2005 KIA Rio oil dipstick

Engine Compartment
7-13
Engine coolant reservoir Radiator cap Engine oil fill capAir cleanerAuto transaxle fluid
dipstick (if equipped)Brake/clutch
fluid reservoir
Engine oil dipstick Windshield
washer
fluid
reservoir Power steering
fluid reservoir
(if equipped)Fuse box
Battery
2FDA604
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 13

Engine Oil and Oil FilterChecking the Engine Oil Level1. Be sure the vehicle is on level ground.
2. Start the engine and allow it to reach normal
operating temperature.
3. Turn the engine off and wait a few minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and re-insert it
fully.
5. Pull the dipstick out again and check the level. The
level should be between F and L.
If it is near or at L, add enough oil to bring the level to
F. Do not overfill.Maintenance7-14
Use only the specified engine oil. (Refer to
“Recommended Lubricants’’ later in this section.)
2FDA605
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 14

Changing the Engine Oil and FilterChange engine oil and filter according to the
Scheduled Maintenance earlier in this section.
1. Warm the engine up for a few minutes and then
turn it off. Remove the oil filler cap.
2. Drain the oil into a suitable container after
removing the oil filler cap and drain plug.
3. Remove the engine oil filter with an oil filter
wrench.4. Use a clean rag to clean the oil filter mounting
surface on the engine.
5. Apply a small amount of engine oil to the new oil
filter O-ring seal.
6. Install the oil filter and tighten it. (Refer to
the oil filter caution label for tightening
instructions.)
7. Replace the drain plug tightly after the oil has
thoroughly drained.
8. Refill the engine with new oil to the F mark on the
dipstick. Do not overfill.
7-15
WARNING - Engine Oil
 Continuous contact with USED engine oil
has caused skin cancer in laboratory mice.
Protect your skin by washing with soap and
water.
 Keep all engine oil out of the reach of
children.
CAUTION
Both the oil and engine are hot. Do not burn
yourself.
✻ ✻
NOTICE
When installing the replacement oil filter, do not
allow the oil filter gasket to remain on the oil
filter mounting surface. This will cause oil
leakage and engine damage. Remove the old
gasket completely so that a new gasket will
properly seat and seal.
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 15

Maintenance7-48
Engine oil viscosity (thickness) has an effect on fuel
economy and cold weather operation (starting and oil
flow). Lower viscosity engine oils can provide better
fuel economy and cold weather performance, however,
higher viscosity engine oils are required for
satisfactory lubrication in hot weather. Using oils of
any viscosity other than those recommended could
result in engine damage.
When choosing an oil, consider the range of
temperature your vehicle will be operated in before the
next oil change. Then select the recommended oil
viscosity from the chart.
✻ ✻
NOTICE
Always be sure to clean the area around any filler
plug, drain plug, or dipstick before checking or
draining any lubricant. This is especially
important in dusty or sandy areas and when the
vehicle is used on unpaved roads. Cleaning the
plug and dipstick areas will prevent dirt and grit
from entering the engine and other mechanisms
that could be damaged.
Recommended SAE Viscosity Number
Temperature Range for SAE Viscosity Numbers
Temperature
Gasoline
Engine Oil°C
(°F)
-30 -20 -10 0 10 20 30 40 50
-10 0 20 40 60 80 100 120
10W-30
5W-20, 5W-30
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 48