Page 426 of 668

STARTING AND DRIVING
405
1Brake pedal2ªDº (Drive) position
2. With your foot holding down the brake pedal, shift the
selector lever to ªDº.
Always use the ªDº position to improve fuel economy and quiet
driving. Only in this position, shifting into the overdrive gear is
possible. However, while the engine coolant temperature is
low, the transmission will not shift into the overdrive gear even
in the ªDº position. (See ª(b) Using engine brakingº and\
ª(f)
Good driving practiceº for exceptions.)
CAUTION
Never put your foot on the accelerator pedal while
shifting.
3. Release the parking brake and brake pedal. Depress
the accelerator pedal slowly for smooth starting.
In normal cruising, the vehicle will start in first gear and
automatically shift up to the most suitable gear. On inclines,
declines or winding roads, etc., the vehicle shifts up and down
automatically according to the running conditions to obtain the
suitable driving power and engine braking.
When the lever is in the ª4º position, the automatic
transmission system will select the most suitable gear for the
running conditions such as hill climbing, hard towing, etc.
If you need to accelerate rapidly while driving, depress the
accelerator pedal to the full throttle position. This provides
more acceleration by automatically downshifting the
transmission to the next lower gear or beyond, depending on
the vehicle speed.
If engine braking is needed, such as in descending a long hill,
see ª(b) Using engine brakingº.
Page 427 of 668

STARTING AND DRIVING
406
(b) Using engine braking
To use the braking power of the engine, downshift the
transmission in the way described below:
1Shift into the ª4º position. The transmission will downshift
to fourth gear and engine braking will be enabled.
When the cruise control is being used, even if you
downshift from ªDº to ª4º, engine braking will not be
enabled because the cruise control is not cancelled. If
you need to decrease the vehicle speed, see page 421.
2Shift into the ª3º position. The transmission will downshift
to third gear when the vehicle speed is or becomes lower
than the speed listed below and stronger engine braking
will be enabled.
Transfer ªHº 135 km/h (84 mph) ªLº 52 km/h (32 mph)
3Shift into the ª2º position. The transmission will downshift
to second gear when the vehicle speed is or becomes
lower than the speed listed below and more powerful
engine braking than that of ª3º position will be enabled.
Transfer ªHº 89 km/h (55 mph) ªLº 34 km/h (21 mph)
4Shift into the ªLº position. The transmission will downshift
to first gear when the vehicle speed is or becomes lower
than the speed listed below and maximum engine braking
will be enabled.
Transfer ªHº 39 km/h (24 mph) ªLº 15 km/h (9 mph)
CAUTION
Be careful when downshifting on a slippery surface.
The abrupt change in engine speed could cause the
vehicle to skid or spin.
Page 428 of 668

STARTING AND DRIVING
407
(c) Using the ª3º, ª2º and ªLº positions
The ª3º, ª2º and ªLº positions are used for strong engine\
braking
as described previously.
With the selector lever in ª3º, ª2º or ªLº, you can start the vehicle
in motion as with the lever in ªDº.
With the selector lever in ª3º or ª2º, the vehicle will star\
t in first
gear and automatically shift to second gear.
With the selector lever in ªLº, the transmission is engaged in
first gear.
NOTICE
Be careful not to over±rev the engine. Watch the tachometer to keep engine rpm from going into thered zone. The approximate maximum allowablespeed for each position is given below for yourreference:
Transmission Transfer ªLº ªHº
ª3º 60 km/h (37 mph) 154 km/h (96 mph) ª2º 41 km/h (25 mph) 105 km/h (65 mph)ªLº 24 km/h (15 mph) 61 km/h (38 mph)
Do not continue hill climbing or hard towing for a long time in the ª3º, ª2º or ªLº position. This may causesevere automatic transmission damage from
overheating. To prevent such damage, ª4º positionshould be used in hill climbing or hard towing.
Page 431 of 668
STARTING AND DRIVING
410
When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Always use the brake pedal or parking brake to hold the
vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator pedal, as this can causethe transmission to overheat.
Page 432 of 668

