when the vehicle is moving, as
this will lock the steering wheel and result in loss of
steering control.
PARKING BRAKE
SV31017
To set: Pull up the lever. For better holding power, first
depress the brake pedal and hold it while setting the
parking brake.
To release: Pull up the lever slightly (1) , press the lock
release button (2), and lower (3).
To remind you that the parking brake is set, the parking brake
reminder light in the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, make sure the parking brake is fully
released
and that the parking brake reminder light is off.
04 06.30

STARTING AND DRIVING
237
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3.Manual transmission : Press the clutch pedal to the floor
and shift the transmission into neutral. Hold the clutch pedal to
the floor until the engine is started. A starter safety device will
prevent the starter from operating if the clutch pedal is not fully
depressed.
Automatic transmission: Put the selector lever in ªPº. If you
need to restart the engine while the vehicle is moving, put the
selector lever in ªNº. A starter safety device will prevent the
starter from operating if the selector lever is in any drive
position.
4. For automatic transmission only :Depress the brake
pedal and hold it to the floor until driving off.
Starting the engine
Before starting the engine, be sure to follow the instructions in
ªBefore crankingº.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air±fuel mixture for starting. You can start a cold or hot
engine as follows:
With your foot off the accelerator pedal, crank the engine by
turning the key to ªSTARTº. Release it when the engine starts. Engine should be warmed up by driving, not in idle. For
warming up drive with smoothly turning engine until engine
coolant temperature is within normal range.
If the engine stalls ...
Simply restart it , using the correct procedure given in normal
starting.
If the engine will not start
See ªIf your vehicle will not startº on page 281.
NOTICE
Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.
Do not race a cold engine.
If the engine becomes difficult to start or stallsfrequently, have the engine checked immediately.
04 06.30

STARTING AND DRIVING
240
SS31019

1Power position 2Normal position
3Snow position
2. Set the driving pattern selector switch to the ªNormalº
position.
Your transmission has a driving pattern selector switch which
allows you to select ªPowerº, ªNormalº or ªSnowº mode \
to suit
your driving condition. For ordinary driving, Lexus
recommends that you use the ªNormalº position to improve fuel
economy.
3. For more powerful acceleration and sporty driving, use
the ªPowerº position.
In the ªPowerº position, the ªECT PWRº light in the instrument\
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the
ªNormalº position.
For ªSnowº mode, see ªElectronic Throttle Control
Systemº on page 260.
SV31022

1Brake pedal 2ªDº (Drive) position
4. With your foot holding down the brake pedal, shift the
selector lever to ªDº.
Always use the ªDº position to improve fuel economy and quiet
driving. In this position, shifting into the overdrive gear is
possible. However, while the engine coolant temperature is
low, the transmission will not shift into the overdrive gear even
in the ªDº position. (See ª(c) Using engine brakingº and \
ª(g)
Good driving practiceº for exceptions.)
CAUTION
Never put your foot on the accelerator pedal while
shifting.
04 06.30

STARTING AND DRIVING
246
(g) Good driving practice
If the transmission repeatedly shifts up and down between the
fourth and overdrive gears when climbing a gentle slope, shift
the selector lever to the ªMº position and select the fourth gear
by pushing the transmission switch. Be sure to shift the
selector lever to the ªDº position after climbing the slope.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Always use the brake pedal or the parking brake to hold
the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator pedal, as this can causethe transmission to overheat.
(h) If you cannot shift the selector
If you cannot shift the selector lever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see ªIf you cannot shift automatic transmission
selector leverº on page 304.
(i) If the ªECT PWRº indicator light flashes
If the ªECT PWRº indicator light flashes, contact your Lexus
dealer as soon as possible. There may be trouble in the
transmission system.
04 06.30

STARTING AND DRIVING
251
4Resetting to a slower speed
Press the control lever downward in the ªSET/COASTº
direction and hold it. Release the lever when the desired speed
is attained. While the lever is held downward, the vehicle
speed will gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the ªSET/COASTº direction quickly within
0.6 seconds.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the
ªSET/COASTº direction.
Automatic transmission: Even if you downshift the
transmission from the ªDº position to ªMº with the cruise control
on, engine braking will not be applied because the cruise
control is not cancelled. To decrease the vehicle speed, reset
to a slower speed with the cruise control lever or depress the
brake pedal. If you use the brake pedal, cruise control is
cancelled.
5Resuming the preset speed
If the preset speed is cancelled by pulling the control lever or
by depressing the brake pedal, pushing the lever up in the
ªRES/ACCº direction will restore the speed set prior to
cancellation. However, once the vehicle speed falls below
about 40 km/h (25 mph), the preset speed will not be resumed.
Cruise control failure warning
If the ªCRUISEº indicator light in the instrument cluster flashes
five times and then goes out when using the cruise control, it
means that there is trouble in the cruise control system.
Contact your Lexus dealer.
04 06.30