2005 JEEP GRAND CHEROKEE ignition

mirror, and the pedals stop moving. A delay of one
second will occur before another recall can be selected.
To Disable A Transmitter Linked to Memory
1. Turn the ignition switch to the OFF position and
remove the key.
2. Press and release memory button number 1. The
system will recall any memory settings stored in position
1. Wait for the system to complete the memory recall
before continuing to step 3.
3. Press and release the memory SET (S) button located
on the driver’s door.4. Within 5 seconds, press and release memory button 1
on the driver’s door.
5. Within 5 seconds, press and release the “Unlock”
button on the Remote Keyless Entry transmitter.
To disable another transmitter linked to either memory
position, repeat steps 1-5 for each transmitter.
NOTE:Once programmed, all transmitters linked to
memory can be easily enabled or disabled at one time.
Refer to Remote Linked to Memory underCustomer
Programmable Featuresin the Electronic Vehicle Infor-
mation Center (EVIC) for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
3

Multi-Function Control Lever
The multi-function control lever controls the operation of
the headlights, turn signals, headlight beam selection,
instrument panel light dimming, passing light, interior
courtesy/dome lights, and optional fog lights.
Battery Saver Feature—Exterior/Interior Lights
If the multi-function control lever is left in the interior
light position, parking light position, or the headlight
position when the ignition switch is moved to the OFF
position, the battery saver feature will automatically turn
off the exterior and interior lights after eight minutes.
Normal operation will resume when the ignition is
turned ON or when the headlight switch is turned to
another position.
Multi-Function Control Lever
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:Broken, muddy, or obstructed headlights and
taillights of vehicles in the field of view will cause
headlights to remain on longer (closer to the vehicle).
Also, dirt, film, and other obstructions on the windshield
or camera lens will cause the system to function improp-
erly.
Instrument Panel and Interior Lights
When the multi-function control lever is in the parklight,
headlight, or A (Auto) position (if equipped), rotating the
center portion of the lever up and down will increase and
decrease the brightness (dimmer control) of the instru-
ment panel lights. Full daytime brightness on all elec-
tronic displays (odometer, overhead console, radio, and
Automatic Climate Control (if equipped) is obtained by
rotating the center portion of the control to the first
detent above the dimmer range. Rotating the control to
the second detent above the dimmer range turns the
interior lights on. Rotating the control to the “Off”
(extreme bottom) position disables all the interior lights,even when the doors and liftgate are open. While in the
“Off” position the instrument panel lighting is at the
lowest light level and may not be suitable for night
driving.
Daytime Running Lights — Canada Only
The headlights come on at a low intensity level whenever
the engine is running. The lights remain on until the
ignition switch is turned OFF or the parking brake is
engaged. The headlight switch must be used for normal
night time driving.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound when the driver’s door
is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
3

Headlight Time Delay
There is also a feature that delays turning off the vehicle
lights for 30, 60, or 90 seconds after the ignition switch is
turned OFF. To activate the headlight delay, the multi-
function control lever must be rotated to the “Off”
position after the ignition switch is turned OFF. Only the
headlights will illuminate during this time. Refer to
“EVIC- Customer Programmable Features” in Section 4
to turn this feature “On/Off” or set the time interval.
WINDSHIELD WIPERS AND WASHERS
The front and rear wipers and washers are operated by a
switch in the right side control lever. Turn the end of the
control lever to select “Lo,” “Hi,” or one of the five speed
sensitive intermittent windshield wiper speeds. Refer to
“Speed Sensitive Intermittent Wiper System” in this
section. For information on the rear wiper and washer
refer to “Rear Window Features” in this section.NOTE:Always remove any build-up of snow that
prevents the windshield wiper blades from returning to
the OFF position. If the windshield wiper switch is
turned off and the blades cannot return to the OFF
position, damage to the wiper motor may occur.
Windshield Wiper/Washer Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
3