STARTING AND DRIVING
411
(g) If you cannot shift the selector lever
If you cannot shift the selector lever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see ªIf you cannot shift automatic transmission
selector leverº on page 524.
(h) Driving in second start mode
In the second start mode, the transmission system shifts up
from second gear. Use this mode when starting your vehicle
in sand, mud, ice or snow.
To set the second start mode, push the ª2nd STRTº switch. In
the second start mode, the ª2nd STRTº indicator light comes
on. To cancel the second start mode, push the ª2nd STRTº
switch once again.
FOUR±WHEEL DRIVE SYSTEM
(a) Four±wheel drive control
Use the four±wheel drive control lever and center
differential lock switch to select the following transfer and
center differential modes.
The ªHº and ªLº position of the four±wheel drive control leve\
r
provides either lock or unlock mode of the center differential
depending on the center differential lock switch position.
Use the center differential lock system if your wheels get stuck
in a ditch, or when you are driving on a slippery or bumpy
surface. When the center differential is locked, the vehicle
stability control system is automatically turned off and the
center dif ferential lock and ªVSC OFFº indicator lights come on
because the function that controls engine performance
interferes with the process of freeing your wheels.
Page 440 of 668

STARTING AND DRIVING
419
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over about 40 km/h (25 mph) with your foot
off the accelerator pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, a greater
speed change will occur so it is better to drive without the cruise
control.
CAUTION
To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snow±covered) or winding roads.
Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation to
the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.
Turning the system on
To operate the cruise control, push the ªON±OFFº button. This
turns the system on. The indicator light in the instrument
cluster shows that you can now set your desired cruising
speed. Another push on the switch will turn the system
completely off.
When the ignition key is turned off, the ªON±OFFº button is also
automatically turned off. To use the cruise control again, push
the ªON±OFFº button again to turn it on.
CAUTION
To avoid accidental cruise control engagement, keep
the ªON±OFFº button off when not using the cruise
control.
Page 442 of 668

STARTING AND DRIVING
421
4Resetting to a slower speed
Press the control lever downward in the ª± SETº direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the ª± SETº direction quickly.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the ª± SETº
direction.
Even if you downshift the transmission from the ªDº position to
ª4º position with the cruise control on, engine braking will not
be applied because the cruise control is not cancelled. To
decrease the vehicle speed, reset to a slower speed with the
cruise control lever or depress the brake pedal. If you use the
brake pedal, cruise control is cancelled.
5Resuming the preset speed
If the preset speed is cancelled by pulling the control lever or
by depressing the brake pedal, pushing the lever up in the ª+
RESº direction will restore the speed set prior to cancellation.
Cruise control failure warning
If the ªCRUISEº indicator light in the instrument cluster flashes
when using the cruise control, push the ºON±OFFº button to
turn the system off and then push it again to turn it on.
If any of the following conditions then occurs, there is some
trouble in the cruise control system.
The indicator light does not come on.
The indicator light flashes again.
The indicator light goes out after it comes on.
If this is the case, contact your Lexus dealer and have your
Lexus inspected.
Page 443 of 668

STARTING AND DRIVING
422
REAR HEIGHT CONTROL AIRSUSPENSION
This rear height control air suspension controls the
vehicle height depending on the vehicle driving condition.
Select your desired height among the ªHIº (high), ªNº
(normal) and ªLOº (low) modes with the height select
switch.
(a) Vehicle height modes
ªNº (normal) mode: The vehicle height in this mode is
standard. Regardless of the number of occupants or the
luggage loading condition, the vehicle height is always
automatically adjusted to a fixed height in any mode while the
engine is running.
This mode is suitable for ordinary driving. ªHIº
(high) mode: The vehicle height is about 40 mm (1.6 in.)
higher at the rear than the ªNº mode height.
This mode is suitable when driving on the bumpy roads and
through water.
However, when the vehicle speed exceeds about 30 km/h (19
mph) or over in the ªHIº mode, the ªNº mode is automaticall\
y
selected.
CAUTION
The ªHIº mode should be used for severe off±road
driving condition only. As the vehicle's center of gravity
is higher in this setting, the vehicle may become
unstable when turning abruptly resulting in accident.
ªLOº (low) mode: The vehicle height is about 20 mm (0.8 in.)
lower at the rear than the ªNº mode height.
This mode allows you easy access to the vehicle (getting in and
out) and easy loading and unloading operation.
This mode is available when the vehicle speed is under about
12 km/h (7 mph).