“TRACTION SYS DISABLED” message will be displayed
in the Electronic Vehicle Information Center (EVIC).
Refer to Section 4 of this manual.
To turn the system back ON, press the switch a second
time, until the “Traction Control Indicator Light” turns
off.When the Traction Control System has been turned off
using the switch, a feature of the system remains active.
This feature functions similar to a limited slip differential
and controls the wheel spin across an axle. If one wheel
on an axle is spinning faster than the other, the system
will apply the brake of the spinning wheel and allow
more engine torque to be applied to the wheel that is not
spinning.
NOTE:
•The “Traction Control Indicator Light” comes on mo-
mentarily each time the ignition switch is turned ON.
This will occur even if you used the switch to turn the
system OFF.
•Each time the ignition is turned ON, the Traction
Control System will be ON even if it was turned OFF
previously.
•The Traction Control System will make buzzing or
clicking sounds when it is active.
Traction Control Switch
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

There are two Electronic Vehicle Information Center
(EVIC) messages associated with the Traction Control
System. Refer to Section 4 of this manual.
Traction Sys Disabled
This message will be displayed if the Traction Control
System has been turned off using the switch, or if there is
a temporary condition that will will result in partial or no
Traction Control System function. The “Traction Control
Indicator Light” will be on when the system is disabled
or only partial function is allowed. The “TRACTION SYS
DISABLED” message and the “Traction Control Indicator
Light” being illuminated without the switch being de-
pressed is not an indication that service of the electronic
brake system is required.Service Elec Brake System
This message will be displayed if a condition exists that
may require servicing the electronic brake system. When
this message is displayed and the “Traction Control
Indicator Light” is on, there is a malfunction of the
Traction Control System. If the “SERVICE ELEC BRAKE
SYSTEM” message continues to be displayed after sev-
eral ignition cycles and the vehicle has been driven
several miles at speeds greater than 30 mph (48 km/h),
see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
3

than the other, the system will apply the brake of the
spinning wheel and allow more engine torque to be
applied to the wheel that is not spinning.
To improve the vehicle’s traction when driving with
snow chains, or starting off in deep snow, sand or gravel,
it may be desirable to switch off the ESP by pressing the
ESP switch.
With the ESP switched off, the engine torque reduction
and stability features are cancelled. Therefore, the en-
hanced vehicle stability offered by ESP is unavailable.
If the “ESP Indicator Light” begins to flash during
acceleration, ease up on the accelerator and apply as little
throttle as possible. Be sure to adapt your speed and
driving to the prevailing road conditions. When the “ESP
Indicator Light” is illuminated continuously, the ESP is
switched off. To return to the enhanced vehicle stability
offered by ESP, press the ESP switch (the “ESP IndicatorLight” in the instrument cluster goes out). Avoid spin-
ning one drive wheel. This may cause serious damage to
the drive train.
NOTE:
•The “ESP Indicator Light” comes on momentarily each
time the ignition switch is turned ON.
•Each time the ignition is turned ON, the ESP System
will be ON even if it was turned off previously.
•The ESP Control System will make buzzing or clicking
sounds when it is active.
There are two Electronic Vehicle Information Center
(EVIC) messages associated with the Electronic Stability
Control System. Refer to Section 4 of this manual.
ESP System Disabled
This message will be displayed if the ESP System has
been turned off using the switch, or if there is a tempo-
rary condition that will result in partial or no ESP
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

function. The “ESP Indicator Light” will be on when the
system is disabled or only partial function is allowed. The
“ESP SYSTEM DISABLED” message and the “ESP Indi-
cator Light” being illuminated without the switch being
depressed is not an indication that service of the elec-
tronic brake system is required.
Also, the “ESP SYSTEM DISABLED” message will be
present when the vehicle is shifted into 4WD LOW.
Service Elec Brake System
This message will be displayed if a condition exists that
may require servicing the electronic brake system. When
this message is displayed and the “ESP Indicator Light”
is on, there is a malfunction of the ESP System. If the
“SERVICE ELEC BRAKE SYSTEM” message continues to
be displayed after several ignition cycles and the vehicle
has been driven several miles at speeds greater than 30
mph (48 km/h), see your authorized dealer for service.CAUTION!
The manufacturer recommends towing with all four
wheels off the ground. Acceptable methods are to
tow the vehicle on a flatbed or with one end of the
vehicle raised and the other end on a towing dolly.
REAR PARK ASSIST SYSTEM— IF EQUIPPED
The Rear Park Assist System provides visual and audible
indications of the distance between the rear fascia and the
detected obstacle when backing up. Refer to the Warning
Section and Note Section for limitations of this system
and recommendations.
The Rear Park Assist System will remember the last
system state (enabled or disabled) from the last ignition
cycle when the ignition is changed to the RUN/ON
position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127
3